Life Span Workplace DT-5 User manual

DT5, DT7
Treadmill/Bike Desk
Owner’s Manual

3
Table of Contents
Welcome
Getting Started
Welcome
Warranty
DT5 Desk Assembly
Assembly Instructions
Desk Leveling and Height Adjustment
DT7 Desk Assembly
Assembly Instructions
Desk Leveling and Height Adjustment
DT5 Manual Treadmill Desk Assembly
DT7 Electric Treadmill Desk Assembly
Treadmill Desk Operations
Specications
Setting the Clock
Starting the Treadmill Desk
Console Overview
Preset Key & Bluetooth
Innovative Features
Troubleshooting
Personal Settings
Display Details
Bike Desk Operations
Specications
Setting the Clock
Starting the Bike Desk
Console Overview
Preset Key & Bluetooth
Troubleshooting
Personal Settings
Display Details
5
8
16
25
26
27
39

54
Welcome
Congratulations on choosing the LifeSpan Workplace™ line of products. These
products give you the opportunity to remain productive while taking care of
yourself as you integrate movement with normally sedentary tasks.
The average American now spends eleven hours, ve days a week, sitting, and
burns one-hundred fewer calories each day than they did a few decades ago.
Sitting for long periods slows your metabolism, reduces calories burned, and
increases your risk for heart disease and diabetes.
Whether you plan on placing this product in a TV room, replace your desk at
home or are adding another workspace in the oce, LifeSpan Workplace™
products are a great way to add movement to an otherwise sedentary activity.
Before you assemble or operate your product, please read this manual
thoroughly. Important information, including safety precautions, ongoing
product maintenance, assembly instructions, and information on proper
operation are included.
If you need to contact LifeSpan customer service, visit our website at
www.LifeSpanFitness.com and select customer service. Complete the
information requested and we will respond to your inquiry within one
business day. In the United States and Canada you can also call
[phone] and choose option 4.
Neither LifeSpan Fitness nor its representatives can accept responsibility for any damages or
injury incurred as a result of information presented in this manual except under the terms
of the product warranty.

76
Warranty
Your LifeSpan treadmill/bike desk comes with the following limited warranty
valid in North America and the United Kingdom. If you are outside of these
areas contact your local distributor for warranty information or visit
www.LifeSpanFitness.com.
LifeSpan warrants the equipment it manufactures is free from defects in
materials and workmanship under normal use and services. The periods above
are based on the date of purchase. During these periods, LifeSpan will repair
or replace any defective part. Free labor is included on all parts that are not
normally assembled or replaced by the customer within the labor period.
If within the time frames specied above, any part fails to operate properly,
login to our website at www.LifeSpanFitness.com, click on “Customer Service”
and complete the form to request assistance or call 877.654.3837 option 4 for a
Customer Service Agent (please note that certain kinds of service should only
be performed by a qualied service technician).
LifeSpan reserves the right to make changes and improvements to our products
without incurring any obligations to similarly alter any product purchased.
In order to insure our product warranty and to ensure the safe and ecient
operation of your LifeSpan product, only authorized parts can be used. The
warranty is void if any parts other than those provided by LifeSpan are used.
Exclusions and Limitations:
• This warranty does not apply to any defects caused by negligence, misuse,
improper assembly, or maintenance, accident, or “act of God.”
• This warranty does not apply to discoloration of paints or plastics.
• LifeSpan shall not be responsible for incidental or consequential damages.
• This warranty is non-transferable form the original owner.
Registration
Should you need to process a warranty claim make sure you retain your
purchase receipt to verify the date of purchase and register your LifeSpan
product online. To complete the registration go to www.LifeSpanFitness.com
and select “Product Registration”.
Warranty
Frame
Parts
Labor
DT5
Lifetime
2 Years
1 Year
DT7
Lifetime
2 Years
1 Year

98
DT5 Desk: Assembly Instructions
At LifeSpan we strive to make our equipment easy to assemble and start
using. Parts that can be pre-assembled are always assembled and tested on
the product line.
Prior to starting the assembly process, take all the parts out of the box,
remove plastic bags and lay everything out on the oor to become familiar
with the components.
Since your desk is a heavy piece of equipment, it is recommended that you
use two people during assembly and follow these assembly instructions to
reduce any problems that may occur.
DT5 Desk: Assembly Instructions
4
3
6
A
1
8
7
9
B
C
10
5
11
2
14
16
16
13
15
15
15
17
16a
Hardware Included
Item# Part Description Item# Part Description
1 Lift Frame 8 LifeSpan Placard **
2 Desktop 9 M8x45L Bolt **
3 Left Base Foot 10 M8 Nuts **
4 Right Base Foot 11 Wire Cover
5M8 Washer ** 12 M10 Washer **
6 M10 Acorn Nut ** 13 U-Shape Frame
7 Height Ad. Knob 14 Console
**Pre-installed
A Desk Position Bumpers
BExtension Tube
C Desktop Mounting Bracket
Hardware Bag Contents
Item # Qty. Part Description
15 6 M6x40L Screw
16 8 #8x5/8L Screw
16a 2 #8x1/2L Screw
17 1 Wire Harness Cover
18 1 Wrench - 17mm
19 1 4mm Allen Wrench 20 1
5mm Allen
Wrench w/Phillips
Screwdriver
Table corresponds to the diagram on the left
Boxed Separately
5mm Allen
Wrench w/
Phillips
Wrench Wire Harness
Cover
M6x40L
Screw
4mm Allen
Wrench
#8x5/8L
Screw
#8x1/2L
Screw

