Linear Analog Devices LTM4664 User manual

1
DEMO MANUAL DC2672A-B
Rev. 0
DESCRIPTION
LTM4664
48VIN, Single 50A µModule Regulator
With Digital Power System Management
Demonstration circuit 2672A-B is a complete non-isolated
48V input, dual-phase single output, high efficiency, high
density µModule regulator with 30V to 58V input range.
The output can supply 50A maximum load current. The
demo board has a LTM4664 µModule regulator, which is
a dual 25A or single 50A step-down regulator with digital
power system management. Please see LTM4664 data-
sheet for more detailed information.
DC2672A-B powers up to default settings and produces
power based on configuration resistors without the need
for any serial bus communication. This allows easy evalu-
ation of the DC/DC converter. To fully explore the extensive
power system management features of the part, download All registered trademarks and trademarks are the property of their respective owners.
the GUI software LTpowerPlay™onto your PC and use
ADI’s I2C/SMBus/PMBus dongle DC1613A to connect to
the board. LTpowerPlay allows the user to reconfigure the
part on the fly and store the configuration in EEPROM, view
telemetry of voltage, current, temperature and fault status.
GUI Download
The software can be downloaded here.
For more details and instructions of LTpowerPlay, please
refer to LTpowerPlay GUI for LTM4664 Quick Start Guide.
Design files for this circuit board are available.
BOARD PHOTO
Figure1. Dual Phase Single-output LTM4664/DC2672A-B Demo Circuit

2
DEMO MANUAL DC2672A-B
Rev. 0
QUICK START PROCEDURE
Demonstration circuit 2672A-B is easy to set up to evalu-
ate the performance of the LTM4664. Refer to Figure2
for the proper measurement equipment setup and follow
the procedure below.
1. With power off, connect the input power supply to VIN
(30V-58V) and GND (input return).
2. Connect the 1.0V output load between VOUT0 and GND
(Initial load: no load).
3. Connect the DVMs to the input and outputs. Set de-
fault jumper position:SW1:ON;SW2:ON;SW3:ON;
JP1: OFF; JP2: EXT.
4. Turn on the input power supply and check for the
proper output voltages. VOUT0 should be 1.0V±0.5%.
5. Once the proper output voltages are established, adjust
the loads within the operating range and observe the
output voltage regulation, ripple voltage and other
parameters.
6. Connect the dongle and control the output voltages
from the GUI. See “LTpowerPlay GUI for the LTM4664
Quick Start Guide” for details.
Note:When measuring the output or input voltage rip-
ple, do not use the long ground lead on the oscilloscope
probe. See Figure3 for the proper scope probe technique.
Short, stiff leads need to be soldered to the (+) and (−)
terminals of an output capacitor. The probe’s ground ring
needs to touch the (−) lead and the probe tip needs to
touch the (+) lead.
Table1. LTM4664 Demo Boards for up to 200A Point-of-Load Regulation
MAXIMUM OUTPUT CURRENT NUMBER OF OUPUTS
NUMBER OF LTM4664 µMODULE
REGULATORS ON THE BOARD DEMO BOARD NUMBER
25A 2 1 DC2672A-A
50A 1 1 DC2672A-B
100A 1 2 DC2954A-A
150A 1 3 DC2954A-B
200A 1 4 DC2954A-C
PERFORMANCE SUMMARY
Specifications are at TA= 25°C
PARAMETER CONDITIONS VALUE
Input Voltage Range 30V to 58V
Output Voltage, VOUT0 VIN = 30-58V, IOUT0 = 0A to 50A 0.5 to 1.5V, Default: 1.0V
Maximum Output Current, IOUT0 VIN = 30-58V, VOUT0 = 0.5V to 1.5V 50A
Typical Efficiency VIN = 48V, VOUT0 = 1.0V, IOUT0 = 50A 87.1% (See Figure5)
Default Switching Frequency 250kHz

