LIFEPLUS GD9315BCW-3J Operating manual
Thank you for choosing a heater. This owner's
manual will provide you with valuable information
necessary for the proper care and maintenance
of your new product. Please take a few
minutes to read it.
IMPORTANT INSTRUCTIONS PAGES 3-5
INTRODUCTION
SECTION 1
TIP-OVER SAFETY FEATURE PAGES 6
OVERHEAT SAFETY FEATURE PAGES 6
SECTION 2
PRODUCT DIAGRAM PAGES 6
CONTROL PANEL PAGES 7
REMOTE CONTROL PAGES 8
SECTION 3
PREPARATION PAGES 8
SECTION 4
MAINTENANCE PAGES 11-12
TROUBLESHOOTING PAGES 13
SECTION 5
STORAGE PAGES 13
IN THE BOX
WARRANTY
PAGES 13
PAGES 14
SECTION 6
TABLE OF CONTENTS
OPERATING INSTRUCTION PAGES 9-11
TECHNICAL PARAMETERS PAGES 5
When using this electric unit, basic safety precautions should always be followed to reduce
the risk of fire, electric shock, and injury to persons, including the following:
(1). Read ALL instructions before using this unit.
(2). CAUTION: Risk of Electric Shock. DO NOT open or try to repair the heater yourself.
(3). This heater may get hot when in use. To avoid burns, DO NOT let bare skin touch hot
surfaces. If provided, use handles when moving this heater.
(4). Keep combustible materials, such as furniture, pillows, bedding, paper, clothes, and
curtains at least 3 ft from the front of the heater and keep them away from the sides, top,
and rear. DO NOT place towels or other objects on the heater.
(5). Extreme caution is necessary when any heater is used by or near children or the
disabled, or when the heater is left operating and unattended.
(6). DO NOT operate any heater with a damaged cord or after the heater malfunctions,
has been dropped or damaged in any manner. Return heater to authorized service facility
for examination, electrical or mechanical adjustment, or repair.
(7). This heater is not intended for use in bathrooms, laundry areas and similar indoor
locations. NEVER locate heater where it may fall into a bathtub or other water container.
To protect against electrical hazards, DO NOT immerse in water or other liquids.
(8). DO NOT touch the control panel or plug with a wet hand.
(9). DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or
similar coverings. Arrange cord away from traffic area and where it will not be tripped over.
(10). DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as
this may cause an electric shock or fire, or damage the heater.
(11). To prevent a possible fire, DO NOT block the air intakes or exhaust in any manner.
DO NOT use on soft surfaces, like a bed, where openings may become blocked.
(12). A heater has hot and arcing or sparking parts inside. DO NOT use in areas where
gasoline, paint, explosive and/or flammable liquids are used or stored. Keep unit away
from heated surfaces and open flames.
(13). Always plug heaters directly into a wall outlet/receptacle. Never use with an extension
cord or relocatable power tap (outlet/power strip).
(14). To avoid fire or shock hazard, plug the unit directly into a 120 V AC electrical outlet.
(15). To disconnect heater, turn controls to OFF, then remove plug from outlet. Pull firmly
on the plug, DO NOT unplug by pulling on the cord.
(16). Always unplug the unit before moving or cleaning, or whenever the heater is not in
use.
(17). Use only for intended household use as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock, or injury to persons.
The use of attachments not recommended or sold by unauthorized dealers may cause
hazards.
(18). Always use on a dry, level surface. Use on floor only.
(19). DO NOT use outdoors.
(20). WARNING: To reduce the risk of fire or electric shock, DO NOT use this unit with any
solid-state speed control device.
(21). DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit.
Doing so will void your warranty. The inside of the unit contains no user serviceable parts.
Qualified personnel should perform all servicing only.
(22). Connect to properly grounded outlets only.
(23). Save these instructions.
IMPORTANT INSTRUCTIONS
!
- 3 - - 4 -
TIP-OVER SAFETY FEATURE
This heater is equipped with a shut-off safety feature. Once the heater is tipped over, an
internal switch will automatically shut the heater off. Once the heater is restored to an
upright position, the heater will reset.
