Lincoln Electric POWER WAVE 405 IM746 User manual

POWER WAVE 405
OPERATOR’S MANUAL
For use with machines Code 10896
IM746
August, 2004
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation ... and thought-
ful operation on your part. DO
NOT INSTALL, OPERATE OR
REPAIR THIS EQUIPMENT
WITHOUT READING THIS
MANUAL AND THE SAFETY
PRECAUTIONS CONTAINED
THROUGHOUT. And, most
importantly, think before you act
and be careful.
WARNING
WARNING AVISO DE
PRECAUCION
ATTENTION
!!
!!
Loremipsumdolor sit amet consectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, ed diam non
elit, eddiamnon
umm
umm
ynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreet doloremagna aliquamer
laoreetdoloremagnaaliquamer
at
at
Loremipsum dolor sit ametconsectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, ed diamnon
elit, eddiamnon
umm
umm
ynibheuismodtincidunt ut
ynibheuismodtinciduntut
laoreetdolore magnaaliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsum dolor sit amet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,ed diam non
elit,eddiamnon
umm
umm
ynibheuismodtincidunt ut
ynibheuismodtinciduntut
laoreet doloremagna aliquamer
laoreetdoloremagnaaliquamer
at
at
Loremipsum dolor sit amet consectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,ed diamnon
elit,eddiamnon
umm
umm
ynibh euismodtincidunt ut
ynibheuismodtinciduntut
laoreetdolore magnaaliquamer
laoreetdoloremagnaaliquamer
at
at
Loremipsumdolorsit amet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, eddiam non
elit, eddiamnon
umm
umm
ynibh euismodtincidunt ut
ynibheuismodtinciduntut
laoreetdolore magna aliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsumdolor sit ametconsectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, eddiamnon
elit,eddiamnon
umm
umm
ynibheuismodtincidunt ut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsum dolorsitamet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon
elit,eddiamnon
umm
umm
ynibh euismod tincidunt ut
ynibheuismodtinciduntut
laoreet doloremagna aliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiam non
elit,eddiamnon
umm
umm
ynibheuismodtincidunt ut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquamer
at
at
Loremipsum dolor sit amet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiam non
elit,eddiamnon
umm
umm
ynibheuismod tincidunt ut
ynibheuismodtinciduntut
laoreet dolore magna aliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsumdolor sit ametconsectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, eddiam non
elit, eddiamnon
umm
umm
ynibheuismod tincidunt ut
ynibheuismodtinciduntut
laoreet doloremagna aliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsum dolor sit amet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, ed diamnon
elit,eddiamnon
umm
umm
ynibheuismod tincidunt ut
ynibheuismodtinciduntut
laoreet dolore magna aliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsum dolor sitametconsectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon
elit,eddiamnon
umm
umm
ynibheuismod tincidunt ut
ynibheuismodtinciduntut
laoreet doloremagnaaliquamer
laoreetdoloremagnaaliquamer
at
at
Loremipsumdolor sitamet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, eddiam non
elit, eddiamnon
umm
umm
ynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreet doloremagna aliquam er
laoreetdoloremagnaaliquamer
at
at
Lorem ipsum dolor sit amet consectetuer adipiscing
Loremipsumdolorsit ametconsectetueradipiscing
elit, ed diam non
elit, ed diam non
umm
umm
y nibh euismod tincidunt ut
y nibh euismodtinciduntut
laoreet dolore magna aliquam er
laoreet doloremagnaaliquamer
at
at
Lorem ipsum dolor sit amet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit, ed diam non
elit, ed diam non
umm
umm
y nibh euismod tincidunt ut
y nibh euismodtinciduntut
laoreet dolore magna aliquam er
laoreetdoloremagnaaliquamer
at
at
Lorem ipsum dolor sit amet consectetuer adipiscing
Loremipsumdolorsit amet consectetueradipiscing
elit, ed diam non
elit, ed diam non
umm
umm
y nibh euismod tincidunt ut
y nibh euismodtincidunt ut
laoreet dolore magna aliquam er
laoreet doloremagnaaliquamer
at
at
Lorem ipsum dolor sit amet consectetuer adipiscing
Loremipsumdolorsitametconsectetuer adipiscing
elit, ed diam non
elit, ed diam non
umm
umm
y nibh euismod tincidunt ut
y nibh euismodtinciduntut
laoreet dolore magna aliquam er
laoreet doloremagnaaliquamer
at
at
Loremipsum dolor sit amet consectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,ed diamnon
elit,eddiamnon
umm
umm
ynibheuismod tinciduntut
ynibheuismodtinciduntut
laoreet dolore magnaaliquam er
laoreetdoloremagnaaliquamer
at
at
Loremipsumdolor sit amet consectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,ed diamnon
elit,eddiamnon
umm
umm
ynibheuismod tincidunt ut
ynibheuismodtinciduntut
laoreet doloremagnaaliquam er
laoreetdoloremagnaaliquamer
at
at
WARNING
REMOTE POWER
OFF
ON
P O W E R W A V E 4 0 5
• Sales and Service through Subsidiaries and Distributors Worldwide •
Cleveland, Ohio 44117-1199 U.S.A. TEL: [phone] FAX: [phone] WEB SITE: www.lincolnelectric.com
• World's Leader in Welding and Cutting Products •
Copyright © 2004 Lincoln Global Inc.