1110
DT5 Desk: Assembly Instructions
Step 1: Lift Frame Assembly
A. Position the Lift Frame (1),
Left Base Foot (3) and Right
Base Foot (4) as shown in
the gure to the right.
NOTE: The position of the
Desk Position Bumpers (A)
face inward, and the
long side of the Right and
Left Base Feet (3, 4) are
opposite of the Height
Adjustment Knobs (7)
B. Place the Lift Frame onto
the left and right Base Feet
mounting bolts and install
the M10 washers (5) and
M10 acorn nuts (6).
C. Tighten the four mounting
nuts.
Step 2: Install the Height
Adjustment Knobs
A. Locate the Height
Adjustment Knobs (7).
B. Screw the Height
Adjustment Knobs into the
Lift Frame (1) uprights as
shown in the gure to the
right.
C. Raise each Extension Tube
(B) to level 15 and tighten
the Height Adjustment
Knobs (7).
Step 3: Attach U-Frame to Underside of Desk
A. Lay the Desktop (2) face down on a smooth clean surface to attach the
U-Frame (13).
B. Position the U-Frame (13) as shown to the underside of the Desktop (2).
Be sure the open part of the frame faces toward the Cable Hole. The
stickers labeled "RRR" on the Desktop and U-Frame should be matched
together when assembled.
C. Attach the U-Frame to the Desktop using the six M6x40L Screws (15) using
the 4mm Allen Wrench (19).
4
3
6
A
1
8
7
7
9
B
C
10
5
11
2
14
16
16
13
15
15
15
17
16a
DT5 Desk: Assembly Instructions
Desk
Position
Bumpers
face
inward
Long Side
Short
Side
7
1
B
Wrench
2
13
Cable Hole
"RRR"
Stickers
M6x40L
Screw
4mm Allen
Wrench
"RRR"
Stickers

1312
216
16
14
14
Step 4C
Step 4D
Step 4C Step 5A:
Remove End
Caps
Step 5B & C:
Attach Console
9
10 5
B
C
DT5 Desk: Assembly Instructions DT5 Desk: Assembly Instructions
Step 4: Desktop Assembly
A. Make sure the Extension Tube (B) is at level 15 (done in step 2C).
B. Align the Desktop on top of the Extension Tubes (B) so the wire harness
from the Desktop U-Frame is on the same side as the wire harness
coming from the right extension tube. Gently lower the desktop support
frame onto the Desktop Mounting Bracket (C).
Step 5: Console Assembly
A. Using the 5mm Allen Wrench with Screwdriver (20) take out the two pre-
installed screws from the back and two screws from the bottom of each
console end cap so you can remove the end caps. Notice the dierence in
the screws from the back and bottom as you will be replacing them back
into their proper place.
B. Align the screw holes in the Console Bracket (14) with the pre-drilled holes
in the Desktop (2).
C. Using eight #8x5/8L Screws (16) attach the Console (14) to the Desktop (2).
D. Re-install the end caps with the pre-installed screws you removed in
Step A.
C. Insert four M8x45L carriage bolts (9) through the Mounting Brackets.
Install four M8 washers (5) and nuts (10). Securely tighten the four M8 nuts.
D. Connect the two wire harness connectors.
NOTE: Make sure the console wire harness or connector does
not get caught or pinched between the mounting bracket
and desktop frame.
NOTE: If the desktop tilts up and down slightly, re-tighten the four
bolts/nuts inserted in step 4C.
Wrench
#8x5/8L
Screw
5mm Allen
Wrench w/
Phillips
5mm Allen
Wrench w/
Phillips
Step 5D:
Re-Install
End Caps