OVERHEAT SAFETY FEATURE
This heater is equipped with a overheat safety feature. When the heaters internal
components reach a certain temperature that could cause overheat and possible fire,
the heater will automatically shut off.
PRODUCT DIAGRAM
WARNING:
This heater has a voltage rating of 120 volts. The cord has
a plug as shown in A. An adapter as shown in C is available
for connecting three-blade grounding-type plugs to two-slot
receptacles. The grounding lug extending from the adapter
must be connected to a permanent ground such as a
properly grounded outlet box. The adapter should not be
used if a three-slot grounded receptacle is available.
DO NOT DEFEAT THE SAFETY PURPOSE OF THE
GROUNDED PLUG.
TECHNICAL PARAMETERS
Model No.
Item Name Infrared Heater
GD9315BCW-3J
Rated Voltage
Rated Power
Three Setting
Safy Protection
Net Weight
Gross Weight
Product Size
1500W
120V (60Hz)
Tip-Over & Overheat Protection
Low / High / ECO
19.62 LBS
12.8 x 10.83 x 14.76 inch
16.1 LBS
- 5 - - 6 -
Air
Outlet
Air
Intake
Cord
Clamp
Power
Switch
Wooden
Cabinet
Remote
Control
Control
Panel
Temp Sensor
CONTROL PANEL
1. Signal receiving window: For receiving remote control signal.
2. Digital display: Indicate set room temperature or time
3. Power indicator light: Indicators that the heater is receiving power from outlet.
Will flash when powered "ON"
4. ON/OFF button: Powers the display on and off.
5. Energy-saving mode indicator: Will be lit when energy-saving mode is engaged.
6. Mode button: To select between High, Low and Eco modes.
7. Low Mode indicator light: Will be lit when Low Heat mode is engaged.
8.Temp up button: To increase desired temperature.
9. High Mode indicator light: Will be lit when High Heat mode is engaged.
10.Temp down button: To decrease desired temperature.
11. Timer indication light: Will be lit when the Timer mode is engaged.
12. Timer button: Used to engage timer mode and to set hour value for the timer.
13. Fahrenheit indicator light: Will be lit when temperature displayed is in Fahrenheit.
14. ℃/℉Button: Alternates between Fahrenheit and Celsius.
15. Celsius indicator light: Will be lit when temperature displayed is in Celsius.
- 7 - - 8 -
PREPARATION
Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet.
and turn on the power switch in the rear of the unit. Only operate heater in upright position.
Insert 2 AAA batteries into the remote control before using (Batteries Not Included).
At first startup, there may be a strange smell, which is caused by the evaporation of the
coating used to protect the metal inside the product. It is a non-toxic gas that will dissipate
after running for a period of time. If you cannot accept this odor, you can use it outside the
door for 15 minutes before entering the house.
REMOTE CONTROL
ON/OFF Button:
Used for power-on or power-off
Temp Down Button:
To make set temperature decline
Mode Button:
Used for mode selection
Timer Button:
Used for setting timer and adjust time value of timing
℃/℉ Button:
Button for alternating between Fahrenheit and Celsius
Temp Up Button:
To make set temperature rise
1
1
6
12 11
2
2
14
15
13
33
44
10 98 7 65
5
1
2
3
4
5
6
1. Remote Control
Press the MODE button to toggle between the three heat modes.
2. Control Panel
High Mode uses 1500W; Low Mode uses 750W. ECO mode is an
Economic Energy Saving Function. When ECO mode is chosen, the
heater will manage itself from less to more heating power (watts) in
an attempt to maintain a constant warm 68℉(20℃)
Adjust the desired temperature by pressing the Up/Down arrows on
the control panel or remote control.
Desired temperature options vary from 59℉to 86℉, or from 15℃to
30℃. Once you have chosen the desired temperature, the heater will
remain on until the room temperature increases to the temperature
on the digital display. The heater will cycle on and off to maintain the
desired room temperature.
- 9 - - 10 -
Press ℃/℉ button to change the display temperature between
Fahrenheit and Celsius.
The Fahrenheit indicator LED will light , when the temperature is
displayed in Fahrenheit.）
The Celsius LED will light, when the temperature is displayed in
Celsius.