FOR ENGINE
powered equipment.
1.a. Turn the engine off before troubleshooting and maintenance
work unless the maintenance work requires it to be running.
____________________________________________________
1.b. Operate engines in open, well-ventilated
areas or vent the engine exhaust fumes
outdoors.
____________________________________________________
1.c. Do not add the fuel near an open flame
welding arc or when the engine is running.
Stop the engine and allow it to cool before
refueling to prevent spilled fuel from vaporiz-
ing on contact with hot engine parts and
igniting. Do not spill fuel when filling tank. If
fuel is spilled, wipe it up and do not start
engine until fumes have been eliminated.
____________________________________________________
1.d. Keep all equipment safety guards, covers and devices in
position and in good repair.Keep hands, hair, clothing and
tools away from V-belts, gears, fans and all other moving
parts when starting, operating or repairing equipment.
____________________________________________________
1.e. In some cases it may be necessary to remove safety
guards to perform required maintenance. Remove
guards only when necessary and replace them when the
maintenance requiring their removal is complete.
Always use the greatest care when working near moving
parts.
___________________________________________________
1.f. Do not put your hands near the engine fan.
Do not attempt to override the governor or
idler by pushing on the throttle control rods
while the engine is running.
___________________________________________________
1.g. To prevent accidentally starting gasoline engines while
turning the engine or welding generator during maintenance
work, disconnect the spark plug wires, distributor cap or
magneto wire as appropriate.
i
SAFETY
i
ARC WELDING CAN BE HAZARDOUS. PROTECT YOURSELF AND OTHERS FROM POSSIBLE SERIOUS INJURY OR DEATH.
KEEP CHILDREN AWAY. PACEMAKER WEARERS SHOULD CONSULT WITH THEIR DOCTOR BEFORE OPERATING.
Read and understand the following safety highlights. For additional safety information, it is strongly recommended that you
purchase a copy of “Safety in Welding & Cutting - ANSI Standard Z49.1” from the American Welding Society, P.O. Box
351040, Miami, Florida 33135 or CSA Standard W117.2-1974. A Free copy of “Arc Welding Safety” booklet E205 is available
from the Lincoln Electric Company, 22801 St. Clair Avenue, Cleveland, Ohio 44117-1199.
BE SURE THAT ALL INSTALLATION, OPERATION, MAINTENANCE AND REPAIR PROCEDURES ARE
PERFORMED ONLY BY QUALIFIED INDIVIDUALS.
WARNING
Mar ‘95
ELECTRIC AND
MAGNETIC FIELDS
may be dangerous
2.a. Electric current flowing through any conductor causes
localized Electric and Magnetic Fields (EMF). Welding
current creates EMF fields around welding cables and
welding machines
2.b. EMF fields may interfere with some pacemakers, and
welders having a pacemaker should consult their physician
before welding.
2.c. Exposure to EMF fields in welding may have other health
effects which are now not known.
2.d. All welders should use the following procedures in order to
minimize exposure to EMF fields from the welding circuit:
2.d.1.
Route the electrode and work cables together - Secure
them with tape when possible.
2.d.2. Never coil the electrode lead around your body.
2.d.3. Do not place your body between the electrode and
work cables. If the electrode cable is on your right
side, the work cable should also be on your right side.
2.d.4. Connect the work cable to the workpiece as close as
possible to the area being welded.
2.d.5. Do not work next to welding power source.
1.h. To avoid scalding, do not remove the
radiator pressure cap when the engine is
hot.
CALIFORNIA PROPOSITION 65 WARNINGS
Diesel engine exhaust and some of its constituents
are known to the State of California to cause can-
cer, birth defects, and other reproductive harm.
The engine exhaust from this product contains
chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
The Above For Diesel Engines The Above For Gasoline Engines
POWER WAVE 405

ii
SAFETY
ii
ARC RAYS can burn.
4.a. Use a shield with the proper filter and cover
plates to protect your eyes from sparks and
the rays of the arc when welding or observing
open arc welding. Headshield and filter lens
should conform to ANSI Z87. I standards.
4.b. Use suitable clothing made from durable flame-resistant
material to protect your skin and that of your helpers from
the arc rays.
4.c. Protect other nearby personnel with suitable, non-flammable
screening and/or warn them not to watch the arc nor expose
themselves to the arc rays or to hot spatter or metal.
ELECTRIC SHOCK can
kill.
3.a. The electrode and work (or ground) circuits
are electrically “hot” when the welder is on.
Do not touch these “hot” parts with your bare
skin or wet clothing. Wear dry, hole-free
gloves to insulate hands.
3.b. Insulate yourself from work and ground using dry insulation.
Make certain the insulation is large enough to cover your full
area of physical contact with work and ground.
In addition to the normal safety precautions, if welding
must be performed under electrically hazardous
conditions (in damp locations or while wearing wet
clothing; on metal structures such as floors, gratings or
scaffolds; when in cramped positions such as sitting,
kneeling or lying, if there is a high risk of unavoidable or
accidental contact with the workpiece or ground) use
the following equipment:
• Semiautomatic DC Constant Voltage (Wire) Welder.
• DC Manual (Stick) Welder.
• AC Welder with Reduced Voltage Control.
3.c. In semiautomatic or automatic wire welding, the electrode,
electrode reel, welding head, nozzle or semiautomatic
welding gun are also electrically “hot”.
3.d. Always be sure the work cable makes a good electrical
connection with the metal being welded. The connection
should be as close as possible to the area being welded.
3.e. Ground the work or metal to be welded to a good electrical
(earth) ground.
3.f.
Maintain the electrode holder, work clamp, welding cable and
welding machine in good, safe operating condition. Replace
damaged insulation.
3.g. Never dip the electrode in water for cooling.
3.h. Never simultaneously touch electrically “hot” parts of
electrode holders connected to two welders because voltage
between the two can be the total of the open circuit voltage
of both welders.
3.i. When working above floor level, use a safety belt to protect
yourself from a fall should you get a shock.
3.j. Also see Items 6.c. and 8.
FUMES AND GASES
can be dangerous.
5.a. Welding may produce fumes and gases
hazardous to health. Avoid breathing these
fumes and gases.When welding, keep
your head out of the fume. Use enough
ventilation and/or exhaust at the arc to keep
fumes and gases away from the breathing zone. When
welding with electrodes which require special
ventilation such as stainless or hard facing (see
instructions on container or MSDS) or on lead or
cadmium plated steel and other metals or coatings
which produce highly toxic fumes, keep exposure as
low as possible and below Threshold Limit Values (TLV)
using local exhaust or mechanical ventilation. In
confined spaces or in some circumstances, outdoors, a
respirator may be required. Additional precautions are
also required when welding on galvanized steel.
5.b.
Do not weld in locations near chlorinated hydrocarbon vapors
coming from degreasing, cleaning or spraying operations.
The heat and rays of the arc can react with solvent vapors to
form phosgene, a highly toxic gas, and other irritating prod-
ucts.
5.c. Shielding gases used for arc welding can displace air and
cause injury or death. Always use enough ventilation,
especially in confined areas, to insure breathing air is safe.
5.d. Read and understand the manufacturer’s instructions for this
equipment and the consumables to be used, including the
material safety data sheet (MSDS) and follow your
employer’s safety practices. MSDS forms are available from
your welding distributor or from the manufacturer.
5.e. Also see item 1.b.
Mar ‘95
POWER WAVE 405