3
DEMO MANUAL DC2672A-B
Rev. 0
QUICK START PROCEDURE
Figure2. Proper Measurement Equipment Setup

4
DEMO MANUAL DC2672A-B
Rev. 0
QUICK START PROCEDURE
VOUT GND
COUT
Figure3. Measuring Output Voltage Ripple
Figure4. Demo setup with PC
Connecting a PC to DC2672A-B
You can use a PC to reconfigure the power manage-
ment features of the LTM4664 such as:nominal V
OUT
,
margin set points, OV/UV limits, temperature fault limits,
sequencing parameters, the fault log, fault responses,
GPIOs and other functionalities. The DC1613A dongle
may be plugged when VIN is present.
USB to I2C/PMBus
Dongle DC1613A
LTM4664 Demo
Board DC2672A-B
Input Power
Supply
USB Cable VIN
12-PIN (J11)
Connector
Load0
Vout0
VIN = 48V
VIN = 30V
VIN = 58V
LOAD CURRENT (A)
0
10
20
30
40
50
60
65
70
75
80
85
90
95
EFFICIENCY (%)
Efficiency vs Load at VOUT0 = 1.0V
Figure5. Efficiency vs. load current

5
DEMO MANUAL DC2672A-B
Rev. 0
QUICK START PROCEDURE
Figure6. VOUT0 Load Transient Response at VIN = 48V, VOUT0 = 1.0V
100μs/DIV
VOUT0 (20MHz BW)
20mV/DIV
0A-12.5A
LOAD STEP
Figure7. VOUT0 Voltage Ripple at VIN = 48V, VOUT0 = 1.0V, IOUT0 = 50A
100μs/DIV
VOUT0 (20MHz BW)
10mV/DIV
Figure8. Thermal at VIN = 48V, VOUT0 = 1.0V, IOUT0 = 50A, TA= 25°C, No Airflow

6
DEMO MANUAL DC2672A-B
Rev. 0
QUICK START PROCEDURE
Figure9. LTpowerPlay Main Interface
LTpowerPlay Software GUI
LTpowerPlay is a powerful Windows based development
environment that supports Analog Devices power sys-
tem management ICs and μModules, including LTM4675,
LTM4676, LTM4677, LTM4678, LTM4680, LTM4700,
LTM4664, LTC3880, LTC3882, LTC3883 and LTC3884.
The software supports a variety of different tasks. You
can use LTpowerPlay to evaluate Analog Devices ICs by
connecting to a demo board system. LTpowerPlay can
also be used in an offline mode (with no hardware pres-
ent) in order to build a multichip configuration file that
can be saved and reloaded at a later time. L
TpowerPlay
provides unprecedented diagnostic and debug features. It
becomes a valuable diagnostic tool during board bring-up
to program or tweak the power management scheme in
a system, or to diagnose power issues when bringing up
rails. LTpowerPlay utilizes the DC1613A USB-to-SMBus
controller to communicate with one of many potential tar-
gets, including LTM4675, LTM4676, LTM4677, LTM4678,
LTM4680, LTM4700, LTM4664, LTC3880, LTC3882,
LTC3883 and LTC3884’s demo system, or a customer
board. The software also provides an automatic update
feature to keep the software current with the latest set
of device drivers and documentation. The LTpowerPlay
software can be downloaded here.
To access technical support documents for LTC Digital
Power Products visit the LTpowerPlay Help menu. Online
help also available through the LTpowerPlay.

7
DEMO MANUAL DC2672A-B
Rev. 0
QUICK START PROCEDURE
QUICK START PROCEDURE
LTpowerPlay Quick Start Procedure
The following procedure describes how to use LTpow-
erPlay to monitor and change the settings of LTM4664.
1.Download and install the LTPowerPlay GUI:
2. Launch the LTpowerPlay GUI.
a. The GUI should automatically identify the DC2672A-B.
The system tree on the left hand side should look like this:
b. A green message box shows for a few seconds in the
lower left hand corner, confirming that LTM4664 is com-
municating:
c. In the Toolbar, click the “R” (RAM to PC) icon to read
the RAM from the LTM4664. This reads the configuration
from the RAM of LTM4664 and loads it into the GUI.
d. If you want to change the output voltage to a differ-
ent value, like 1.5V. In the Config tab, type in 1.5 in the
VOUT_COMMAND box, like this:
Then, click the “W” (PC to RAM) icon to write these regis-
ter values to the LTM4664. After finishing this step, you
will see the output voltage will change to 1.5V.
If the write is successful, you will see the following message:
e. You can save the changes into the NVM. In the tool bar,
click “RAM to NVM” button, as following
f. Save the demo board configuration to a (*.proj) file. Click
the Save icon and save the file. Name it whatever you want.

