Life Span entertainer User manual

- -
ENTERTAINER
0
Product may vary slightly from the item pictured due to model upgrades
OWNER'S MANUAL
ENTERTAINER

- -
ENTERTAINER
1
1. IMPORTANT SAFETY INSTRUCTIONS
Danger–To reduce the risk of electric shock disconnect your treadmill from the electrical outlet prior to
cleaning and/or service work.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY
USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET.
Install the treadmill on a flat level surface with access to a 220-240 volt (50/60Hz), grounded outlet.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and
treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 1 metre clearance between the rear of
the treadmill and any fixed object.
Place your unit on a solid, level surface when in use.
Never allow children on or near the treadmill.
When running, make sure the plastic clip is fastened on your clothing. It is for your safety, should you
fall or move too far back on the treadmill.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug.
Keep the cord away from heated surfaces.
WARNING - Read all instructions before using this treadmill.
It is important your treadmill receives regular maintenance to prolong its useful life. Failing
to re
g
ularl
y
maintain
y
our treadmill ma
y
void
y
our warrant
y
.

- -
ENTERTAINER
2
Do not operate where aerosol spray products are being used or where oxygen is being administered.
Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
The treadmill is intended for in-home use only and not suitable for long time running.
To disconnect, turn all controls to the off position, remove the safety key, and then remove the plug
from the outlet.
The pulse sensors are not medical devices. Various factors, including the user’s movement, may
affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in
determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your
treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Allowed temperature: 5 to 40 degrees.
Remove the safety key after use to prevent unauthorized treadmill operation.
1.1 IMPORTANT ELECTRICAL INFORMATION
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power cord
away from any moving part of the treadmill including the elevation mechanism and transport wheels.
NEVER remove any cover without first disconnecting AC power.
NEVER expose this treadmill to rain or moisture. This treadmill is not designed for use outdoors, near
a pool, or in any other high humidity environment.
1.2 IMPORTANT OPERATION INSTRUCTIONS
Be sure to read the entire manual before operating your machine.

- -
ENTERTAINER
3
Understand that changes in speed and incline do not occur immediately. Set your desired speed on
the computer console and release the adjustment key. The computer will obey the command
gradually.
Use caution while participating in other activities while walking on your treadmill; such as watching
television, reading, etc. These distractions may cause you to lose balance or stray from walking in
the centre of the belt; which may result in serious injury.
In order to prevent losing balance and suffering unexpected injury, NEVER mount or dismount the
treadmill while the belt is moving. This unit starts with at a very low speed. Simply standing on the
belt during slow acceleration is proper after you have learned to operate this machine.
Always hold on to handrail while making control changes.
A safety key is provided with this machine. Remove the safety key will stop the walking belt
immediately; the treadmill will shut off automatically. Insert the safety key will reset the display.
Do not use excessive pressure on console control keys. They are precision set to function properly
with little finger pressure.

- -
ENTERTAINER
4
ASSEMBLY INSTRUCTIONS
When you open the carton, you will find the below spare parts:
SPARE PARTS:
# DESCRIPTION REMARKS Q’TY
1 UPRIGHT CONNECTED
SYPHON 1
2 MAIN FRAME 1
3 LEFT UPRIGHT 1
4 RIGHT UPRIGHT 1
5 COMPUTER 1
118 PLASTIC COVER 2
14 BOLT M10*20 12
32 SCREW M6*10 4
38 FLAT WASHER 10 12
ALLEN WRENCH 5mm 1
ALLEN WRENCH 6mm 1
WRENCH W/SCREW
DRIVER 1

- -
ENTERTAINER
5
TOOLS REQUIRED:
ALLEN WRENCH 5MM 1pcs ALLEN WRENCH 6MM 1pcs
WRENCH W/SCREW DRIVER 13、14、15 1pcs
STEP (1):
组装步骤三：
STEP (2):
1.Connect the computer cables of
right upright (4) and main frame (2)
firstly; Insert right upright (4) into
main frame (1), and then connect
them with bolts (14) and flat
washers (38).
CAUTION:
A. Please don’t damage the wires
while doing assembly.
B. Please don’t tighten ALL BOLTS
before STEP (4)
2. Insert left upright (3) into main frame
(2), and then connect them with bolts
(14) and flat washers (38).
CAUTION:
A. Please don’t damage the wires
while doing assembly.
B. Please don’t tighten ALL BOLTS
before STEP (3)