FOR ELECTRICALLY
powered equipment.
8.a. Turn off input power using the disconnect
switch at the fuse box before working on
the equipment.
8.b. Install equipment in accordance with the U.S. National
Electrical Code, all local codes and the manufacturer’s
recommendations.
8.c. Ground the equipment in accordance with the U.S. National
Electrical Code and the manufacturer’s recommendations.
CYLINDER may explode
if damaged.
7.a. Use only compressed gas cylinders
containing the correct shielding gas for the
process used and properly operating
regulators designed for the gas and
pressure used. All hoses, fittings, etc. should be suitable for
the application and maintained in good condition.
7.b. Always keep cylinders in an upright position securely
chained to an undercarriage or fixed support.
7.c. Cylinders should be located:
• Away from areas where they may be struck or subjected to
physical damage.
• A safe distance from arc welding or cutting operations and
any other source of heat, sparks, or flame.
7.d. Never allow the electrode, electrode holder or any other
electrically “hot” parts to touch a cylinder.
7.e. Keep your head and face away from the cylinder valve outlet
when opening the cylinder valve.
7.f. Valve protection caps should always be in place and hand
tight except when the cylinder is in use or connected for
use.
7.g. Read and follow the instructions on compressed gas
cylinders, associated equipment, and CGA publication P-l,
“Precautions for Safe Handling of Compressed Gases in
Cylinders,” available from the Compressed Gas Association
1235 Jefferson Davis Highway, Arlington, VA 22202.
iii
SAFETY
iii
Mar ‘95
WELDING SPARKS can
cause fire or explosion.
6.a. Remove fire hazards from the welding area.
If this is not possible, cover them to prevent
the welding sparks from starting a fire.
Remember that welding sparks and hot
materials from welding can easily go through small cracks
and openings to adjacent areas. Avoid welding near
hydraulic lines. Have a fire extinguisher readily available.
6.b. Where compressed gases are to be used at the job site,
special precautions should be used to prevent hazardous
situations. Refer to “Safety in Welding and Cutting” (ANSI
Standard Z49.1) and the operating information for the
equipment being used.
6.c. When not welding, make certain no part of the electrode
circuit is touching the work or ground. Accidental contact
can cause overheating and create a fire hazard.
6.d. Do not heat, cut or weld tanks, drums or containers until the
proper steps have been taken to insure that such procedures
will not cause flammable or toxic vapors from substances
inside. They can cause an explosion even though they have
been “cleaned”. For information, purchase “Recommended
Safe Practices for the
Preparation for Welding and Cutting of
Containers and Piping That Have Held Hazardous
Substances”, AWS F4.1 from the American Welding Society
(see address above).
6.e. Vent hollow castings or containers before heating, cutting or
welding. They may explode.
6.f.
Sparks and spatter are thrown from the welding arc. Wear oil
free protective garments such as leather gloves, heavy shirt,
cuffless trousers, high shoes and a cap over your hair. Wear
ear plugs when welding out of position or in confined places.
Always wear safety glasses with side shields when in a
welding area.
6.g. Connect the work cable to the work as close to the welding
area as practical. Work cables connected to the building
framework or other locations away from the welding area
increase the possibility of the welding current passing
through lifting chains, crane cables or other alternate cir-
cuits. This can create fire hazards or overheat lifting chains
or cables until they fail.
6.h. Also see item 1.c.
POWER WAVE 405

iv
SAFETY
iv
PRÉCAUTIONS DE SÛRETÉ
Pour votre propre protection lire et observer toutes les instructions
et les précautions de sûreté specifiques qui parraissent dans ce
manuel aussi bien que les précautions de sûreté générales suiv-
antes:
Sûreté Pour Soudage A L’Arc
1. Protegez-vous contre la secousse électrique:
a. Les circuits à l’électrode et à la piéce sont sous tension
quand la machine à souder est en marche. Eviter toujours
tout contact entre les parties sous tension et la peau nue
ou les vétements mouillés. Porter des gants secs et sans
trous pour isoler les mains.
b. Faire trés attention de bien s’isoler de la masse quand on
soude dans des endroits humides, ou sur un plancher
metallique ou des grilles metalliques, principalement dans
les positions assis ou couché pour lesquelles une grande
partie du corps peut être en contact avec la masse.
c. Maintenir le porte-électrode, la pince de masse, le câble
de soudage et la machine à souder en bon et sûr état
defonctionnement.
d.Ne jamais plonger le porte-électrode dans l’eau pour le
refroidir.
e. Ne jamais toucher simultanément les parties sous tension
des porte-électrodes connectés à deux machines à souder
parce que la tension entre les deux pinces peut être le
total de la tension à vide des deux machines.
f. Si on utilise la machine à souder comme une source de
courant pour soudage semi-automatique, ces precautions
pour le porte-électrode s’applicuent aussi au pistolet de
soudage.
2. Dans le cas de travail au dessus du niveau du sol, se protéger
contre les chutes dans le cas ou on recoit un choc. Ne jamais
enrouler le câble-électrode autour de n’importe quelle partie
du corps.
3. Un coup d’arc peut être plus sévère qu’un coup de soliel,
donc:
a. Utiliser un bon masque avec un verre filtrant approprié
ainsi qu’un verre blanc afin de se protéger les yeux du ray-
onnement de l’arc et des projections quand on soude ou
quand on regarde l’arc.
b. Porter des vêtements convenables afin de protéger la
peau de soudeur et des aides contre le rayonnement de
l‘arc.
c. Protéger l’autre personnel travaillant à proximité au
soudage à l’aide d’écrans appropriés et non-inflammables.
4. Des gouttes de laitier en fusion sont émises de l’arc de
soudage. Se protéger avec des vêtements de protection libres
de l’huile, tels que les gants en cuir, chemise épaisse, pan-
talons sans revers, et chaussures montantes.
5. Toujours porter des lunettes de sécurité dans la zone de
soudage. Utiliser des lunettes avec écrans lateraux dans les
zones où l’on pique le laitier.
6. Eloigner les matériaux inflammables ou les recouvrir afin de
prévenir tout risque d’incendie dû aux étincelles.
7. Quand on ne soude pas, poser la pince à une endroit isolé de
la masse. Un court-circuit accidental peut provoquer un
échauffement et un risque d’incendie.
8. S’assurer que la masse est connectée le plus prés possible
de la zone de travail qu’il est pratique de le faire. Si on place
la masse sur la charpente de la construction ou d’autres
endroits éloignés de la zone de travail, on augmente le risque
de voir passer le courant de soudage par les chaines de lev-
age, câbles de grue, ou autres circuits. Cela peut provoquer
des risques d’incendie ou d’echauffement des chaines et des
câbles jusqu’à ce qu’ils se rompent.
9. Assurer une ventilation suffisante dans la zone de soudage.
Ceci est particuliérement important pour le soudage de tôles
galvanisées plombées, ou cadmiées ou tout autre métal qui
produit des fumeés toxiques.
10. Ne pas souder en présence de vapeurs de chlore provenant
d’opérations de dégraissage, nettoyage ou pistolage. La
chaleur ou les rayons de l’arc peuvent réagir avec les vapeurs
du solvant pour produire du phosgéne (gas fortement toxique)
ou autres produits irritants.
11. Pour obtenir de plus amples renseignements sur la sûreté,
voir le code “Code for safety in welding and cutting” CSA
Standard W 117.2-1974.
PRÉCAUTIONS DE SÛRETÉ POUR
LES MACHINES À SOUDER À
TRANSFORMATEUR ET À
REDRESSEUR
1. Relier à la terre le chassis du poste conformement au code de
l’électricité et aux recommendations du fabricant. Le dispositif
de montage ou la piece à souder doit être branché à une
bonne mise à la terre.
2. Autant que possible, I’installation et l’entretien du poste seront
effectués par un électricien qualifié.
3. Avant de faires des travaux à l’interieur de poste, la debranch-
er à l’interrupteur à la boite de fusibles.
4. Garder tous les couvercles et dispositifs de sûreté à leur
place.
Mar. ‘93
POWER WAVE 405