OPERATING INSTRUCTION
1. Plug in the power cord and power on button
2. Select working mode and setting desired temperature
Control
Panel
Remote
Control
Open the power
1. When you want to use the heater, please press power button "I" first.
2. When do not use it, please press power button " O " first.
Turn the heater on by pressing the ON/OFF button on the control panel
or by pressing the Power button on the supplied remote control.
Once power is off, heating element will stop working at first. Fan will
prolong working for 3 min to emit plenty of heat inside. This mark will
indicate running during the 3 min.
l
0
3. Setting the POWER OFF/ON TIMER Function
Note: (1). The Power-Off-Timer Function will allow for the heater to power OFF after a
certain set time, and can only be set while the heater display is in the “On” position
(2). The Power-ON-Timer Function will allow for the heater to power ON after a certain
set time, and can only be set while the heater display is in the “Off” position.
1. Turn the heater to the “On” position .Press the Timer button on
the heater’s control panel or the remote.
2. Turn the heater to the “OFF” position .Press the Timer button on
the heater’s control panel or the remote.
The digital display changes from the "temperature" to the "hours"
option for the timer. Continue to press the timer button to change the
number of hours you would like the heater to run before powering
itself off .The hour options for the timer are from 0 to 12 hrs.
(in 1 hr increments).
The selected hour increments will flash for a few seconds, then
revert back to the set desired temperature .The Timer indicator light
will remain lit as long as the Timer is set. The heater will power OFF
when the internal heater clock counts down the hour increments you
set.
or
or
or
or
or
or
or
MAINTENANCE
PUSH
1. Turn off the power switch in the rear of the unit.
2. Unplug the unit and let it cool completely.
3. To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You
may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth.
CAUTION: DO NOT let liquid enter the heater.
4. DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to
clean the heater. This may cause damage or deterioration to the surface of the heater.
5. DO NOT immerse the heater in water.
6. Wait until the unit is completely dry before use.
7. Air filter needs cleaning after used 3 months of use. Please take off the filter with the 2
steps in the drawing below. Flush and clean the filter with water, Then, dry it out and
re-assemble.
- 11 - - 12 -
4. Setting electro lock
The Electro Lock can help avoid the heater from being accidentally engaged by children.
The locking mechanism can be set in both the ON and OFF modes.
* If you do not use the heater for a long time, please take out the remote batteries (to
prevent corrosion ) as shown below. Store the remote in a safe place.
The Unit Remove Air Filter
Remove Bracket Screws (4X)
Lid Battery
Press Temp Up and Temp Down buttons at the same time for 3
seconds. Locking is complete when you hear a beep. When locked,
the functions of the control panel and remote will be locked for use.
When you need to unlock it, press Temp Up and Temp Down buttons
at the same time for 3 seconds. You will hear a beep .The control
panel and remote control will become functional again.
or
and
INFRARED HEATER INSTRUCTION
BOOKLET
REMOTE CONTROL
(2 AAA Batteries Not Included)
- 13 - - 14 -
TROUBLESHOOTING
If the heater will not operate, please check the following before seeking repair advice:
1.Check if the power cord is plugged into an electrical outlet, if not, plug in.
2.Check if electricity to the main power switch (in the back) is working.
3.Check to see if the battery on the remote is placed correctly, undamaged.
NOTE: For the heater to function properly, the desired temperature on the heater must be
set a few degrees higher than the temperature in the room. If the seems to not be heating,
increase the desired temperature on the heater to engage the heat elements.
STORAGE
IN THE BOX
Store the heater in a cool, dry location when not in use. To prevent dust and dirt build-up,
use the original packaging to repack the unit.
INFRARED HEATER
PRODUCT USE GUIDE
GD9315BCW-3J
WARRANTY
After-sales Service Letter of Commitment
All products purchased in our company are guaranteed to keep in good repair for 1 year
If quality problems happen in guarantee period, our company will maintain for free or
provide replacement. Additionally, our company provides technical support and fittings
for life. After-sales service isn't restricted by time and hear feedback idea of users and
deal with them in time. If you are caught in some problems when using our products,
welcome to contact us at any time.
Table of contents
Other LIFEPLUS Heater manuals