- -
ENTERTAINER
6
6. Connect the right cable of the computer (5)
and the cable of the right upright (4) firstly.
Insert computer left handlebar board into left
upright (3) and right upright (4). Connect them
with the bolts M8*20 (38) and flat washer (14).
7. To lock the computer right fixed board into
the right upright (4).
CAUTION: Tighten all the bolts again.
3. Cross the upright connected tube (1)
into plastic cover (118) and insert it into
the left upright (3).
4. Repeat the step 3, cross the upright
connected tube (1) into plastic cover (118)
and insert it into the right
5. Lock the upright connected tube into
the left and right upright with screw M6*10
(32).
STEP (3):
STEP (4):

- -
ENTERTAINER
7
CAUTION:
1. DO NOT PLUG IN POWER CORD UNTIL FINAL ASSEMBLY IS COMPLETED AND MOTOR COVER
IS INSTALLED.
2. Do not attempt to assemble the treadmill unless the assembly instructions are followed and the uprights
are attached to the treadmill. Failure to follow this can result in damage to the treadmill.
3. Your treadmill is a very heavy piece of exercise equipment so should be handled with caution.
4. Children should not be allowed to play on the treadmill or move the treadmill deck up and down.
TECHNICAL PARAMETER
BUILT UP SIZE(mm) 1870*880*1510 POWER 220~240V（50~60HZ）
RUNNING BELT SIZE(mm) 3000 x520 SPEED RANGE 1—20Km/h
FOLDABLE SIZE(mm) 1220*880*1615 NET WEIGHT 144KGS
LED DISPLAY SPEED, DISTANCE, CALORIES, PULSE, TIME and INCLINE

- -
ENTERTAINER
8
EXERCISE GUIDE
PLEASE NOTE: Before beginning any exercise program, consult you physician. This is important
especially if you are over the age of 45 or individuals with pre-existing health problems.
The pulse sensors are not medical devices. Various factors, including the user’s movement, may
affect the accuracy of heart rate readings. The pulse sensors are intended only as an exercise aid
in determining heart rate trends in general.
Exercising is great way to control your weight, improving your fitness and reduce the effect of aging and
stress. The key to success is to make exercise a regular and enjoyable part of your everyday life.
The condition of your heart and lungs and how efficient they are in delivering oxygen via your blood to your
muscles is an important factor to your fitness. Your muscles use this oxygen to provide enough energy for
daily activity. This is called aerobic activity. When you are fit, your heart will not have to work so hard. It will
pump a lot fewer times per minute, reducing the wear and tear of your heart.
So as you can see, the fitter you are, the healthier and greater you will feel.
Warm-up
Start each workout with 5 to 10 minutes of stretching and some light exercises. A proper warm-up
increases your body temperature, heart rate and circulation in preparation for exercise. Ease into your
exercise.

- -
ENTERTAINER
9
Training zone Exercise
After warming up, increase the intensity to your desired exercise program. Be sure to maintain your
intensity for maximum performance. Breathe regularly and deeply as you exercise-never hold your
breathe.
Cool Down
Finish each workout with a light jog or walk for at least 1 minute. Then complete 5 to 10 minutes of
stretching to cool down. This will increase the flexibility of your muscles and will help prevent post-exercise
problems.
Workout Guidelines
TARGET ZONE
THIS IS HOW YOUR PULSE SHOULD BEHAVE DURING GENERAL FITNESS
EXERCISE. REMEMBER TO WARM UP AND COOL DOWN FOR A FEW MINUTES.
The most important factor here is the amount of effort you put in. The harder and longer you work the
more calories you will burn. Effectively this is the
same as if you were training to improve your fitness, the difference is the goal.