POWER WAVE 405
v
SAFETY
v
L10093
3-1-96H
Conformance
standard: EN 50 199 Electromagnetic Compatibility (EMC) Product Standard for Arc Welding Equipment. It
All electrical equipment generates small amounts of electromagnetic emission. Electrical emission may be
received by other equipment, electrical interference may result. Electrical emissions may affect many kinds of
telephone systems, computers, etc. Be aware that interference may result and extra precautions may be required
If electromagnetic disturbances are detected then it shall be the responsibility of the user of the welding equipment
to resolve the situation with the technical assistance of the manufacturer. In some cases this remedial action may
electromagnetic disturbances must be reduced to the point where they are no longer troublesome.
assess whether the changes will increase the risk of injury, e.g., by allowing parallel welding
surrounding area. The following shall be taken into account:
welding equipment;
b) radio and television transmitters and receivers;
d) safety critical equipment, e.g., guarding of industrial equipment;
e) the health of the people around, e.g., the use of pacemakers and hearing aids;
f) equipment used for calibration or measurement;
used in the environment is compatible. This may require additional protection measures;
ELECTROMAGNETIC COMPATIBILITY (EMC)
Products displaying the CE mark are in conformity with European Community Council Directive of 3 May
1989 on the approximation of the laws of the Member States relating to electromagnetic compatibility
(89/336/EEC). It was manufactured in conformity with a national standard that implements a harmonized
is for use with other Lincoln Electric equipment. It is designed for industrial and professional use.
Introduction
transmitted through power lines or radiated through space, similar to a radio transmitter. When emissions are
electrical equipment; other nearby welding equipment, radio andTV reception, numerical controlled machines,
when a welding power source is used in a domestic establishment.
Installation and Use
The user is responsible for installing and using the welding equipment according to the manufacturer s instructions.
be as simple as earthing (grounding) the welding circuit, see Note. In other cases it could involve constructing an
electromagnetic screen enclosing the power source and the work complete with associated input filters. In all cases
Note: The welding circuit may or may not be earthed for safety reasons according to national codes.
Changing the earthing arrangements should only be authorized by a person who is competent to
current return paths which may damage the earth circuits of other equipment.
Assessment of Area
Before installing welding equipment the user shall make an assessment of potential electromagnetic problems in the
a) other supply cables, control cables, signaling and telephone cables; above, below and adjacent to the
c) computer and other control equipment;
g) the immunity of other equipment in the environment. The user shall ensure that other equipment being
h) the time of day that welding or other activities are to be carried out.

POWER WAVE 405
vi
SAFETY
vi
L10093
3-1-96H
The size of the surrounding area to be considered will depend on the structure of the building and other activities
Methods of Reducing Emissions
Consideration should be given to shielding the supply cable of permanently installed welding equipment, in metallic
conduit or equivalent. Shielding should be electrically continuous throughout its length. The shielding should be
connected to the welding power source so that good electrical contact is maintained between the conduit and the
welding power source enclosure.
access and service doors and covers should be closed and properly fastened when the welding equipment is in
be adjusted and maintained according to the manufacturer s recommendations.
The welding cables should be kept as short as possible and should be positioned close together, running at or close
to the floor level.
Equipotential Bonding
touching these metallic components and the electrode at the same time. The operator should be insulated from all
Earthing of the Workpiece
of injury to users, or damage to other electrical equipment. Where necessary, the connection of the workpiece to
Screening and Shielding
Selective screening and shielding of other cables and equipment in the surrounding area may alleviate problems of
interference. Screening of the entire welding installation may be considered for special applications.
Portions of the preceding text are contained in EN50199: "Electromagnetic Compatibility (EMC) product standard for
arc welding equipment."
1
1
ELECTROMAGNETIC COMPATIBILITY (EMC)
that are taking place. The surrounding area may extend beyond the boundaries of the premises.
Mains Supply
Welding equipment should be connected to the mains supply according to the manufacturer s recommendations.
If interference occurs, it may be necessary to take additional precautions such as filtering of the mains supply.
Maintenance of the Welding Equipment
The welding equipment should be routinely maintained according to the manufacturer s recommendations. All
operation. The welding equipment should not be modified in any way except for those changes and adjustments
covered in the manufacturers instructions. In particular, the spark gaps of arc striking and stabilizing devices should
Welding Cables
Bonding of all metallic components in the welding installation and adjacent to it should be considered. However,
metallic components bonded to the work piece will increase the risk that the operator could receive a shock by
such bonded metallic components.
Where the workpiece is not bonded to earth for electrical safety, not connected to earth because of its size and
position, e.g., ships hull or building steelwork, a connection bonding the workpiece to earth may reduce emissions
in some, but not all instances. Care should be taken to prevent the earthing of the workpiece increasing the risk
earth should be made by a direct connection to the workpiece, but in some countries where direct connection is not
permitted, the bonding should be achieved by suitable capacitance, selected according to national regulations.

viivii
Thank You for selecting a QUALITY product by Lincoln Electric. We want you
to take pride in operating this Lincoln Electric Company product
••• as much pride as we have in bringing this product to you!
Read this Operators Manual completely before attempting to use this equipment. Save this manual and keep it
handy for quick reference. Pay particular attention to the safety instructions we have provided for your protection.
The level of seriousness to be applied to each is explained below:
WARNING
This statement appears where the information must be followed exactly to avoid serious personal injury or
loss of life.
This statement appears where the information must be followed to avoid minor personal injury or damage to
this equipment.
CAUTION
Please Examine Carton and Equipment For Damage Immediately
When this equipment is shipped, title passes to the purchaser upon receipt by the carrier. Consequently, Claims
for material damaged in shipment must be made by the purchaser against the transportation company at the
time the shipment is received.
Please record your equipment identification information below for future reference. This information can be
found on your machine nameplate.
Product _________________________________________________________________________________
Model Number ___________________________________________________________________________
Code Number or Date Code_________________________________________________________________
Serial Number____________________________________________________________________________
Date Purchased___________________________________________________________________________
Where Purchased_________________________________________________________________________
Whenever you request replacement parts or information on this equipment, always supply the information you
have recorded above. The code number is especially important when identifying the correct replacement parts.
On-Line Product Registration
- Register your machine with Lincoln Electric either via fax or over the Internet.
•For faxing: Complete the form on the back of the warranty statement included in the literature packet
accompanying this machine and fax the form per the instructions printed on it.
•For On-Line Registration: Go to our
WEB SITE at www.lincolnelectric.com. Choose “Quick Links”and then
“Product Registration”. Please complete the form and submit your registration.

