LifeSafety Power ADC-AC-X1100-2PSE User manual

Description
The ADC-AC-X1100-2PSE is a two door access control unit
featuring dual voltage power and includes one prewired
X1100. The 14”x 12”x 4.5” metal enclosure includes battery
space.
Equipment List
1. Pre installed AC power cord
2. Power Supply 24VDC / 3A (model: FPV4)
3. Secondary 12V supply (model: B100)
4. Pre-installed X1100 controller
Accessories included
• AC power cord
• Battery harness



QUICK GUIDE ADC-AC-X1100-2PSE
1/2 www.lifesafetypower.com
System Operation
The FPV4 power supply converts AC primary power to 24VDC for charging the battery set and powering the X1100 con-
troller, B100, locking device(s), and 24V auxiliary devices. The B100 is powered from the FPV4 Auxiliary terminals and
steps the 24V down to 12V to power any 12V auxiliary devices.
The battery set is charged by the red/black harness on the bottom edge of the FPV4. The battery set MUST be two 12V
batteries in series for a 24V battery set. Observe polarity or damage to the system will occur.
Positive lock power is prewired to the X1100 lock relay Common terminals. The lock positive should be wired to the NC
(Fail Safe) or NO (Fail Secure) terminal as appropriate. Each lock negative should be wired directly to the FPV (-) terminal
to minimize noise and surges in the system.
September 2020
Terminal Output Ratings
**Max currents listed are for individual terminals - total current at 12V and 24V not to exceed max rating of supply
Board Terminal Voltage Max Current** Notes
FPV4 DC OUT 24V 1.5A Output can be switched by FAI Input on FPV4
AUX OUT 24V 0.75A Max Current includes current drawn by B100
B100
DC OUT 12V 1.5A For additional 12V devices
J2 (DC OUT) 12V 1.5A For additional 12V devices
J5 (DC OUT) 12V 1.5A For additional 12V devices
J1 (DC IN) 24V 0.75A For additional 24V devices
J4 (DC IN) 24V 0.75A For additional 24V devices
X1100 OUT1 (NO or NC) 24V 1.5A Switched Lock Output - Ground at FPV4 (-) Terminal
OUT3 (NO or NC 24V 1.5A Switched Lock Output - Ground at FPV4 (-) Terminal
090920_rev1

LifeSafety Power
899 E Park Avenue
Libertyville, IL 60048 USA
www.lifesafetypower.com
Tel [phone]
[e-mail]
Important: All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate
the suitability of each product for their particular application. LifeSafety Power makes no warranties as to the accuracy or
completeness of the information, and disclaims any liability regarding its use. LifeSafety Power’s only obligations are those
in the LifeSafety Power Standard Terms and Conditions of Sale for this product, and in no case will LifeSafety Power or its
distributors be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of
the product. Specifications are subject to change without notice. In addition, LifeSafety Power reserves the right to make
changes—without notification to Buyer—to processing or materials that do not affect compliance with any applicable specification.
ADC-AC-X1100-2PSE QUICK GUIDE 2
September 2020 2/2 www.lifesafetypower.com
DC OUT
BR BR
DC IN
DC OUT
DC IN
FAULT
DC IN
DC OUT
+
–
B100
24 to 12V converter
12V
Battery
- +
12V
Battery
- +
DC OUT Terminals
may be used for
24V Aux Power
Cabinet
Tamper
Switch
Tamp+
Tamp-
ACF+
ACF-
Bat+
Bat-
Ground
+12-24VDC
Reader Power
Ground
Data0/Data
Data1/Clock
Ground
Green LED
Red LED
Beeper
Reader Power
Ground
Data0/Data
Data1/Clock
Ground
Green LED
Red LED
Beeper
Ground
In1+
In1-
In2+
In2-
NO
C
NC
NO
C
NC
Out1
Out2
Ground
In3+
In3-
In4+
In4-
NO
C
NC
NO
C
NC
Out3
Out4
Micro USB
Ethernet
X1100
TR+ TR-
Ground
TR+ TR-
Ground
Port 1 Port 2
IO Modules
Locking
Device 1
+
-
Connect Locks to either
NO or NC based on type
of lock and system requirements
Locking
Device 2
+
-
Attach AC Line cord to
FPV4 AC Input Terminals
12VDC
24VDC 24VDC
B100 Screw Terminals
May be used for
12V Aux Power
i
Power Supply voltage
factory pre-set for 24V
NO NOT CHANGE!
L L V- I- I+ V+ NC NC
NO NOC C _+
BATTERY
24VDC
FPV4
24V
+
+
24V PS/Charger
L N
AC ON
FAI
MAIN
DC
AUX
SYS FLT AC FLT
FAI INPUT
Wiring Diagram