- -
ENTERTAINER
10
OPERATION GUIDE
Window display:
1、"CAL/ PULSE" windows: Display the total workout calories or the total workout pulse,
normally display calories from 0-999 and to 999 spill over to clear 0. When your workout
count/counts down from the inverse direction, it will counts down to 0. When the data will be

- -
ENTERTAINER
11
decreased gradually to 0 and the data what set up will go on starting from the positive
direction to increase the data , and will make Bi-Bi... 10 sounds. The speed will be decreased
to the lowest speed and the incline will be decreased to 0. The system can sense the user's
heartbeat frequency automatically when the user holds the hand pulse and will show the
data on the windows. At the same time, the corresponding indicator light will lighten. The
heartbeat value display range: 60-200 times/min.
2、“TIME”windows: Display the exercise time positive direction clock from 0：00-99：59，
To 99：59 spill over from 0：00 to reset. When the data will be decreased gradually to 0:00
and the data what set up will go on starting from the positive direction to increase the data
and will make Bi-Bi... 10 sounds. The speed will be decreased to the lowest speed and the
incline will be decreased to 0.
3、"DISTANCE" windows: Display the exercise distance, the positive direction from
0.00KM-99.9KM，to 99.9KM spill over to clear 0, From the inverse direction, the data will be
decreased gradually to 0 from the setting value. And the data what set up will go on starting
from the positive direction to increase the data, and will make Bi-Bi... 10 sounds. The speed
will be decreased to the lowest speed and the incline will be decreased to 0.
4、“SPEED”windows: Display the exercise speed 1.0-20KM/H.
5、“INCLINE”windows:Display the incline，0-20 levels.
6、7 INCH VIDEO DISPLAY SD CARD OR THE CONTENT OF OUTSIDE VIDEO.
BUTTON FUNCTIONS:
A.“POWER”button：power switch，turn on and close down the computer power, it also can
cut down the motor power. Press the button,“TIME”window will show the weight value
（70kg），press“INCLINE”“SPEED”to set up the weight, then press“ENTER”button
to confirm.
B.“SELECT”button：To choose the program and press the button will cycle display 0：00;
15:00; 1.0; 50; P1-P24 on the TIME windows (0:00 is manual mode, 15:00 is time count
down, 1.0 is distance count down, 50 is calories count down, P1-P24 is inner install
program).
C.“ENTER”button:Confirm and enter into next step to go on confirmation for the setting
parameter function.
D. “VOL+” “VOL-“: volume plus/minus button: When you display SD card or outside
connected the video, press the button, you can adjust the volume.
E. “MUTE”: is whisht button: Press the button without any voice when you play the SD card
or outside frequency.

- -
ENTERTAINER
12
F.“START”button：When start the power and attach the magnet end of the safety pulling
rope to the computer. Press the button at any time, it can start the running. When it starts
again that is for manual mode, the treadmill will start from the lowest speed 1.0KM/H and the
incline will be 0.
G.“STOP”button：Press the button at any time, it can stop the running.
H.“SPEED+/-”button：To adjust the setting value when the treadmill is not running, when
it starts to run the machine, it can adjust the speed, the speed will be changed 0.1km/hour
each time you press the button. If you press the button over 0.5S continuous, then it will
change the speed quickly.
I.“INCLINE+/-”button：To adjust the setting value when the treadmill is not running, when
it starts to run the machine, it can adjust the incline, the incline will be changed 1 level each
time you press the button. If you press the button over 0.5S continuous, then it will change
the incline quickly.
J.“2-20 levels”button：Incline shortcut key, it is valid when the treadmill is running, then
press the button to adjust the incline quickly.
K. 2KM-20KM button：Speed shortcut key, it is valid when the treadmill is running, then press
the button to adjust the speed quickly.
L. “▲”“▼”: CUSHION ADJUST BUTTON: it can adjust the running board’s cushion soft
and hard on the treadmill.
START-UP QUICKLY(MANUAL)
1、Open the power switch, attach the magnet end of the safety pulling rope to the computer.
2、 Press “START”, The treadmill belt will start moving at the minimum speed (1km/hour)
after 3 seconds later and the buzzer will make some sounds.
3、When start the machine, you can press “SPEED UP” “SPEED DOWN” or speed shortcut
key to adjust the speed, and press “INCLINE UP” “INCLINE DOWN” or incline shortcut
key to adjust the incline.

