Lincoln electric Omnishield Instruction Manual

these steps

to help increase the longevity and

usefulness of your OMNIShield®

face shield.

• Lightly blow o any loose dirt or debrisfrom

the lens

• Use a soft microber cloth or eyewear-

approved tissue to clean the lens

• Rinse your lenses with cool water and wipe

clean with lens-safe tissue

• Only use lens cleaning products to clean lenses

by spraying eyewear-specic cleaning solution

directly onto the lens and wipe clean with

lenssafe tissue

• Store face shield in a secure spot like a locker,

or shelving, but never on a table or around

your work area.

OMNISHIELD® FACE SHIELD

General Cleaning Guidelines

General Guidelines

WARNING

Maintenance And Storage

• Read and follow all steps set forth in the

OMNIShield® Operator’s Manual.

• Inspect face shield prior to each use. If there is

any sign of damage, such as pit marks, cracks,

scratches, or distortion, impact resistance is

severely reduced, OMNIShield® lens should be

replaced immediately.

• Never use solvents or abrasive cleaning

solutions to clean the OMNIShield®.

• Wash with mild detergent and warm water.

Rinse clean and remove excess water by patting

with soft tissue or cloth. DO NOT use ammonia,

alkaline cleaners, solvents, or abrasive cleaning

compounds, which may reduce visibility, impact

resistance and eectiveness of coatings.

• Cleaning is recommended after each use.

Important Notice:

• Follow your facility’s protocols for proper

disposal of cleaning equipment and solutions

OMNIShield® Lens Cleaning

Improper cleaning, poor handling and storage of

the OMNIShield® can result in reduced visibility,

impact resistance and eectiveness of coatings.

1. To disassemble the lens, press the enclosed

button located in the center of the inside

headpiece. Rotate the lens so the locking pins

on each side of the headpiece align with the lens

notch in each corner. Then push each side of the

lens to detach from the headpiece.

2. Use a warm, mild detergent cleaning solution.

3. Wipe with a soft cloth until clean.

a. DO NOT use detergents that contain lanolin or

other oils, organic or chlorinated solvents or

abrasive cleaning agents. Rinsing OMNIShield®

Lens.

1. Rinse the OMNIShield® lens by wiping with a

clean soft cloth, lightly dampened with clean

warm water, and thoroughly dry before use or

storage.

Important Notice:

• Ensure all components are dry prior to reuse or

storage.

• The cleaned OMNIShield® lens should be

carefully inspected per the OMNIShield®

Operator’s Manual.

OMNIShield® Headpiece Cleaning

Improper cleaning, poor handling and storage

of the OMNIShield® all result in reduced impact

resistance.

1. Disassemble the headpiece from the lens.

2. Use a warm, mild detergent cleaning solution.

3. Wipe with a soft cloth until clean.

a. DO NOT use detergents that contain lanolin or

other oils, organic or chlorinated solvents or

abrasive cleaning agents. Rinsing OMNIShield®

Headpiece.

1. Rinse the OMNIShield® lens by wiping with a

clean soft cloth, lightly dampened with clean

warm water, and thoroughly dry before use or

storage.

Disinfecting Safety Glasses & Goggles Lens.

1. Disinfect the Safety Glasses & Goggles lens by

wiping with a suitable disinfecting material

recommended by the EPA after drying and

before use: https://www.epa.gov/pesticide-

registration/selected-eparegistered-

disinfectants.

Important Notice:

• Ensure all components are dry prior to reuse or

storage.

• The cleaned OMNIShield® headpiece should

be carefully inspected per the OMNIShield®

Operator’s Manual.

The Lincoln Electric Company

22801 St. Clair Avenue

Cleveland, OH 44117-1199 U.S.A.

www.lincolnelectric.com/helmets

OMNIShield® Face Shield

General Cleaning Guidelines

Issue Date 07/2020

User’s Guide

KPXXXX-1

Maintenance And Storage

• Read and follow all steps set forth in the OMNIShield® Operator’s Manual.

