Lincat Seal HB2 Operating instructions

IS280 ECN2841
User and Installation Instructions
Seal Heated Display Bars
HB2, HB3, HB4, LD2, LD3, LD4

IS280 ECN2841 Page 2
Dear Customer,
Thank you for purchasing this Lincat product.
This is just one of over 450 different items of catering equipment available which is
constantly being extended and improved. Details are available from your local
distributor or direct from us.
Used for the purposes for which it is intended, and with careful maintenance as
outlined in this User Guide, your Lincat product will give years of trouble free use.
IMPORTANT INFORMATION
Please read all of the safety and operating instructions carefully
before using this product. Please pay particular attention to all
sections of this User Guide that carry warning symbols and notices.
WARNING!
This is a Warning symbol. This symbol is used throughout the
User Guide whenever there is a risk of personal injury. Ensure
that these warnings are read and understood at all times.
CAUTION!
This is a Caution symbol. This symbol is used throughout the User
Guide whenever there is a risk damaging your Lincat product. Ensure
that these warnings are read and understood at all times. 
NOTE:
This is a Note symbol. This symbol is used throughout the User Guide to
provide additional information, hints and tips.
NOTE

IS280 ECN2841 Page 3
CONTENTS
Contents Page
Safety instructions………………………………………………………4
Product specification………………………………………………….. 5
Features………………………………………………………………….. 5
Technical specification…………………………………………………5
Pack contents…………………………………………………….………5
Spare parts list………………………………………………………….. 5
Installation……………………………………………………………….. 6
Connecting to the electricity supply……………………………. 6
Operating instructions………………………………………………….7
Cleaning and maintenance…………………………………………….7
Service information……………………………………………………..8
Conditions of guarantee…..…………………………………….……..8
USE OF THE HEATED DISPLAY UNITS
The Heated Display Units are intended to be used on counter tops to display
pre-heated food products.

IS280 ECN2841 Page 4
SAFETY INSTRUCTIONS
WARNING!
Basic safety precautions, including the following, should be
followed to reduce the risk of personal injury. Make sure you
have read all of these instructions before switching on the unit.
Keep this User Guide in a safe place for future reference for you and your
staff.
Do not clean the unit with a water jet.
REMOVAL OF PACKAGING
In the interest of hygiene, you should clean the product after unpacking and
ensure all plastic coatings are removed before use.
Take care when moving this unit.
GENERAL
Do not try to modify this product.
Ensure that the electrical supply cable is not damaged.
If the supply cable is damaged, it should be replaced by Lincat Ltd or suitably
qualified persons, in order to avoid a hazard.
EQUIPOTENTIALITY
This equipment is provided with an equipotential bonding terminal to
allow earth cross-bonding with other equipment.

IS280 ECN2841 Page 5
PRODUCT SPECIFICATION
PACK CONTENTS
FEATURES
SPARE PARTS LIST
TECHNICAL SPECIFICATION
Heated Display – HB2, HB3, HB4
Heated Display & Light Gantry – LD2, LD3, LD4
Stainless steel body
Aluminium hob surface
Thermostatic control
Infra-red heat lamp (LD model only)
230V, 50Hz, single phase
Model LD2 LD3 LD4 HB2
HB3 HB4
GN container
capacity 1/1 GN 2 3 4 2 3 4
Power rating kW 1.5 2.4 2.75 1.0 1.4 1.75
Width mm 790 1130 1470 754 1094 1434
Depth mm 538 538 538 531 531 531
Height mm 562 562 562 115 115 115
Weight (net) kg 18 24 30 11 15 19
Accessory LDBM2 LDBM3 LDBM4 HBBM2 HBBM3 HBBM4
GN container
capacity 2/3 GN 2 3 4 2 3 4
Overall Height mm 180 180 180
HB (Heated Base) or LD (Heated Display with integral light gantry and
sneeze screen) fitted with cable and 13 Amp plug.
Sneeze screen fittings: M5 screws, washers, self-lock nuts, nylon sleeves.
HBBM support frame with GN containers and lids (if ordered with HB units).
LDBM support frame with GN containers and lids (if ordered with LD units).
User Guide and Guarantee Card
Component LD2 / HB2 LD3 / HB3 LD4 / HB4
Element EL136 EL135 EL134
Thermostat TH69 TH69 TH69
Infra-red lamp LA210 LA210 LA210
Control knob KN203 KN203 KN203
On/Off switch SW67 SW67 SW67
Lamp switch SW68 SW68 SW68
Foot FE10 FE10 FE10
Glass panel GL492 GL493 GL494