viii
viii TABLE OF CONTENTS Page
Installation.......................................................................................................Section A
Technical Specifications - POWER WAVE 405 ....................................................A-1
Safety Precautions.................................................................................................A-2
Select Suitable Location........................................................................................A-2
Stacking ..........................................................................................................A-2
Tilting...............................................................................................................A-2
Input and Grounding Connections ..................................................................A-2
Power Cord Connection..................................................................................A-2
Undercarriage Mountings................................................................................A-2
Output Cables, Connections and Limitations.........................................................A-3
Negative Electrode Polarity ...................................................................................A-3
Voltage Sensing ............................................................................................A-3, A-4
Power Wave to Semi-automatic Power Feed Wire Feeder Interconnections........A-4
System Description................................................................................................A-5
System Set-Up.........................................................................................A-6 thru A-8
Welding with Multiple Power Waves......................................................................A-9
Control Cable Specifications..................................................................................A-9
I / O Receptacle Specifications............................................................................A-10
Dip Switch Settings and Locations...............................................................A-10
Control Board Dip Switch..............................................................................A-10
________________________________________________________________________
Operation.........................................................................................................Section B
Safety Precautions.................................................................................................B-1
General Description...............................................................................................B-1
Recommended Processes and Equipment ...........................................................B-1
Recommended Processes..............................................................................B-1
Required Equipment .......................................................................................B-2
Limitations.......................................................................................................B-2
Duty Cycle and Time Period ...........................................................................B-2
Case Front Controls ................................................................................B-2, B-3
Nominal Procedures........................................................................................B-3
Fringe Procedures...........................................................................................B-3
Making a Weld ................................................................................................B-3
Welding Adjustment........................................................................................B-3
Constant Voltage Welding...............................................................................B-4
Pulse Welding, Tig GTAW ..............................................................................B-5
Pulse on Pulse, Benefits on Pulse on Pulse, Tig GTAW ................................B-6
Power Mode, Recommended Welding Procedures for Power Mode..............B-7
________________________________________________________________________
Accessories.....................................................................................................Section C
Optional Equipment...............................................................................................C-1
Factory Installed..............................................................................................C-1
Field Installed..................................................................................................C-1
Compatible Lincoln Equipment
________________________________________________________________________
Maintenance ....................................................................................................Section D
Safety Precautions ................................................................................................D-1
Capacitor Discharge Procedure ............................................................................D-1
Routine Maintenance.............................................................................................D-1
Periodic Maintenance............................................................................................D-1
Calibration Specification........................................................................................D-1
________________________________________________________________________
Troubleshooting..............................................................................................Section E
How to use Troubleshooting Guide .......................................................................E-1
Using the Status LED to Troubleshoot System Problems.....................................E-2
Troubleshooting Guide.............................................................................E-3 thru E-7
________________________________________________________________________
Wiring Diagram ............................................................................................Section F-1
Connection Diagram....................................................................................Section F-2
Dimension Print............................................................................................Section F-3
________________________________________________________________________
Parts Lists...............................................................................................................P 418
________________________________________________________________________

A-1
INSTALLATION
POWER WAVE 405
A-1
TECHNICAL SPECIFICATIONS - POWER WAVE 405
INPUT AC VOLTAGE & DC OUTPUT
OUTPUT CABLES, CONNECTIONS AND LIMITATIONS
Product Ordering Input AC Rated DC Output Output Weight Dimensions
Name Information Voltage Amps/Volts/Duty Cycle Range with Cord HxWxD
50/60 Hz (continuous)
350A / 34V / 60% 14.7”x12.5”x
Power 200-220/ 3 Phase 27.8”*
Wave K 2152-2 380-400/ 320A / 33V / 60% AMPS 86.5lbs (373x318x
405 415 1 Phase 5-425 (37.4 kg) 706*)mm
60/50 Hz
275A / 31V /100%
1 Phase
300A / 32V / 100% * Includes
3 Phase handles
* Overall Length Including Handle, 21.6” (549mm) without handle.
Select the output cable size based upon the following chart.
Cable sizes for Combined Length of Electrode and Work Cable (Copper) 75C rated:
DUTY CYCLE CURRENT LENGTH UP 61m (200 FT) 61-76m (200-250 FT)
100% 275 2/0 2/0
60% 350 2/0 2/0
INPUT CURRENT
2. When operating on these inputs, the line cord should be changed to an input conductor of 6 AWG or larger.
1. Not rated is indicated by 4-x's in the box on the rating plate
Recommended Fuse Sizes Based On The U.S. National Electrical Code And Maximum Machine Outputs
Input 50/60 Hz Output Recommended
Voltage Phases 300Amps@ 350Amps@ Line Cord Size Fuse Size Notes
32Volts(100%) 34Volts(60%) AWG SIZES
200 3 41 48 6 80A Note 2
230 3 37 48 6 80A Note 2
380 3 23 28 8 50A
400 3 22 27 8 50A
415 3 22 26 8 50A
Voltage Phases 275Amps@ 320Amps@ Line Cord Size Fuse Size Notes
31Volts(100%) 33Volts(60%)
200 1 ---- ---- --- ----- Note 1
220 1 64 82 4 125A Note 2
380 1 44 55 6 80A Note 2
400 1 40 50 8 80A
415 1 38 48 8 80A