8
DEMO MANUAL DC2672A-B
Rev. 0
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART, NUMBER
Required Circuit Components
1 4 COUT1, COUT2, COUT9, COUT12, CAP, 1210 100uF 20% 6.3V X5R AVX, 12106D107MAT2A
2 8 COUT3, COUT4, COUT5, COUT6, CAP, 1210 330uF 20% 4V X5R TAIYO YUDEN, AMK325ABJ337MM-P
COUT10, COUT13, COUT14,
COUT15
3 2 C1, C19 CAP, 0603 3900pF 5% 50V C0G KEMET, C0603C392J5GACAUTO
4 4 C2, C3, C56, C57 CAP, 1210 22uF 20% 25V X7R AVX, 12103C226MAT2A
5 18 C4, C5, C9, C10, C11, C12, C13, CAP, 1210 10uF 10% 50V X7R MURATA, GRM32ER71H106KA12L
C14, C20, C21, C23, C24, C25,
C26, C27, C28, C29, C30
6 2 C8, C22 CAP, 22pF, C0G, 50V, 5%, 0603 AVX, 06035A220JAT2A
7 2 C16, C43 CAP, 0603 0.47uF 10% 16V X7R KEMET, C0603C474K4RAC7800
8 6 C17, C18, C31, C32, C41, C42 CAP, 0603 4.7uF 20% 25V X5R TDK, C1608X5R1E475M080AC
9 1 C34 CAP, 33uF 20% 80V ALUM. PANASONIC, EEHZC1K330P
10 6 C35, C36, C37, C38, C39, C40 CAP, 1210 2.2uF 10% 100V X7R MURATA, GRM32ER72A225KA35L
11 1 C44 CAP, 0.01uF, X7R, 16V, 10%, 0603 AVX, 0603YC103KAT2A
12 1 RS1 RES, 1206 0.002 OHMS 1% 1W PANASONIC, ERJMP2MF2M0U
13 1 RS3 RES, 1206 0.01 OHMS 1% 1W PANASONIC, ERJMP2MF10MU
14 2 R1, R7 RES, 0603 10 OHMS 1% 1/10W VISHAY, CRCW060310R0FKEA
15 12 R4, R13, R17, R18, R58, R59, RES, 0603 0 OHMS JUMPER VISHAY, CRCW06030000Z0EA
R61, R62, R64, R65, R67, R117
16 16 R9, R10, R25, R26, R27, R28, RES, 0603 10k OHMS 1% 0.1W VISHAY, CRCW060310K0FKEA
R29, R30, R31, R32, R33, R34,
R35, R36, R41, R42
17 1 R14 RES, 0603 10.5k OHMS, 1%, 1/10W VISHAY, CRCW060310K5FKEA
18 1 R19 RES, 0603 64.9k OHMS 1% 0.1W VISHAY, CRCW060364K9FKEA
19 2 R20, R37 RES, 0603 100k OHMS 1% 1/10W VISHAY, CRCW0603100KFKEA
20 1 R24 RES, 0603 75k OHMS 1% 1/10W VISHAY, CRCW060375K0FKEA
21 1 R38 RES, 100k OHMS, 1%, 1/8W, 0805,
AEC-Q200
NIC, NRC10F1003TRF
22 1 R39 RES, 0603 40.2k OHMS 1% 1/10W VISHAY, CRCW060340K2FKEA
23 1 R40 RES, 0603 4.99k OHMS, 1%, 1/10W PANASONIC, ERJ3EKF4991V
24 1 R55 RES, 0603 130k OHMS 1% 0.1W VISHAY, CRCW0603130KFKEA
25 1 R57 RES, 0603 9.76k OHMS, 1%, 1/10W VISHAY, CRCW06039K76FKEA
26 4 R60, R63, R66, R68 RES, 2010 0 OHM JUMPER VISHAY, WSL201000000ZEA9
27 1 U1 IC, Module ANALOG DEVICES, LTM4664EY

