Limora 218416 User manual

531460 LC20122019
Ultrasonic cleaner
Important information
1. Please read these instructions carefully before using the
unit.
2. Keep the unit out of reach from children or inrm persons.
Do not let them use it without supervision.
3. Do not immerse in water or other liquids or use near wash
basins. Do not use it with wet hands.
4. Always ensure that lhe unit has completely cooled down
before storing
5. The unit is only used indoor
6. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or a similarly qualied per-
son in order to avoid a hazard.
7. This product is factory tted with a plug. If thesupplied
plug does not t your household sockets, the plug should
be removed and use an appropriate one tted. The re-
moved plug should be destroyed safely. The flexible cord
insulation should be stripped back appropriately and
connect a suitable alternative plug tted correctly.
8. An appliance dropped or damaged should not be used
until examined by a service engineer.
9. Do not permit the mains lead to come in contact with hot
objects. Please ask a service engineer to replace a worn or
damaged main lead immediately with an approved lead of
the same size and type.
10. Do not attempt to repair or service the unit unless you
are qualied to do so and have the relevant calibration,
performance test, and service information.
11. Cleaning
Make sure that the unit has been turned o, and then
unplug the unit from the socket and allow to cool com-
pletely before cleaning. Wipe with a damp cloth and dry
immediately with a sott dry cloth. Do not use abrasive
cleaners on the unit. Never immerse appliance in water
or other liquid.
Theory
Ultrasonic generator produces an electric signal with a
certain power and a certain frequency. This signal is sent to
a high-eciency energy converter which can convert electric
energy into mechanical energy and produce strong ultraso-
nic vibration.
The ultrasonic vibration can make the liquid in the container
produce large amounts of tiny bubble, which is named cavi-
tation. Bubbles appear and then disappear, it causes strong
wallop which reduces the adhesion between the dirt and the
object being cleaned and removes the dirt from the object
aer a while. Finally you can wash this object with clean
water for desired cleanliness. The property and temperature
of the washing solution aects the cleaning eect.
Function
1. Be able to clean all kinds of electric components and
circuit board.
2. Be able to clean all kinds of golden or silvern objects,
glasses, etc.
3. Be able to clean all kinds of small industrial parts.
Operation introduction
1. Add cleaning solution of not less than one third of the
volume of container into the container. Note: The surface
of the cleaning solution must not exceed the „MAX“ mark
on the container.
2. Plug the power cable to the socket.
3. Press the power button. This unit begins to work and its
power consumption is 35 watts. 5 minutes later, this unit
auto powers o (you can manually turn o this unit ahead
of time by pressing the power button again).
4. When you nish cleaning, switch this unit o, remove the
the dirty solution from the container, then clean and dry
the container.

531460 LC20122019
Note
1. To avoid damage to this unit, don‘t switch this unit on
before you add cleaning solution into the container.
2. Never use unstable solution, such as tetrachloride carbon
which will produce poisonous gas.
3. If you don‘t use this unit for a long time, pull out the plug.
4.This appliance is not for medical use.
Feature
1. All the surface covered by solution can be cleaned becau-
se the ultrasonic eect exists throughout the solution.
Its advantage is being able to clean the object with com-
plicated surface and many apertures.
2. No damage to the object to be cleaned. Traditional
cleaning methods including manual cleaning method and
chemical cleaning method may cause mechanical damage
or chemical corrosion to the object. On the contrary, ultra-
sonic cleaning doesn‘t do any harm to the cleaned object.
3. Be able to clean all kinds of solid objects. Depending on
the character of the object, you can use dierent cleaning
solution. Improved by ultrasonic, the penetration and
dissolution eects of the cleaning solution function very
well. All the cleaned objects have new images and make
you feel fresh.
Specication
1. Power supply: 220-240Vac, 50Hz
2. Power: 35W
3. Frequency: 42KHz± 1KHz
4. Size: 184mm(L) X 128mm(W) X 113mm(H)
5. Weight: about 900g