A-2
INSTALLATION
POWER WAVE 405
A-2
SELECT SUITABLE LOCATION
The Invertec POWER WAVE 405 will operate in harsh
environments. Even so, it is important that simple pre-
ventative measures are followed in order to assure
long life and reliable operation.
•The machine must be located where there is free cir-
culation of clean air such that air movement in the
back, out the sides and bottom will not be restricted.
•Dirt and dust that can be drawn into the machine
should be kept to a minimum. Failure to observe
these precautions can result in excessive operating
temperatures and nuisance shutdown.
•Keep machine dry. Shelter from rain and snow. Do
not place on wet ground or in puddles.
•DO NOT MOUNT OVER COMBUSTIBLE SURFACES.
Where there is a combustible surface directly
under stationary or fixed electrical equipment,
that surface shall be covered with a steel plate at
least .06”(1.6mm) thick, which shall extend not
less than 5.90”(150mm) beyond the equipment on
all sides.
-----------------------------------------------------------------------
STACKING
POWER WAVE 405 cannot be stacked.
TILTING
Place the machine directly on a secure, level surface
or on a recommended undercarriage. The machine
may topple over if this procedure is not followed.
INPUT AND GROUNDING CONNECTIONS
•Only a qualified electrician should connect the
Invertec POWER WAVE 405. Installation should be
made in accordance with the appropriate National
Electrical Code, all local codes and the information
detailed below.
•When received directly from the factory, multiple
voltage machines are internally connected for
400VAC. If 400VAC is the desired input, then the
machine may be connected to the power system
without any setup required inside the machine.
SAFETY PRECAUTIONS
ELECTRIC SHOCK can kill.
•TURN THE INPUT POWER OFF AT
THE DISCONNECT SWITCH BEFORE
ATTEMPTING TO CONNECT OR DIS-
CONNECT INPUT POWER LINES,
OUTPUT CABLES, OR CONTROL CABLES.
•Only qualified personnel should perform this
installation.
•Connect the green/yellow lead of the power
cord to ground per U.S.National Electrical
Code.
----------------------------------------------------------------------
WARNING
•Initial 200VAC - 230VAC operation will require an
Input voltage panel setup.
•Open the access panel on the rear of the machine.
•For 200 or 230: Position the large switch to 200-
230.
For higher voltages: Position the large switch to
greater than 380.
•Move the "A" lead to the appropriate terminal.
POWER CORD CONNECTION
A 5 meter power cord is provided and wired into the
machine. Follow the power cord connection instruc-
tions.
•Incorrect connection may result in equipment
damage.
-----------------------------------------------------------------------
Single Phase Input
Connect green/yellow lead to ground per National
Electrical Code.
Connect blue and brown leads to power.
Wrap black lead with tape to provide 600V insulation.
Three Phase Input
Connect green/yellow lead to ground per National
Electric Code.
Connect black, blue and brown leads to power.
UNDERCARRIAGE MOUNTINGS
WARNING
WARNINGAVISODE
PRECAUCION
ATTENTION
!!
!!
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetuer adipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquameratat
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquamerat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetuer adipiscing
elit,eddiamnon elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer laoreetdoloremagnaaliquam erat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetuer adipiscing
elit,eddiamnon elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer laoreetdoloremagnaaliquamerat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquamerat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetuer adipiscing
elit,eddiamnon elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquamerat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetuer adipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer laoreetdoloremagnaaliquam erat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitamet consectetueradipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquam erat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitamet consectetueradipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquamerat
at
Loremipsumdolorsitametconsectetueradipiscing Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquam erat
at
Loremipsumdolorsitametconsectetuer adipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer laoreetdoloremagnaaliquamerat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitamet consectetuer adipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer laoreetdoloremagnaaliquam erat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitamet consectetuer adipiscing
elit,eddiamnon elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer laoreetdoloremagnaaliquamerat
at
Loremipsumdolorsit amet consectetuer adipiscing Loremipsumdolorsitamet consectetuer adipiscing
elit,eddiam non elit,eddiam nonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagna aliquamer laoreetdoloremagnaaliquam erat
at
Loremipsumdolorsitamet consectetuer adipiscing
Loremipsumdolorsit amet consectetuer adipiscing
elit,eddiam non
elit,eddiamnonummummynibheuismod tincidunt ut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquam er laoreetdoloremagna aliquamerat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetuer adipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagna aliquam er laoreetdoloremagna aliquam erat
at
Loremipsumdolorsitametconsectetuer adipiscing
Loremipsumdolorsitamet consectetueradipiscing
elit,eddiamnon elit,eddiam nonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquam er
laoreetdoloremagna aliquam erat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon
elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquam erat
at
Loremipsumdolorsitametconsectetueradipiscing
Loremipsumdolorsitametconsectetueradipiscing
elit,eddiamnon elit,eddiamnonumm
ummynibheuismodtinciduntut
ynibheuismodtinciduntut
laoreetdoloremagnaaliquamer
laoreetdoloremagnaaliquameratat
WARNING
REMOTEPOWER
OFF
ON
P O W E R W A V E 3 5 5
GREEN / YELLOW
BLUE
BLACK
BROWN
5.50
10.00
MOUNTING HOLE LOCATIONS
M19527
1/4-20 NUT (4 PLACES)
NOTE: MOUNTING SCREWS CA
10/01
N NOT PROTRUDE MORE THAN
0.5 INCHES INSIDE THE MACHINE.
11.84
3.50
CAUTION
CAUTION

NEGATIVE ELECTRODE POLARITY
When negative electrode polarity is required, such as
in some Innershield applications, reverse the output
connections at the power source (electrode cable to
the negative (-) Twist-Mate terminal, and work cable
to the positive (+) Twist-Mate terminal.
When operating with negative electrode polarity the
"Electrode Sense Polarity" DIP switch must be set to
the "Negative" position on the Wire Drive Feed Head
PC Board. The default setting of the switch is positive
electrode polarity. Consult the Power Feed instruction
manual for further details.
VOLTAGE SENSING
The best arc performance occurs when the
PowerWaves have accurate data about the arc condi-
tions. Depending upon the process, inductance within
the electrode and work lead cables can influence the
voltage apparent at the studs of the welder. Voltage
sense leads improve the accuracy of the arc condi-
tions and can have a dramatic effect on performance.
Sense Lead Kits (K940-10, -25 or -50) are available
for this purpose.
If the voltage sensing is enabled but the sense
leads are missing, improperly connected, or if the
electrode polarity switch is improperly configured,
extremely high welding outputs may occur.
------------------------------------------------------------------------
The ELECTRODE sense lead (67) is built into the
control cable, and is automatically enabled for all
semi-automatic processes. The WORK sense lead
(21) connects to the Power Wave at the four pin con-
nector. By default the WORK voltage is monitored at
the output stud in the POWER WAVE 405. For more
information on the WORK sense lead (21), see"Work
Voltage Sensing”in the following paragraph.
A-3
INSTALLATION
POWER WAVE 405
A-3
OUTPUT CABLES, CONNECTIONS AND
LIMITATIONS
Connect a work lead of sufficient size and length
between the proper output terminal on the power
source and the work. Be sure the connection to the
work makes tight metal-to-metal electrical contact. To
avoid interference problems with other equipment and
to achieve the best possible operation, route all cables
directly to the work or wire feeder. Avoid excessive
lengths and do not coil excess cable.
When using an inverter type power source like the
Power Waves, use the largest welding (electrode
and work) cables that are practical. At least 2/0
copper wire - even if the average output current
would not normally require it. When pulsing, the
pulse current can reach very high levels. Voltage
drops can become excessive, leading to poor
welding characteristics, if undersized welding
cables are used.
------------------------------------------------------------------------
Most welding applications run with the electrode being
positive (+). For those applications, connect the elec-
trode cable between the wire feeder and the positive
(+) output Twist-Mate terminal on the power source.
Connect the other end of the electrode cable to the
wire drive feed plate. The electrode cable lug must be
against the feed plate. Be sure the connection to the
feed plate makes tight metal-to-metal electrical con-
tact. The electrode cable should be sized according to
the specifications given in the output cable connec-
tions section. Connect a work lead from the negative
(-) power source output Twist-Mate terminal to the
work piece. The work piece connection must be firm
and secure, especially if pulse welding is planned.
For additional Safety information regarding the elec-
trode and work cable set-up, See the standard "SAFE-
TY INFORMATION" located in the front of the
Instruction Manuals.
Excessive voltage drops caused by poor work
piece connections often result in unsatisfactory
welding performance.
------------------------------------------------------------------------
CAUTION
CAUTION
CAUTION