9
DEMO MANUAL DC2672A-B
Rev. 0
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART, NUMBER
Additional Demo Board Circuit Components
1 0 COUT7, COUT8, COUT11, CAP, 7343 OPTION OPTION
COUT16
2 0 C15 CAP, 0603 OPTION OPTION
3 0 D1 DIODE, OPTION OPTION
4 0 D3, D4 DIODE, SCHOTTKY 30V, 100mA OPTION CENTRAL SEMI, CMDSH-3-TR, OPTION
5 0 R2, R3, R5, R6, R11, R12, R15, R16, RES, 0603 OPTION OPTION
R21, R22, R23, R43, R44, R45, R46,
R47, R48, R49, R51, R52, R53,
R54, R56, R69, R92, R93, R95,
R97, R99, R100, R105, R106,
R107, R108, R109
6 2 R70, R71 RES, 1206 100 OHMS 1% 1/4W PANASONIC, ERJ-8ENF1000V
7 2 C45, C46 CAP, 1210 10uF 10% 16V X7R MURATA, GRM32DR71C106KA01
8 4 R72, R74, R85, R114 RES, 0603 10K OHMS 5% 1/10W VISHAY, WSL201000000ZEA9
9 1 R73 RES, 0603 34.8K OHM 1% 1/10W VISHAY, CRCW060334K8FKEA
10 1 U2 IC, REGULATOR ANALOG DEVICES, LT1761ES5-SD
11 1 R79 RES, 0603 154K OHMS 1% 1/10W VISHAY, CRCW0603154KFKEA
12 2 R80, R83 RES, 0603 20K OHMS 5% 1/10W VISHAY, CRCW060320K0JNEA
13 2 R75, R77 RES, 2010 0 OHM JUMPER VISHAY, WSL201000000ZEA9
14 4 R78, R94, R96, R98 RES, 0603 0 OHMS JUMPER VISHAY, CRCW06030000Z0EA
15 1 R82 RES, 0603 1M OHMS 5% 1/10W VISHAY, CRCW06031M00JNEA
16 1 R84 RES, 0603 681K OHMS 1% 1/10W VISHAY, CRCW0603681KFKEA
17 1 U3 IC, LTC6992 ANALOG DEVICES, LTC6992IS6-1
18 1 U4 IC, SINGLE OP AMP ANALOG DEVICES, LT1803IS5
19 2 C49, C53 CAP, 0603 100nF 20% 16V X7R AVX, 0603YC104MAT2A
20 1 R86 RES, 0603 182 OHMS 1% 1/10W VISHAY, CRCW0603182RFKEA
21 1 R90 RES, VARIABLE 5K BOURNS, 3386P-1-502-LF
22 1 R91 RES, 0603 649 OHMS 1% 1/10W VISHAY, CRCW0603649RFKEA
23 1 R81 RES, 0603 3.3 OHMS 1% 1/10W VISHAY, CRCW06033R30FKEA
24 1 R87 RES, 0603 82.5 OHMS 1% 1/10W VISHAY, CRCW060382R5FKEA
25 1 C50 CAP, 0603 150pF 5% 50V NPO AVX, 06035A151JAT2A
26 1 R76 RES, 0603 2 OHMS 5% 1/10W VISHAY, CRCW06032R00JNEA
27 1 R88 RES, 2512 0.01 OHMS 1% 1W VISHAY, WSL2512R0100FEA
28 1 Q1 XSTR, MOSFET, N-CHANNEL 40V VISHAY, SUD50N04-8M8P-4GE3
29 4 COUT21, COUT25, C51, C52 CAP, 0603 1uF 20% 25V X5R AVX, 06033D105MAT2A
30 6 COUT19, COUT20, COUT23, CAP, 1210 100uF 20% 6.3V X5R AVX, 12106D107MAT2A
COUT24, C47, C48
PARTS LIST

