Lifetime 0023 Quick start guide

1
®
3/19/2012
VISIT THE LIFETIME WEB SITE:
WWW.LIFETIME.COM
3.5” GROUND SLEEVE
MODEL #0023
ASSEMBLY INSTRUCTIONS
AND OWNER’S MANUAL
WARNING
To ensure your safety, do not attempt to assemble this system
without reading and following all instructions carefully. Identify and
inventory the parts using the Parts List. Failure to comply with any
of the warnings in these instructions may result in serious personal
injuries such as cuts, broken bones, nerve damage, paralysis, brain
injury, or death. Failure to comply may also result in property damage.
Please heed all warnings and cautions.
INSTRUCTION #1019201 C
**U.S. and Canada customers ONLY**
IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!!!
CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 [phone]
HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
**Call, or visit our Web site for Saturday hours**
**For customers outside the U.S. or Canada, please contact the store for assistance.**
TOOLS AND MATERIALS REQUIRED
FOR ASSEMBLY
1. Concrete (Six 90-lb. bags)
2. Water Supply
3. Wheelbarrow
4. Shovel
5. Carpenter’s Level
6. 9/16” Wrench
7. Funnel
8. Pencil or Marker
9. Tape Measure
Save this instruction in the event that the manufacturer has to be contacted for replacement parts.
Register your product online at www.lifetime.com.
Lifetime’s Promise to You:
Maintaining your privacy is our long-standing policy at Lifetime. And you can rest assured that Lifetime will not sell or
provide your personal data to other third parties, or allow them to use your personal data for their own purposes.
We invite you to read our privacy policy at www.lifetime.com
REGISTER today!
At Lifetime, we are committed to providing innovative and quality products. While registering, you will have the opportunity
to give us your feedback. Your input is valuable to us.
You can also opt-in to receive new product notifications or promotions.
In the unlikely event of a product recall or safety modification, your registration provides the information we need to
notify you directly.
Registration is fast, easy, and completely voluntary.
COPY

2
PARTS LIST
ID Part # Description Qty
AA 1018892 Ground Sleeve 1
Hardware (HD9039)
AB 300111 3/8” x 3/4” Hex Bolt 1
AC 500058 Plastic Cap 2
AD 800051 Locking Tab 1
HARDWARE IS ACTUAL SIZE
AB
BEFORE BEGINNING
ASSEMBLY
A. If any parts are missing, call our Customer Service
Department.
B. Test fit all Bolts by inserting them into their respective holes.
If necessary, carefully scrape away any excess powder
coating buildup from inside the holes. Do not scrape away
all of the powder coating. Bare metal may rust.
NOTE: This Ground Sleeve is for use with in-ground poles
only. The Bottom Pole section is not included with this
product. Use the Bottom Pole section from your purchased
Lifetime®system.
a. Insert the dimpled end of the Bottom Pole into the
Ground Sleeve (AA). Make sure the Bottom Pole
section fits completely into the Ground Sleeve.
b. Tap the pole and ground sleeve lightly on the ground
so they stay together during the cementing steps.
STEP 1 STEP 2
a. Insert the 3/8” x 3/4” Hex Bolt (AB) into the
hole of the Locking Tab (AD) and screw the
Bolt in until the end of the Bolt is flush with
the edge of the Tab.
b. Push the Locking Tab assembly into the slot
in the top of the Ground Sleeve as shown.
Push the Locking Tab in as far as it will go.
c. Tighten the Bolt just enough to hold the
Bottom Pole section in position. DO NOT
OVERTIGHTEN. The Bolt will be removed
later in the installation.
d. Place a Plastic Cap (AC) over the lower end
of the Ground Sleeve to prevent cement
from seeping in.
AD
AC
AB
AD
SAFETY INSTRUCTIONS
Most injuries are caused by misuse and/or not following instructions. Use caution when using this system.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or
additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document. Proper
and complete assembly, use and supervision are essential for proper orientation and to reduce the risk of accident or injury. A high probability of serious injury exists if
this system is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
t*GVTJOHBMBEEFSEVSJOHBTTFNCMZVTFFYUSFNFDBVUJPO
t5XPDBQBCMFBEVMUTBSFSFDPNNFOEFEGPSUIJTPQFSBUJPO
t"TTFNCMFUIFQPMFTFDUJPOTQSPQFSMZJGBQQMJDBCMF'BJMVSFUPEPTPDPVMEDBVTFUIFQPMFTFDUJPOTUPTFQBSBUFEVSJOHQMBZ
t#FGPSFEJHHJOHDPOUBDUVUJMJUZDPNQBOZUPMPDBUFVOEFSHSPVOEQPXFSDBCMFTHBTBOEXBUFSMJOFT&OTVSFUIBUUIFSFBSFOPPWFSIFBE
power lines within 20 ft. (7m) radius of pole location.
AB
Bottom
Pole
dimples
AA
COPY