- -
ENTERTAINER
13
The operation of exercise process:
1、Press speed-down will reduce the running speed.
2、Press speed-up will increase the running speed.
3、Press incline-down will reduce the incline.
4、Press incline-up will increase the incline.
5、Press speed shortcut key will adjust to the relevant speed directly.
6、Press incline shortcut key will adjust to the relevant incline directly.
7、Press START/PAUSE will slow down until it stops.
8、Press POWER button can stop the treadmill.
9、When the user holds the hand pulse about 5 seconds, it will display pulse data.
10、When opening the power, link the MP3 frequency output line to the computer’s frequency
input window, then the user can enjoy music, also can link the earphone line to the
computer’s frequency output window to enjoy music.
Manual mode:
1. If you do not make any setting and press START button directly, the treadmill will start to
run from the speed 1.0km/h and incline 0 level, other windows will start to count from
positive direction from windows default, press“INCLINE+/-”“SPEED+/-”or shortcut key
to change the speed and incline.
2. To set up the Time, press SELECT button one time, the TIME window will display 15:00
and flash. Press “INCLINE+/-” “SPEED+/-” to set up the time what you need. The setting
range is 5:00-99:00.
3. To set up the Distance, press SELECT button one time, the DISTANCE window will
display 1.0 and flash.. Press “INCLINE+/-” “SPEED+/-” to set up the distance what you
need. The setting range is 0.5-99.
4. To set up the Calories, press SELECT button one time, the CAL/PULSE window will
display 50 and flash.. Press “INCLINE+/-” “SPEED+/-” to set up the calories what you
need. The setting range is 10-999.
5. When setting is finished, press “ENTER” button to confirm and press START button, the
treadmill will run after 3 seconds, press “INCLINE+/-”,”SPEED+/-“ or shortcut key to adjust
the speed and the incline; press the STOP, the treadmill will stop.
Inner install program
Press“SELECT”button“TIME”window will display P1-P24, to choose the program
you like and then press“ENTER”to enter into the setting of running time, then the TIME
window display flashes. Display the advance setting time10:00, press “INCLINE”
“SPEED” to set up the exercise time what you need. Press ENTER to enter into the

- -
ENTERTAINER
14
machine is not running and press “START/STOP” button to start the inner install program,
the inner install program is divided into 20 sect. Each exercise time=the setting time/20.
When the system enters into the next sect will make 3 sounds “B—B—“ and the speed
and incline will be changed according to the setting program, then press “INCLINE”
“SPEED” or shortcut key to change the SPEED and the INCLINE, When the program
enters into next sect will come back to the current speed and incline, and run the one
program, the system will make 10 sound “B—B—“ and change to the manual program
automatically the incline is for 0 and the speed reduces to the lowest 1.0/km/h, then
“TIME” window will come back to the actual running time to positive direction to count.
Program exercise chart:
SPEED，INCLINE（Divided into 20 inclines and each incline is the 1/20 of the general
incline）. Each program will divide into 20 grades for the exercise time and each time sect
has the speed and incline accordingly.

- -
ENTERTAINER
15
1234567891011121314151617181920
SPEED 2 3 456543212345654321
INCLINE 0 0 000000000000000000
SPEED 2 4 686644222468664422
INCLINE 0 0 000000000000000000
SPEED 2 4 6 8 10 8 6 4 2 2 24681086422
INCLINE 0 0 000000000000000000
SPEED 2 2 6 6 8 10 6 6 2 2 22668106622
INCLINE 0 0 000000000000000000
SPEED 2 3 452345322345234532
INCLINE 0 0 000000000000000000
SPEED 2 4 624624622462462462
INCLINE 0 0 000000000000000000
SPEED 1 3 456543211345654321
INCLINE 0 0 000000000000000000
SPEED 1 4 686644221468664422
INCLINE 0 0 000000000000000000
SPEED 1 4 6 8 10 8 6 4 2 2 14681086422
INCLINE 0 0 000000000000000000
SPEED 1 2 6 6 8 10 6 6 2 2 12668106622
INCLINE 1 2 121211201212121120
SPEED 1 3 452345321345234532
INCLINE 1 1 234432101123443210
SPEED 1 4 624624621462462462
INCLINE 1 3 5 7 9 11 9 7 5 3 13579119753
SPEED 2 3 456543212345654321
INCLINE 2 6 6 8 10 8 6 6 2 2 26681086622
SPEED 2 4 686644222468664422
INCLINE 2 3 452345432345234543
SPEED 2 4 6 8 10 8 6 4 2 2 24681086422
INCLINE 2 4 624624622462462462
SPEED 2 2 6 6 8 10 6 6 2 2 22668106622
INCLINE 1 3 121211201312121120
SPEED 2 3 452345322345234532
INCLINE 1 2 234432101223443210
SPEED 2 4 624624622462462462
INCLINE 1 4 5 7 9 11 9 7 5 3 14579119753
SPEED 1 3 456543211345654321
INCLINE 2 5 6 8 10 8 6 6 2 2 25681086622
SPEED 1 4 686644221468664422
INCLINE 2 4 452345432445234543
SPEED 1 4 6 8 10 8 6 4 2 2 14681086422
INCLINE 2 3 624624622362462462
TIME INTERVAL
P7
P8
P9
MODE
P12
P13
P14
P19
P15
P16
P20
P21
P10
P11
P1
P2
P3
P4
P5
P6
P17
P18

