Lightronics FXLD2512B5I6 User manual

Page 1 of 6
FXLD2512B5I6 LED FIXTURE
Version 1.0 OWNERS MANUAL 05/07/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
FEATURES AND SPECIFICATIONS
LEDS: 12, 25W each (RGBWA, 5in1)
Beam angle: 60°
Control system: DMX512 + Stand Alone Modes
DMX channels: 5/9
DMX connectors: 3 pin XLR I/O
Refresh Rate: >3000 Hz
Voltage: 100 - 240 VAC 50/60Hz
Max power consumption: 330 Watts
Cooling: Intelligent Fan
Body material: Sheet steel
Body color: Black
Size: 39.4"L x 5"W x 3.4"H
DESCRIPTION
The FXLD2512B5I6 is an RGBWA LED lighting fixture. It
is suitable for stage, houses of worship, entertainment
venues, and other artistic applications. It has several stand-
alone control modes and can operate via a DMX512 external
signal.
INSTALLATION
LOCATION
The FXLD2512B5I6 is rated IP20 and is intended for
INDOOR USE ONLY.
Locate the unit in a well ventilated area away from moisture
and heat. Keep the vent holes clear. Holes are provided on
the brackets to install a lighting bar pipe clamp. Use a safety
cable when hanging the fixture.
POWER CONNECTIONS
The FXLD2512B5I6 has a blue turn and lock connector for
power input. A compatible power cable is provided for
connection to a 120 VAC, 15 Amp, 60Hz, grounded service.
Push the blue connector on the cable straight into the blue
connector on the unit and twist approx. 1/8 turn clockwise to
latch it. The white turn and lock connector on the unit is
used to pass power on to another FXLD2512B5I6 unit. A
mating white connector is also provided.
Caution is advised since the line cord is rated for approx. 7
Amps maximum.
THE SAFETY GROUND TERMINAL ON THE POWER
CABLE MUST BE USED.
DMX CONNECTIONS
A system using DMX control must be connected as a chain
of devices. In other words, the control signal cable should
proceed from the controller to the first receiving device and
then to others in a continuous "daisy chain" fashion.
The fixture has a DMX IN and a DMX OUT connector to be
used to connect the chain. The control cable should NOT be
split into a multiple run star arrangement with a cable
running from the controller directly to each receiving device
pack.
DMX CONNECTOR PIN ASSIGNMENTS
There are two different connectors which can be used for
DMX control. They are both XLR type connectors.
This unit uses 3 pin XLR type connectors. The
FXLD2512B5I6 receives a DMX signal on the 3 pin MALE
connector on one side of the unit. On the other side of unit,
the 3 pin FEMALE connector is used to connect to the next
DMX device on the control chain.
3 Pin Pinout
DMX TERMINATION
A DMX chain should be terminated at the last receiving
device on the chain. This is done by installing a commonly
available 1/4 Watt, 120 Ohm resistor across the DATA - and
DATA + wires at the last device. If you have only a few
fixtures very close together and a very short run to the
controller then you may be able to operate without the
terminator.
PIN #
SIGNAL NAME
1
DMX COMMON
2
DMX DATA -
3
DMX DATA +
CAUTION
RISK OF ELECTRIC SHOCK