3
a. Dig a round hole 24” deep and 18” in diameter.
b. Mix all 6 bags of concrete, except 1/3 of a bag which will
be used later to fill the inside of the Bottom Pole section.
c. Fill the hole half full with concrete. Insert the Ground Sleeve
and Bottom Pole section into the cement. The correct
distance from the basketball court to the front of the pole
is 4 inches. The top of the Ground Sleeve should be flush
with the basketball court. The Hex Bolt and Locking Tab
must face away from the basketball court.
1ST POURING
2nd POURING
STEP 3
a. Using a level, check the pole several times within the
first hour to make sure all sides are vertical. Readjust
the pole if necessary before the concrete begins to firm.
b. Be sure the inner edges of the Ground Sleeve are free
of concrete.
CAUTION: Allow at least four hours for the concrete
to set up before continuing assembly.
STEP 4
STEP 5
a. Loosen the Bolt and remove the Locking Tab
from the Ground Sleeve. Carefully remove the
Bottom Pole section from the Ground Sleeve.
b. Place the other Plastic Cap (AC) over the lower
end of the Bottom Pole section.
c. Mix the remaining 1/3 bag of concrete. Using
a funnel, pour the concrete into the Bottom
Pole section until it is just below the slot in the
top of the pole. Leave the pole standing in an
upright position until the concrete sets.
a. Remove the Plastic Cap from the
Bottom Pole section and discard.
b. Measure 14 1/2” up from the bottom
of the Bottom Pole section and make
a mark on the Pole. Insert the Bottom
Pole section into the Ground Sleeve,
making sure that the 14 1/2” mark
reaches the top edge of the Ground
Sleeve. Refere to the manufacturer’s
instructions for pole alignment.
c. Install the Locking Tab so the Bolt
touches the rim of the Ground Sleeve.
d. Tighten the Locking Bolt securely with
an open end wrench to prevent the pole
from rotating. Do not overtighten the Bolt
or the Locking Tab may be damaged.
WARNING: The Bottom Pole section
must be inserted 14 1/2” into the
Ground Sleeve. The dimples on the
Bottom Pole are for identification
purposes only. If the Bottom Pole
section does not fit, check the bottom
of the Ground Sleeve for debris or
concrete. Clean out the Ground
Sleeve and reinstall the Bottom Pole
section.
STEP 6
AC
Continue with Step 7 on the next page.
18”
24”
PLAYING
SURFACE
4”
d. Finish filling the hole with
concrete. Make sure the
Ground Sleeve is flush with
the basketball court and is
not sunk into or positioned
above the concrete.
e. Form the concrete into
a downward slope, away
from the Ground Sleeve.
This will allow any water
buildup to flow away from
the Ground Sleeve. Failure
to do so may result in
premature rusting of the
Ground Sleeve.

4
a. Allow the concrete to set
for at least 72 hours.
b. Follow the manufacturer’s
instructions to complete
the installation of your
system.
STEP 7
PRODUCT DESCRIPTION MODEL #
Pole Pad 0600
This heavy-duty foam pad is
covered with tough vinyl. Protects
players from impact with the pole.
TO PLACE ORDERS, USE A MASTER
CARD
OR VISA AND CALL OUR CUSTOMER
SERVICE DEPARTMENT
ACCESSORIES AVAILABLE FOR MORE
BASKETBALL FUN!
For Price and Shipping costs call our
Customer Service Department.
LIFETIME BASKETBALL EQUIPMENT
5-YEAR LIMITED FACTORY WARRANTY
THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE
OR OBSOLETE.
1. Lifetime basketball systems are warranted to the original purchaser to be free from defects in material or workmanship for a period
of five years from the date of original retail purchase. The word “defects” is defined as imperfections that impair the use of the product.
Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper
installation, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other
event beyond the control of the manufacturer.
2. This warranty is nontransferable and is expressly limited to the repair or replacement of defective basketball equipment. If the equipment
is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser.
Shipping charges to and from the factory are not covered and are the responsibility of the purchaser. Labor charges and related expenses
for removal, installation or replacement of the basketball system or its components are not covered under this warranty.
3. This warranty does not cover scratching or scuffing of the product that may result from normal usage. In addition, defects resulting
from intentional damage, negligence, unreasonable use or hanging from the net or rim will void this warranty.
4. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody
the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting
from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change
this policy.
5. This product is not intended for institutional or commercial use; Lifetime Products, Inc. does not assume any liability for such use. Institutional
or commercial use will void the warranty.
6. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability or fitness for
use. Neither Lifetime Products, Inc., nor any representative assumes any other liability in connection with this product.
ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT.
To register the product, visit our Web site at www.lifetime.com
REPORT PRODUCT DEFECTS IN WRITING TO:
Lifetime Products, Inc., PO Box 160010 Clearfield, UT 84016-0010 or
call [phone] M-F 8 a.m. to 5 p.m. MST.
Please include your dated sales receipt and photographs of damaged parts.
POLE PAD