IS280 ECN2841 Page 6
INSTALLATION
Ensure the unit is installed on a sound, level work surface, which is heat
resistant e.g. stainless steel or Formica ®. The unit’s external surfaces
and base will become hot. You should inform your personnel and
customers accordingly.
Do not remove the feet otherwise the unit will overheat.
For safety regulations, the plug must always be accessible.
Fixing diagram for LD sneeze
screen, using supplied fasteners.
CONNECTING TO THE ELECTRICITY SUPPLY
Ensure that the voltage of your electricity supply corresponds to the serial
plate details. The product is supplied with a 13 Amp plug. To replace the
plug, follow these instructions:
•green and yellow wire to 'E'or (Earth)
•blue wire to 'N'(Neutral)
•brown wire to 'L'(Live)
THIS APPLIANCE MUST BE EARTHED.
NOTE

IS280 ECN2841 Page 7
OPERATING INSTRUCTIONS
CLEANING AND
MAINTENANCE
Connect the unit to the electricity supply.
Ensure that the cable (4) is in good
condition.
Switch the unit on (2) and turn the
temperature controller (1) to the desired
setting. Wait for about 20 minutes for the
unit to heat up. Place the dishes/
Gastronorm containers with hot food
onto the aluminium hob surface.
Switch on the Infra-red lamp (3).
CLEANING
Disconnect the product from the electricity supply and ensure that it
is cool to touch, before starting to clean. Use a mild detergent in hot
water and a soft cloth. Do not use abrasive creams or scourers. Use
a suitable polish on the exterior metal surfaces by spraying onto the cloth (not
directly onto the steel).
MAINTENANCE
Regular cleaning of the unit is recommended. No regular
maintenance is required, but it may be necessary to replace a light
tube.
Before operation, replace damaged switches, feet, or control knobs.
The Infra-red lamps on LD units are user replaceable.
Disconnect the unit from the electricity supply and ensure the unit is
cool to touch.
The lamp is a “bayonet” type fit. To remove, push the lamp carefully to one side
into the end connector (against light spring resistance) allowing the other end to
detach from its connector. Dispose of the old lamp safely. Fitting the new lamp is
the reverse of the above sequence.
NOTE

1- Temperature Controller
2- On/Off Switch
3- Infra-red Lamp Switch
4- Cable

IS280 ECN2841 Page 8
SERVICE INFORMATION
GUARANTEE
For help regarding the installation, maintenance and use of your Lincat
equipment, please contact our Service Department:
01522 875520
All service work, other than routine cleaning should be carried out by one of our
authorised service agents. We cannot accept responsibility for work carried out
by other persons.
To ensure your call is service enquiry is handled as efficiently as possible, you
need to have the following details available:
Brief details of problem
Product code, type number and serial number of unit (both on serial plate)
Code number of spare part (see spare parts list P. 5), if known
Lincat reserve the right to carry out any work under warranty during normal
working hours, i.e. Monday to Friday, 8.30 a.m. – 5.00 p.m.
This unit carries a comprehensive UK twelve-month warranty. The
guarantee is in addition to, and does not diminish your statutory or legal
rights.
The guarantee does not cover: -
• Accidental damage, misuse (or use not in accordance with the instructions in
this User Guide), or consumable items
• Damage due to incorrect installation, modification or unauthorised service
work
• The manufacturer disclaims any liability for incidental, or consequential
damages