• Inspect face shield prior to each use. If there is any sign of damage, such as pit marks,

cracks, scratches, or distortion, impact resistance is severely reduced, OMNIShield®

lens should be replaced immediately.

• Never use solvents or abrasive cleaning solutions to clean the OMNIShield®.

• Wash with mild detergent and warm water. Rinse clean and remove excess water by

patting with soft tissue or cloth. DO NOT use ammonia, alkaline cleaners, solvents, or

abrasive cleaning compounds, which may reduce visibility, impact resistance and

eectiveness of coatings.

• Cleaning is recommended after each use.

IMPORTANT NOTICE:

• Follow your facility’s protocols for proper disposal of cleaning equipment and solutions.

OMNIShield® Lens Cleaning

Improper cleaning, poor handling and storage of the OMNIShield® can result in

reduced visibility, impact resistance and eectiveness of coatings.

1. To disassemble the lens, press the enclosed button located in the center of the inside

headpiece. Rotate the lens so the locking pins on each side of the headpiece align with the

lens notch in each corner. Then push each side of the lens to detach from the headpiece.

2. Use a warm, mild detergent cleaning solution.

3. Wipe with a soft cloth until clean.

a. Do not use detergents that contain lanolin or other oils, organic or chlorinated solvents or

abrasive cleaning agents.

Rinsing OMNIShield® Lens.

1. Rinse the OMNIShield® lens by wiping with a clean soft cloth, lightly dampened with clean

warm water, and thoroughly dry before use or storage.

IMPORTANT NOTICE:

• Ensure all components are dry prior to reuse or storage.

• The cleaned OMNIShield® lens should be carefully inspected per the OMNIShield® Operator’s

Manual.

OMNIShield® Headpiece Cleaning

Improper cleaning, poor handling and storage of the OMNIShield® all result in reduced

impact resistance.

1. Disassemble the headpiece from the lens.

2. Use a warm, mild detergent cleaning solution.

3. Wipe with a soft cloth until clean.

a. Do not use detergents that contain lanolin or other oils, organic or chlorinated solvents or

abrasive cleaning agents.

Rinsing OMNIShield® Headpiece.

1. Rinse the OMNIShield® lens by wiping with a clean soft cloth, lightly dampened with clean

warm water, and thoroughly dry before use or storage.

IMPORTANT NOTICE:

• Ensure all components are dry prior to reuse or storage.

• The cleaned OMNIShield® headpiece should be carefully inspected per the OMNIShield®

Operator’s Manual.

WARNING

General Guidelines

Follow these steps to help increase the longevity

and usefulness of your OMNIShield® face shield.

• Lightly blow o any loose dirt or debris

from the lens

• Use a soft microfiber cloth or eyewear-approved

tissue to clean the lens

• Rinse your lenses with cool water and wipe

clean with lens-safe tissue

• Only use lens cleaning products to clean lenses

by spraying eyewear-specific cleaning solution

directly onto the lens and wipe clean with lens-

safe tissue

• Store face shield in a secure spot like a locker,

or shelving, but never on a table or around your

work area.

CUSTOMER ASSISTANCE POLICY

The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet

the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for information or advice about their use of

our products. Our employees respond to inquiries to the best of their ability based on information provided to them by the customers and the knowledge

they may have concerning the application. Our employees, however, are not in a position to verify the information provided or to evaluate the engineering

requirements for the particular weldment. Accordingly, Lincoln Electric does not warrant or guarantee or assume any liability with respect to such information

or advice. Moreover, the provision of such information or advice does not create, expand, or alter any warranty on our products. Any express or implied

warranty that might arise from the information or advice, including any implied warranty of merchantability or any warranty of tness for any customers’

particular purpose is specically disclaimed.

Lincoln Electric is a responsive manufacturer, but the selection and use of specic products sold by Lincoln Electric is solely within the control of, and remains

the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric aect the results obtained in applying these types of

fabrication methods and service requirements.

Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any

updated information.

THE LINCOLN ELECTRIC COMPANY