5. Replace the wrap around and screws. The PC
board will “read”the switch at power up, and config-
ure the work voltage sense lead appropriately.
ELECTRODE VOLTAGE SENSING
Enabling or disabling electrode voltage sensing is
automatically configured through software. The 67
electrode sense lead is internal to the cable to the
wire feeder and always connected when a wire feeder
is present.
Important: The electrode polarity must be config-
ured at the feed head for all semi-automatic
processes. Failure to do so may result in extreme-
ly high welding outputs.
------------------------------------------------------------------------
POWER WAVE TO SEMI-AUTOMATIC
POWERFEED WIRE FEEDER INTERCON-
NECTIONS
The POWER WAVE 405 and semi-automatic
PowerFeed family communicate via a 5 conductor
control cable (K1543). The control cable consists of
two power leads, one twisted pair for digital communi-
cation, and one lead for voltage sensing. The cables
are designed to be connected end to end for ease of
extension. The output receptacle on the POWER
WAVE 405 is on the case front. The input receptacle
on the Power Feed is typically located at the back of
the feeder, or on the bottom of the user interface.
Due to the flexibility of the platform the configuration
may vary. The following is a general description of the
system. For specific configuration information, consult
the semi-automatic Power Feed instruction manual.
A-4
INSTALLATION
POWER WAVE 405
A-4
Enable the voltage sense leads as follows:
TABLE A.1
Process Electrode Voltage Work Voltage
Sensing 67 lead * Sensing 21 lead
GMAW 67 lead required 21 lead optional
GMAW-P 67 lead required 21 lead optional
FCAW 67 lead required 21 lead optional
GTAW
Voltage sense at studs Voltage sense at studs
SMAW Voltage sense at studs Voltage sense at studs
SAW 67 lead required 21 lead optional
CAC-C Voltage sense at studs Voltage sense at studs
* The electrode voltage 67 sense lead is integral to the
control cable to the wire feeder.
Work Voltage Sensing
The standard POWER WAVE 405’s default to the
work stud (work sense lead disabled)
For processes requiring work voltage sensing, con-
nect the (21) work voltage sense lead (K940) from the
Power Wave work sense lead receptacle to the work
piece. Attach the sense lead to the work piece as
close to the weld as practical, but not in the return cur-
rent path of the electrode to the ground clamp. Enable
the work voltage sensing in the Power Wave as fol-
lows:
• Do not touch electrically live parts or
electrodes with your skin or wet
clothing.
• Insulate yourself from the work and
ground.
• Always wear dry insulating gloves.
-----------------------------------------------------------
1. Turn off power to the power source at the discon-
nect switch.
2. Remove the wrap around cover from the power
source.
3. The control board is on the center assembly facing
the case front. Locate the 8-position DIP switch and
look for switch 8 of the DIP switch.
4. Using a pencil or other small object, slide the switch
to the OFF position if the work sense lead is NOT
connected. Conversely, slide the switch to the ON
position if the work sense lead is present.
WARNING
O
N12345678
CAUTION

A-5
INSTALLATION
POWER WAVE 405
A-5
SYSTEM DESCRIPTION
The POWER WAVE 405 and Power Feed family of
products utilize a digital communication system called
Linc-Net. Simply put, Linc-Net allows large amounts of
information to be passed at very high speeds between
components (nodes) in the system. The system
requires only two wires for communication, and
because of its bus-like structure, the components may
be connected to the network in any order, thus simpli-
fying the system set-up.
Each "system" must contain only one power source.
The power source may be connected to a maximum
of four feeder groups. Each group containing one user
interface (UI), and up to seven Feed Heads (FH). SEE
FIGURE A.1. The UI controls all of the FH’s of that
group. The UI’s and FH’s are assigned to groups by
setting a code on the DIP switches mounted on their
individual control boards. For example all of the FH’s
to be controlled by a given UI must have their "Group
ID" switches set to the same group number as the UI.
In addition, each FH must be assigned a separate FH
number within that group. See the system set-up sec-
tion for further details.
From a network perspective, each component in the
system is considered a separate node, regardless of
its physical location. For example, even though a UI
and FH may be physically mounted together, they are
still viewed as separate pieces (nodes) by the net-
work, and can only communicate via Linc-Net. The
Linc-Net connection is generally made external
through the Linc-Net Control Cable, but can also be
made internally, as with the PF-10 bench model feed-
er.
The most common Linc-Net configuration (called a
simple system) consists of one power source, one
user interface and one feeder. Under these circum-
stances the group and feed head ID DIP switches are
ignored and the system will function regardless of
their position. The same is true for the minimum sys-
tem consisting of a power source and one UI
(Example: a stick welding system).
FIGURE A.1
System Model
405

A-6
INSTALLATION
POWER WAVE 405
A-6
FIGURE A.2
Simple System
SYSTEM SET-UP
Basic Rules
•Each group is required to have one user interface.
No group may have more than one user interface.
•Each group can have up to seven Feed Heads.
Exception: Group 3 is limited to a maximum of six
Feed Heads.
•Each system has only one power source. For net-
work purposes, the PS belongs to Group 3, which is
why group 3 is only allowed 6 feed heads in addition
it’s user interface.
•No two feed heads can have identical Group and
Feed Head numbers.
•Group and Feed Head ID numbers must be set on
the appropriate dipswitches at each node. Consult
the appropiate Power Feed Wire Feeder Instruction
Manual for specific details regarding dipswitch set-
tings.
•Feed head “0”not allowed. Exception: Simple sys-
tem ignores all ID numbers, therefore “FH0”will
function.
•Each node must be connected to the Linc-Net com-
munication network. The order of connection is not
important, as each node is identified by it’s unique
Group and Feed Head ID number as defined on it’s
dipswitches. See Figures A.2 thru A.5.
Group and Feed
Head ID numbers are
ignored in a simple
system.
405

A-7
INSTALLATION
POWER WAVE 405
A-7
FIGURE A.3
Multiple Group System
No “FH0”Alllowed!
FIGURE A.4
Single Group Multi-Head System
No “FH0”Alllowed!
The Dual Head
option allows the abil-
ity to maintain 2 sets
of procedures. If
more then 2 heads
are used, odd #’s use
FH1 settings, even
#’s use FH2 settings.
405
405