Page 2 of 6
FXLD2512B5I6 LED FIXTURE
Version 1.0 OWNERS MANUAL 05/07/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
OPERATION
A control panel on the back of the unit is used to set the
operating options. It consists of an LED display and four
buttons (MENU, UP, DOWN, and ENTER)
Push MENU to access the operating options. Press UP or
DOWN to cycle through options. When you reach the
option you want to set or change use the ENTER button to
select the option to change. Then using the UP and DOWN
buttons to modify the values. Push ENTER to save your
changes and activate the option. See the "MENU
NAVIGATION" diagram for additional details.
There are 8 operation modes: DMX 5 channel, DMX 9
channel, Color Fade, Color Change, Color Select, Manual
Level (5 selections), Demo, and Sound.
Pressing MENU alternates to display 0XXC for current LED
plate temperature. The fan turns on at low speed when
temperature is at or above 45° C and will turn back off at or
below 34° C. The fan shifts to high speed if temperature
increases to 55° C and back to low speed once temp reaches
49° C.
DMX OPERATION
For DMX operation the FXLD2512B5I6 fixture can be
configured as a 5 channel or 9 channel unit.
Use the dXXX (5 ch) or AXXX (9 ch) menu to set the
starting address of the unit. You can select the starting
address of the unit with the UP and DOWN buttons.
Detailed information on DMX channel operation is given in
the tables DMX VALUES AND FUNCTIONS.
MANUAL OPERATION
If there is no DMX signal provided to the unit, then setting
any of these will result in the unit that was set acting as a
master. DMX signals will override all manual settings. The
unit has an LED on the menu display (decimal point). If the
LED is flashing, the unit is not receiving signal either from a
DMX controller or from a master fixture. LED will
disappear once DMX is present.
Color Fade (CFXX)
The Color Fade mode cycles smoothly through a sequence
of colors. Use the CFXX menu to set the speed and activate
the option. The range is from 00 to 99 (99 is fastest).
Color Change (CCXX)
The color change mode cycles through a variety of colors at
a user defined speed. Use the CCXX menu to set the rate of
speed at which the colors change. The range is from 00 to 99
(99 is fastest).
Color Select (CSXX)
For additional manual operations you can use the Color
Select menu CSXX to select one of 16 colors and levels.
Options from 00-99.
R, G, B, W, A Manual Level Control
You can operate the individual color levels manually using
the r000, G000, b000, E000, and Y000 menus. Use the UP
and DOWN buttons to change the level, Push ENTER when
done. The range is 000 - 255 (255 is maximum).
Demo Modem (dENo)
The unit cycles through a fixed series of colors and fades.
There are no adjustments or settings in this mode. Return to
Channel mode to exit Demo.
Sound Modem (Soun)
The unit reacts to sounds by changing colors randomly.
There are no other settings within this mode.
Sound mode can also be activated in 9 channel mode with
DMX channel 9 set to 240-255. Brightness can be controlled
with DMX channel 1 (0-255).

Page 3 of 6
FXLD2512B5I6 LED FIXTURE
Version 1.0 OWNERS MANUAL 05/07/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
Signal Response Rate (dEL0)
Provides a signal response cushion to smooth out LED
dimming operation. The dEL0 setting is for no cushion, and
dEL1, 2, 3 select available response cushion characteristics.
MAINTENANCE AND REPAIR
TROUBLESHOOTING
Check that you have power applied to the unit.
Check the DMX control cable.
Check the address settings of the unit and the controller.
CLEANING
Do not use harsh chemicals or solvents when cleaning the
fixture. A mild detergent can be used sparingly if needed.
Ensure that the unit is completely dry before re-use.
REPAIR
The fixture contains a 2 Amp 250VAC, fast acting, 5mm x
20mm externally accessible fuse. Replace the fuse ONLY
with the same size and type.
The FXLD2512B5I6 does not contain any other user
serviceable parts. Internal service on the unit by other than
Lightronics authorized agents will void the warranty.
If service is required, contact the dealer from whom you
purchased the item, or contact the Lightronics, Service
Department, 509 Central Drive, Virginia Beach, VA 23454.
Tel: [phone].
CAUTION DO NOT OPEN UNIT
RISK OF ELECTRIC SHOCK
RISK OF FIRE

Page 4 of 6
FXLD2512B5I6 LED FIXTURE
Version 1.0 OWNERS MANUAL 05/07/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
MENU NAVIGATION

