Linear 2GIG-TS1 Configuration guide

INSTALL INSTRUCTIONS
Thisdocumentdescribesthebasicinstallationinformationforthe2GIG‐
2GIG‐TS1andthestepsnecessaryto“pair”(orlearnin)theTouchscreen
WirelessKeypadtotheControlPanel.
Box Contents
•2GIG‐TS1
•ACPowerSupply
•ACPowerSupplyBracket
•Screwsandanchors
TIP: Theboxcontentswillvarydependingonwhetherthe2GIG‐TS1
waspurchasedaspartofakitornot.
BEFORE YOU BEGIN
Is the 900 MHz Transceiver installed in the Panel?
Forthe2GIG‐TS1tocommunicatewiththeControlPanel,the900MHz
Transceiver(2GIG‐XCVR2)mustbealreadybeinstalledintheControl
Panel.
Is the 2GIG-TS1 paired with the Control Panel?
The2GIG‐TS1andtheControlPanelhavetobepairedtocommunicate
witheachother.
To check for to see if the 2GIG-TS1 is paired with the
Control Panel
Uponpowerup,the2GIG‐TS1displaysthefollowingscreen:
2GIG-TS1 PRODUCT OVERVIEW
TheModel2GIG‐2GIG‐TS1Touc h ScreenWirelessKeypadisaremote
controldevicethatoffersthefunctionalityofasystemkeypadbutalso
extendsallusercontrolofthe2GIGControlpaneltootherlocationsina
user’shome.Usingthe2GIG‐TS1,userscancontrollights,thermostat
anddoorlocksandseethestatusofeveryzoneintheirhomeusingthe
exactsameandfamiliarinterfacefoundontheControlPanel.Thekeypad
isdesignedforindooruseonly.
IMPORTANT: NotforUL985installations.
Thepanelandbuttonsserveascontrolsaswellasindicators.
Pressingthe(Emergency)buttondisplaysemergencyiconsonthe
displayforPanic,Fire,andEmergencyalarmactivation(eachhas
programmableoptionsandcanbeenabledordisabled).Pressingthe
(Home)buttonchangesthesystemdisplaytotheHomeScreen.The
keypadispoweredfromaplug‐inpowersupply.The2GIG‐TS1exchanges
informationthroughasecure2‐waywirelessconnectionwiththeControl
Panel.
NOTE: Beforeusingthe2GIG‐TS1itmustbe“learned”intothe
ControlPanel.
Mounting Tools
Somespecialtoolsmayberequiredtomountthe2GIG‐TS1ontothe
wall:
•Screwdriver
•Pencil
•Wirestripper
•Staplegun
•Drywallsaw(orequivalent)
• Ladder
PREPARING THE KEYPAD
NOTE: Checkthatthe2GIG‐TS1Keypadisfunctioningbefore
selectingalocationfortheKeypad.
1Remove the screw.
2Flip open the back cover of the 2GIG-TS1.
3Disconnect the hanging strap.
4Use the back cover as the mounting plate.
2GI
Touch Screen Wireless Keypad
ForRemoteControlofthe2GIGSecuritySystem

2©2013 2GIG Technologies Inc. All Rights Reserved.
SELECTING A LOCATION FOR THE KEYPAD
1MakesurethatACPowerisavailablenearby.
TIP: Becarefulofstuds,electricalwiresandpipesinthewall.
2Usethekeypad’sbackcoverasatemplatetomarkthescrewholes
withapencilandthepower(wiring)accesshole.
3Useadrywallsawtocutthewiringhole.
Mounting the Keypad
1Usethe3screwsandanchorsthataresuppliedtoattachthe
mountingplatetothewall.
2Route18AWGwirebetweenthekeypadandthelocationofthe
powersupply.
Wire Size and Length
Toensureproperoperation,DoNotexceedthefollowingmaximum
lengthforthewiresizeinstalled:
Toensurethattheappropriatewiresizeandlengthareinstalled,
measurethevoltagebetweenthepowerconnectionterminalsatthe
backofthecontrolpanel.Thevoltagemeasuredmustnotfallbelow11
voltsDCornuisance“ACPowerLoss”messagesmaybedisplayedand
reported.
NOTE: IntheUnitedStates,wiringroutedinsidewalls,ceilings,and
floorsmustcomplywithrequirementsoftheNationalElectrical
Code,ANSI/NFPA70andlocalbuildingcodes.Forwiringfrom
theoutputofthe2GIGclassIIpowersupply,wiringratedCL2,
CL2X,CL2R,orPLTCisrecommendedtosatisfythese
requirements.Ifthiswiringisinstalledinanairplenum(space
usedforenvironmentalairexchange)itmustberatedCL2P
(plenumrated).
Connect the Power Wires to the Keypad
1Re‐connectthehangingstrap.
2Use#6insulatedspadeterminals(notsupplied)toconnectwires
fromthepowersupplytothekeypad.
3Closethekeypad.
4Connectthepowerwirestothepowersupply.
Wire Size Maximum Length
22AWG 55feet(16.8meters)
20AWG 85feet(25.9meters
22AWG2‐pairs
(19AWGequivalent)
110feet(33.5meters)
18AWG 135feet(41.1meters)
ASnap case closed.
BTighten case screw.
ALeft Terminal 14 VDC(+)
BRight Terminal 14 VDC (-)
C18 AWG/2-Conductor