- -
ENTERTAINER
16
RANGE OF PROGRAM
SETTING
PARAMETER BEGIN BEGIN TO SET UP SET UP RANGE DISPLAY RANGE
TIME（MINUTE：
SECOND） 0:00 15:00 5:00-99:00 0:00－99:59
INCLINE（LEVEL） 0 0 0-20 0-20
SPEED（KM/H） 1.0 1.0 1.0－20.0 1.0－20.0
DISTANCE（KM）0 1.0 0.5-99 0.00－99.9
HANDPULSE
（TIMES/MINUTE
）
P
N/A
N/A 60-200
CALORIES(THER
M) 0 50 10-999 0－999
SAFETY LOCK FUNCTION:
Pull out the safety pulling rope, then the treadmill will stop immediately. All the windows
display“―――”，the buzzer will make a“BB”sound ceaselessly. Then the other button
is no use except closing the machine. Attach the magnet end of the safety pulling rope to
the computer; the treadmill will be at the beginning of running.
Close up:
1. Close up the power: You can close up the power to stop the treadmill; it won’t be damaged
at any time.
2.Press the POWER button to close up: You can press the power button to stop the
treadmill, when you press the power button again, the treadmill will be awaiting orders.
CAUTION:
1. We recommend that you maintain a slow speed at the beginning of a session and hold on
to the handrails until you become comfortable and familiar with the treadmill.
2. Attach the magnet end of the safety pulling rope to the computer and also attach the clip
of the safety pulling rope to your clothing.
3. To end your workout safely, press the STOP button or pull out the safety pulling rope,
then the treadmill will stop immediately.
MULTIMEDIA DISPLAY OPERATION EXPLANATION:
SPEED 2 3 367746746744423442
INCLINE 4 5 556667899 9101010121286 3
SPEED 2 4 477478489944456332
INCLINE 5 5 566644665588999742
SPEED 2 4 567546886654424433
INCLINE 5 6 66758844455881010863
P24
P22
P23

- -
ENTERTAINER
17
Button explanation：The system has 8 control buttons, they are:“SD/AV”、 “ ”、 “ ”、
“/ENTER”、 “STOP/ESC”、 “▼”、“▲”、“ ”。
1、When you open the computer, TFT display as follows:
PICTURE1
2、Put the memory card（SD/MMC）into the memory card’s electrical outlet of the machine.
3、With the direction button“ ”、 “ ”、 to choose “VIDEO”、“MUSIC”or“PHOTO”
of the picture 1. Press“/ENTER”to confirm your choice.
4、If you choose“VIDEO”，press“/ENTER”to confirm, then the machine will enter into
the “VIDEO”files，with the direction left right up down button to choose what you need the
“VIDEO” file displays. Then press“/ENTER”to proceed full screen display. Press
“STOP/ESC”button can back to the last menu, the final stair menu as picture 1.
5、If you choose“MUSIC”，press“/ENTER”to confirm, then the machine will enter into
the“MUSIC”files，with the direction left right up down to choose what you need the“MUSIC”
file display. Press“STOP/ESC”button can return back the last menu, the final stair menu
as picture 1.
6、If you choose“PHOTO”，press“/ENTER”to confirm, then the machine will enter
into the“PHOTO”files，press“STOP/ESC”button can stop the picture display and enter
into the picture list (then press“STOP/ESC”button can back to the final stair menu as
picture 1), with the direction left right up down button can choose the “PHOTO” you like,
press“/ENTER”button can proceed the full screen display. Press the direction up down
left right button can see the picture from different angles when it on the full screen display.
7、Press“SD/AV”button can enter into“AV IN”status, then connect the signal, TFT display
will show; Then press“SD/AV”button can back to the menu 1（AV OUT status）.
8、“ ” power supply button: it uses for cutting off the power supply of the video system.
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
PROBLEM CAUSE CHECKING CORRECTION
1.If the plug and the line is
loosen.
1. Checking the plug and
the line is connected well.
1.Insert the plug and the line
well.
Treadmill
will not
start. 2.Not plugged in. 2. Checking the power 2.Reset the power.