Page 5 of 6
FXLD2512B5I6 LED FIXTURE
Version 1.0 OWNERS MANUAL 05/07/2019
www.lightronics.com
Lightronics Inc. 509 Central Drive, Virginia Beach, VA 23454 757 486 3588
DMX VALUES AND FUNCTIONS
5 CHANNEL MODE (MODE dXXX)
9 CHANNEL MODE (MODE AXXX)
*Channel 9 additional characteristics.
If DMX is raised to 64-127, then back down, 10-63 colors become Red & Green.
If DMX is raised to 128-191, then back down, 64-127 colors become Blue & Green.
If DMX is raised to 192-239, then back down, 128-191 colors become Cool White/Warm White.
If DMX is raised to 240-254, then back down, 192-239 colors become Cool White/Warm White.
CHANNEL NO.
VALUE
FUNCTION
1
0-255
Red Level
2
0-255
Green Level
3
0-255
Blue Level
4
0-255
White Level
5
0-255
Amber Level
CHANNEL
FUNCTION
VALUE
DESCRIPTION
1
Master Dimmer
0-255
Master Dimmer
2
Strobe Control
0-255
Strobe slow to fast
3
Dimming Red
0-255
Linear 0-100%, from dark to bright
4
Dimming Green
0-255
Linear 0-100%, from dark to bright
5
Dimming Blue
0-255
Linear 0-100%, from dark to bright
6
Dimming White
0-255
Linear 0-100%, from dark to bright
7
Dimming Amber
0-255
Linear 0-100%, from dark to bright
0-9
Applicable to CH2-CH7
10-34
Red Fade In
35-64
Red 100% intensity, Green Fade In
65-94
Green 100%, Red Fade Out
8
Color Macro
95-97
Green
98-127
Green 100%, Blue Fade In
128-157
Blue 100%, Green Fade Out
158-160
Blue
161-190
Blue 100%, Red Fade In
191-225
Red & Blue 100%, Green Fade In
226-255
Red, Green, Blue & White 100%, Amber
Fade In
Color Effect
0-9
CH2-CH7 functions
Raising DMX
10-63
Red & Blue (slow to fast)
Value
64-127
Red & Blue (slow to fast)
128-191
Red & Green (slow to fast)
9
192-239
Blue & Green (slow to fast)
Color Effect
239-192
Blue & Green (fast to slow)
Lowering DMX
191-128
Cool White/Warm White (fast to slow)
Value*
127-064
Blue & Green (fast to slow)
63-10
Red & Green (fast to slow)
9-0
CH2-CH7 functions
Sound Control
240-255
Sound Control Activate

This product is warranted for a period of TWO YEARS from the date of purchase against defects
in materials and workmanship.
This warranty is subject to the following restrictions and conditions:
A) If service is required, you may be asked to provide proof of purchase from an authorized
Lightronics dealer.
B) This warranty is valid only for the original purchaser of the unit.
C) This warranty does not apply to damage resulting from abuse, misuse, accidents, shipping,
and repairs or modifications by anyone other than an authorized Lightronics service
representative.
D) This warranty is void if the serial number is removed, altered or defaced.
E) This warranty does not cover loss or damage, direct or indirect arising from the use or
inability to use this product.
F) Lightronics reserves the right to make any changes, modifications, or updates as deemed
appropriate by Lightronics to products returned for service. Such changes may be made
without prior notification to the user and without incurring any responsibility or liability for
modifications or changes to equipment previously supplied. Lightronics is not responsible for
supplying new equipment in accordance with any earlier specifications.
G) This warranty is the only warranty either expressed, implied, or statutory, upon which the
equipment is purchased. No representatives, dealers or any of their agents are authorized to
make any warranties, guarantees, or representations other than expressly stated herein.
H) This warranty does not cover the cost of shipping products to or from Lightronics for
service.
I) Lightronics Inc. reserves the right to make changes as deemed necessary to this warranty
without prior notification.
Lightronics Inc. 509 Central Drive Virginia Beach, VA 23454 20100211
WARRANTY