A-8
INSTALLATION
POWER WAVE 405
A-8
FIGURE A.5
Single Group Multi-Head System (Alternate Method) No “FH0”Alllowed!
When a standard
User Iterface is used
in a group with multi-
ple Feed Heads, all
of the Feed Heads
use a single set of
procedures.
405

A-9
INSTALLATION
POWER WAVE 405
A-9
WELDING WITH MULTIPLE POWER
WAVES
Special care must be taken when more than one
Power Wave is welding simultaneously on a single
part. Arc blow and arc interference may occur or
be magnified.
Each power source requires a work lead from the
work stud to the welding fixture. Do not combine all of
the work leads into one lead. The welding travel direc-
tions should be in the direction moving away from the
work lead as shown below. Connect all of the work
sense leads from each power source to the work
piece at the end of the weld.(See Figure A.6)
For the best results when pulse welding, set the wire
size and wire feed speed the same for all the Power
Waves. When these parameters are identical, the
pulsing frequency will be the same, helping to stabilize
the arcs.
Every welding gun requires a seperate shielding gas
regulator for proper flow rate and shielding gas cover-
age.
Do not attempt to supply shielding gas for two or more
guns from only one regulator.
If an anti-spatter system is in use then each gun must
have its own anti-spatter system.
Connect All Work
Sense Leads at the End
of the Joint
Connect All Welding
Work Leads at the
Beginning of the Joint
Travel
Direction
P
POWER WAVE 405
POWER WAVE 405
TWO POWER WAVES
CONTROL CABLE SPECIFICATIONS
It is recommended that genuine Lincoln control cables
be used at all times. Lincoln cables are specifically
designed for the communication and power needs of
the Power Wave / Power Feed system.
The use of non-standard cables, especially in
lengths greater than 25 feet, can lead to communi-
cation problems (system shutdowns), poor motor
acceleration (poor arc starting) and low wire dri-
ving force (wire feeding problems).
------------------------------------------------------------------------
The K1543 series of control cables can be connected
end to end for ease of extension. Do not exceed more
than 100 feet (30.5 m) total control cable length.
CAUTION
CAUTION
FIGURE A.6

A-10
INSTALLATION
POWER WAVE 405
A-10
I / O RECEPTACLE SPECIFICATIONS
TABLE A.2
WIRE FEEDER RECEPTACLE
PIN LEAD# FUNCTION
A 53 Communication Bus L
B 54 Communication Bus H
C 67A Electrode Voltage Sense
D 52 0vdc
E 51 +40vdc
TABLE A.3
VOLTAGE SENSE RECEPTACLE
PIN LEAD# FUNCTION
3 21A Work Voltage Sense
TABLE A.4
RS232 RECEPTACLE
PIN LEAD# FUNCTION
2 253 RS232 Receive
3 254 RS232 Transmit
4 # Pin5
5 # Pin4
6 # # Pin20
20 # # Pin6
7 251 RS232 Commom
DIP SWITCH SETTINGS AND LOCATIONS
DIP switches on the P.C. Boards allow for custom
configuration of the Power Wave. To access the DIP
switches:
ELECTRIC SHOCK can kill.
1. Turn off power to the power source at
the disconnect switch.
------------------------------------------------------------------------
2. Remove the wrap around cover from the power
source.
3. The control board is on the center assembly facing
the case front. Locate the 8-position DIP switch and
look for switch 8 of the DIP switch.
4. Using a pencil or other small object, slide the switch
to the OFF position if the work sense lead is NOT
connected. Conversely, slide the switch to the ON
position if the work sense lead is present.
5. Replace the wrap around and screws. The PC
board will “read”the switch at power up, and config-
ure the work voltage sense lead appropriately.
CONTROL BOARD DIP SWITCH:
switch 1 = reserved for future use
switch 2 = reserved for future use
switch 3 = reserved for future use
switch 4 = reserved for future use
switch 5 = reserved for future use
switch 6 = reserved for future use
switch 7 = reserved for future use
switch 8* = work sense lead
switch 8* work sense lead
off work sense lead not connected
on work sense lead connected
*Factory setting for Switch 8 is OFF.
CONTROL BOARD (DIP Switch Location)
FIGURE A.7
O
N12345678
WARNING

GENERAL DESCRIPTION
The Power Wave semi-automatic power source is
designed to be a part of a modular, multi-process
welding system. Depending on configuration, it can
support constant current, constant voltage, constant
power and pulse welding modes.
The Power Wave power source is designed to be
used with the semi automatic family of Power Feed
wire feeders, operating as a system. Each component
in the system has special circuitry to "talk with" the
other system components, so each component (power
source, wire feeder, user interface) knows what the
other is doing at all times. These components commu-
nicate with Linc-Net.
The POWER WAVE 405 is a high performance, digi-
tally controlled inverter welding power source capable
of complex, high-speed waveform control. Properly
equipped, it can support the Constant Power, GMAW,
GMAW-P, Pulse on Pulse, FCAW, SMAW, GTAW,
and CAC-A processes. It carries an output rating of
350 Amps, 34 Volts at 60% duty cycle and 300 Amps,
32 volts at 100% duty cycle.
RECOMMENDED PROCESSES AND
EQUIPMENT
RECOMMENDED PROCESSES
The POWER WAVE 405 can be set up in a number of
configurations, some requiring optional equipment or
welding programs. Each machine is factory prepro-
grammed with multiple welding procedures, typically
including Constant Power, GMAW, GMAW-P, Pulse
on Pulse, FCAW, GTAW, and CAC-A for a variety of
materials, including mild steel, stainless steel, cored
wires, and aluminum.
The POWER WAVE 405 is recommended for semi-
automatic welding, and may also be suitable for basic
hard automation applications.
•This Power Wave is not recommended for processes
other than those listed.
B-1
OPERATION
B-1
POWER WAVE 405
SAFETY PRECUATIONS
Read this entire section of operating instructions
before operating the machine.
ELECTRIC SHOCK can kill.
• Unless using cold feed feature, when
feeding with gun trigger, the elec-
trode and drive mechanism are
always electrically energized and
could remain energized several sec-
onds after the welding ceases.
• Do not touch electrically live parts or electrodes
with your skin or wet clothing.
• Insulate yourself from the work and ground.
• Always wear dry insulating gloves.
-----------------------------------------------------------
FUMES AND GASES can be dangerous.
• Keep your head out of fumes.
• Use ventilation or exhaust to remove
fumes from breathing zone.
-----------------------------------------------------------
WELDING SPARKS can cause fire or
explosion.
• Keep flammable material away.
• Do not weld on containers that have
held combustibles.
-----------------------------------------------------------
ARC RAYS can burn.
• Wear eye, ear, and body protection.
Observe additional guidelines detailed in the
beginning of this manual.
WARNING