10
DEMO MANUAL DC2672A-B
Rev. 0
PARTS LIST
ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART, NUMBER
31 4 COUT17, COUT18, COUT22, CAP, 7343 470uF 20% 2.5V SPCAP PANASONIC, EEF-GX0E471L
COUT26
32 1 U5 IC, 24LC05-I/ST MICROCHIP, 24LC025-I/ST
33 2 R101, R102 RES, 0603 10 OHMS 5% 1/10W VISHAY, CRCW060310R0JNEA
34 2 R103, R104 RES, 0603 4.99K OHMS 1% 0.1W VISHAY, CRCW06034K99FKEA
35 3 R110, R111, R115 RES, 0603 127 OHMS 1% 1/10W VISHAY, CRCW0603127RFKEA
36 2 R112, R113 RES, 0603 200 OHMS 5% 1/10W VISHAY, CRCW0603200RJNEA
37 1 R116 RES, 0603 15.8K OHMS 1% 1/10W VISHAY, CRCW060315K8FKEA
38 1 D2 DIODE, ULTRA LOW SCHOTTKY RECTIEIER NXP SEMI., PMEG2005AEL, 315
39 2 D5, D6 LED, 0603 GREEN WURTH ELEKTRONIK, 150060GS75000
40 3 D7, D8, D9 LED, 0603 RED WURTH ELEKTRONIK, 150060SS75000
41 4 Q3, Q4, Q6, Q7 XSTR, P-CHANNEL DMOS FET DIODES INC., DMP3130L-7
42 2 Q5, Q8 XSTR, N-CHANNEL DMOS FET DIODES INC., 2N7002A-7
43 2 C54, C55 CAP, 0603 10nF 10% 25V X7R AVX, 06033C103KAT2A
Hardware: For Demo Board Only
1 33 E1, E2, E3, E4, E5, E6, E7, E8, TURRET 1.64mm MILL-MAX, 2308-2-00-80-00-00-07-0
E9, E10, E11, E12, E13, E14,
E15, E16, E17, E18, E19, E20,
E21, E22, E23, E24, E25, E26,
E27, E28, E29, E30, E31, E32,
E33
2 2 JP1, JP2 HEADER, SINGLE ROW 3PIN WURTH ELEKTRONIK, 62000311121
3 4 J1, J2, J3, J4 STUD, TEST PIN PEM, KFH-032-10
4 2 J5, J6 BANANA JACK KEYSTONE, 575-4
6 3 J7, J8, J9 CONN, BNC, 5 PINS CONNEX, 112404
6 1 J10 HEADER, 4PIN 2mm STR DL HIROSE, DF3A-4P-2DSA
7 1 J11 HEADER, 12PIN 2mm STR DL FCI, 98414-G06-12ULF
8 1 J12 CONN, SOCKET 14PIN DUAL ROW R/A SULLINSINC., NPPN072FJFN-RC
9 1 J13 HEADER, 14PIN DUAL ROW R/A MOLEX, 87760-1416
10 4 J1, J2, J3, J4 LUG RING, #10 KEYSTONE, 8205
11 4 MH1, MH2, MH3, MH4 STANDOFF, SNAP ON KEYSTONE, 8834
12 8 J1, J2, J3, J4 NUT, BRASS 10-32 PENCOM, NU1132
13 3 SW1, SW2, SW3 SWITCH, SUBMINATURE SLIDE C&K, JS202011CQN
14 4 J1, J2, J3, J4 WASHER, #10 TIN PLATED BRASS PENCOM, WA4526
15 2 XJP1, XJP2 SHUNT WURTH ELEKTRONIK, 60800213421