1514
Desk Leveling
The desk needs to be leveled
prior to use. The desk comes
with two Adjustable Feet that
can be used to level the desk
and eliminate rocking. If the
desk is rocking on two of the
feet, adjust the two front feet
until all four feet are sitting
securely on the oor.
Desk Adjustment Feet
Desk Height Adjustment
A. Loosen the Adjustment Knobs (A)
on each upright by turning it no
more than two turns counter-
clockwise.
B. While rmly holding each
side of the Desktop, pull both
Adjustment Knobs out and slowly
raise or lower the desktop.
C. Release the Adjustment Knob as
the desired level is reached. The
Adjustment Knob will click into
place.
D. Check to make sure the desk
height is set at the same level on
both sides. Turn the Adjustment
Knobs clockwise to lock in place.
DT5 Desk: Desk Leveling and Height AdjustmentDT5 Desk: Assembly Instructions
Step 7: Attach the Wire Cover to the Right Extension Tube
A. Simply snap the Cover (11) over the Right Extension Tube (B). The
bottom of the cover will be resting on top of the Stop Bumper (D).
Step 6: Connecting the Wires
A. Underneath the front of the Desktop(2) connect the two 7-pin wire
harnesses together for console operation.
B. Attach the Console Wire Harness Cover (17) to the underside of the
Desktop(2) using two #8x1/2L Screws (16a). Push all the extra cable back
into U-Frame to help t cover in place.
B
11
D
17
2
16a
From Console
From U-Frame
under Desktop
Step 6A
Step 6B:
Attach Wire
Harness
Cover
Wire Harness
Cover
5mm Allen
Wrench w/
Phillips
Step 6B:
Attach Wire
Harness
Cover
#8x1/2L
Screw

1716
DT7 Desk: Assembly Instructions
At LifeSpan we strive to make our equipment easy to assemble and start
using. Parts that can be pre-assembled are always assembled and tested on
the product line.
Prior to starting the assembly process, take all the parts out of the box,
remove plastic bags and lay everything out on the oor to become familiar
with the components.
Since your desk is a heavy piece of equipment, it is recommended that you
use two people during assembly and follow these assembly instructions to
reduce any problems that may occur.
Table corresponds to the diagram on the left
DT7 Desk: Assembly Instructions
B
1
6
11
3
4
10
C
9
A
7
5
8
5
2
14
13
15
15
15
16
16
17
16a
Boxed Separately
Hardware Included
Item# Part Description Item# Part Description
1 Lift Frame 8 M8 Lock Nut **
2 Desktop 9 M8x15L Bolt **
3 Left Base Foot 10 Accessory Tray
4 Right Base Foot 11 M10 Washer **
5M8 Washer ** 12 LifeSpan Placard
6 M10 Acorn Nut ** 13 U-Shape Frame
7 M8x45L Bolt ** 14 Console
**Pre-installed
A Desk Position Bumpers
BExtension Tube
C Desktop Mounting Bracket
Hardware Bag Contents
Item # Qty. Part Description
15 6 M6x40L Screw
16 8 #8x5/8L Screw
16a 2 #8x1/2L Screw
17 1 Wire Harness Cover
18 1 Wrench - 17mm
19 1 4mm Allen Wrench 20 1
5mm Allen
Wrench w/Phillips
Screwdriver
5mm Allen
Wrench w/
Phillips
Wrench Wire Harness
Cover
M6x40L
Screw
4mm Allen
Wrench
#8x5/8L
Screw
#8x1/2L
Screw

1918
DT7 Desk: Assembly Instructions
Step 1: Lift Frame Assembly
A. Position the Lift Frame (1),
Left Base Foot (3) and Right
Base Foot (4) as shown in
the gure to the right.
NOTE: The position of the
Desk Position Bumpers (A)
face inward, and the
long side of the Right
and Left Base Feet (3, 4)
are opposite of the
Access Panel
B. Place the lift frame
onto the left and right
base feet mounting
bolts and install the M10
washers (11) and M10
acorn nuts (6).
C. Tighten the four mounting
nuts.
Step 2: Accessory Tray Assembly
A. Remove the four
Screws (9) pre-
installed in the
bottom of the
Upright Assembly
Crossbar.
B. Line the holes in
the accessory tray
(10) with the holes
in the Crossbar.
C. Install four M8
washers and
M8x15 bolts (9) and
tighten.
9
10
DT7 Desk: Assembly Instructions
Step 3: Attach U-Frame to Underside of Desk
A. Lay the Desktop (2) face down on a smooth clean surface to attach the
U-Frame (13).
B. Position the U-Frame (13) as shown to the underside of the Desktop (2).
Be sure the open part of the frame faces toward the Cable Hole. The
stickers labeled "RRR" on the Desktop and U-Frame should be matched
together when assembled.
C. Attach the U-Frame to the Desktop using the six M6x40L Screws (15) using
the 4mm Allen Wrench (19).
2
13
Cable Hole
"RRR"
Stickers
M6x40L
Screw
4mm Allen
Wrench
1
6
11
3
4
A
2
14
13
15
16
16
17
16a
Desk
Position
Bumpers
face
inward
Long Side
Short
Side
Access
Panel
Wrench