- -
ENTERTAINER
18
switch is opened.
1. The relative line of the
control motor are abnormal.
1. Checking the line of the
control motor is plugged
well.
1. Insert the control motor wire.
2.Do not press START KEY.
2.Checking the button is
valid or not started the
switch ?.
2.Reset the START KEY to
test.
3.Safety pull pin not inserted 3.Checking the safety pull
pin is plugged well. 3.Insert safety pull pin.
4.Motor plug is loosen or the
motor is faulty.
4.Testing if the motor is
faulty. 4.Change the motor
The motor
will not
work.
5.Power or controller
specification is wrong.AC
（220~240）V
5.Checking the
specification.
5.To choose the correct
specification to reset the
testing.
1.Checking the distance
and place between
SENSOR and magnet.
1.Adjust the distance within
5m/m.
2.Checking the wire if
circuit breaker tripped. 2.Change the wire or SENSOR
No speed SENSOR does not touch
well.
3.Checking the wire tie-in
if it is touched well. 3.Reset to insert the wire tie-in.
PA circuit
board
Pa circuit board bolt does not
lock well or not put the
connector well.
Take apart the bottom
cover and press PA circuit
board to see if it is short
circuit or loosen.
Reset to put the connector?
and lock the bolt.
1.Checking the wire is
short circuit or loosen. 1.Change the wire or reset.
SENSOR does not touch
well. 2.Checking the wire and
computer if the tie-in is
connected well.
2.Reset to insert the wire
No hand
pulse
The hand pulse does not
touch well
3.Put both hands to bedew
a little or scrub with both
hands.
3.Reset to test.
E01 Message failure 1.the connected wire is
wrong.
1.Use the multimeter to test the
wire is stand or fall.

- -
ENTERTAINER
19
2.To test the outside and the
inside voltage is normal.
（DC12V）
2.Power supply voltage is
of shortage
3. SCM is badness.
1．Power tube is faulty 1．Change the power tube
2．Drivers is faulty 2．Change the drivers
E02 burst clash
3．Motor is failure 3．Change the motor
1.Sensor wire is faulty. 1．Change the sensor wire
2．It is no use for the motor
magnetic.
2．Change the magnetic or
reset the magnetic
E03 No sensor signal
3．Drivers is faulty. 3．Change the drivers
1．Study failure 1．To reset study
2. Incline motor is faulty. 2．Change the incline motor
3．Drivers is faulty. 3．Change 24C02 or change
the drivers
E04 Incline study failure
4．Incline motor wire do not
connect well 4．Insert the incline motor wire.
1．The limited weight 1．Do not exceed the treadmill
user’s maximum weight.
2．Drivers in badness 2．Change the limit resistance
or change the drivers
E05 Over loading protector
3．Voltage is wrong 3．Test the usage voltage is
measure up
1．The machine is
interfered 1．Reset the treadmill
E06 System testing failure
2．Drivers badness 2．Change IGBT or change
drivers.
1．Safety lock badness 1．Change the safety lock
E07 Out of safety lock
2．Computer badness
2．Test the iron piece of the
safety lock is dropped out or
change the computer.
E08 24C02 message failure 1．Data transfer failure 1．Change 24C02 EEPROM
IC