©2013 2GIG Technologies Inc. All Rights Reserved. 3
LEARNING/PAIRING THE KEYPAD WITH THE
CONTROL PANEL
1MakesurethattheControlPanelhaspowerusingthesuppliedAC
adapterandconfirmthattheadapterisconnected.
WARNING: AControlPanelwithoutthe900MHzTransceiver
installedcannotcommunicatewiththe2GIG‐TS1.
2Makesurethatthe2GIG‐TS1haspowerfromthesuppliedAC
transformer.ConnecttheACadaptertothe2GIG‐TS1.Confirmthat
thewiresareconnectedusingthecorrectpolarity.
3Asthe2GIG‐TS1powersup,thefollowingmessageisvisibleonthe
display.
4FromtheControlPanel’sInstallerToolbox,selectSystem
Configuration.
5SelecttheGoTobutton.
6Togotoquestion4,enter04.
7SelecttheRFKeypadnumbertoassigntothe2GIG‐TS1.Usethe→
arrowtoselecttheRFKeypadnumber(1‐4).AfterselectingtheRF
Keypadnumber,pressthe↓arrowtostartconfiguringthespecific
parametersfortheRFKeypad.
8Pressthe→arroworpressthenumber1onthekeypadtogglethe
sengonthefirstquesonto“used”.Pressthe↓arrowtoconnue
configuringoptions.
9SettheRFKeypadEquipmentCodeto1059bypressingthe→arrow
until“(1059)2GIG‐TS1wirelesstouchscreenkeypad”appears.Press
the↓arrowtoadvancetothenextopon.
10 Learnthe2GIG‐TS1intotheControlPanel.Aerpressingthe↓
arrowinthepreviousstep,theLearnbuttonappears.
INITIATING THE PAIRING PROCESS
InitiatethepairingprocessattheControlPanelbypressingtheLearn
button.

4©2013 2GIG Technologies Inc. All Rights Reserved.
1OntheControlPanelpresstheLearnbutton.
2Onthe2GIG‐TS1pressthePairwithPanelbutton.
TheControlPaneldisplaysthemessage:
Pairwith2GIG‐TS1.Initiatinglearningprocess.
Whenlearningiscomplete,boththe2GIG‐TS1andControlPanel
displaythemessage:
Thelearnoperationsucceeded.
2a TheControlPaneldisplaysthemessage:
Type:2GIG‐TS1WirelessKeypadID#:X
(whereXistheRFKeypadnumberconfiguredforthe2GIG‐TS1).
2b The2GIG‐TS1displays“NetworkID:xxxx”wherexxxxisaunique
hexadecimalnumberandakeypadID.Thehexadecimalnumber
isauniquenumberassociatedwiththeControlPanelthatyou
areusing.ThekeypadIDindicatesthekeypadthatyouare
learningintotheControlPanel.
2c Tocompletethelearningprocess,presstheOKbuttononboth
theControlPanelandthe2GIG‐TS1.
3Aftersuccessfullylearningthe2GIG‐TS1intotheControlPanel,press
the↓arrowtoexitthelearningmenu.
The2GIG‐TS1displaysamessageindicatingthatthesecuritysystem
istemporarilyinoperable.The2GIG‐TS1remainsinthisstatewhile
theControlPanelisinsystemconfiguration(programming)mode.
RepeatthestepsabovetolearninadditionalTS1s.
4Toexitprogramming,clickskipthenendandexit.Uponexit,the
ControlPaneltakesaseveralsecondstoreboot.
REMOVING A 2GIG-TS1 FROM A CONTROL
PANEL (UNLEARNING THE 2GIG-TS1)
Toremovea2GIG‐TS1fromaControlPanel’sconfigurationdothe
following:
1FromtheControlPanel,gotoInstallerToolbox/System
Configuration.
2SelecttheGoTobuttonandenter04.TheControlPaneldisplays
Q4:selectRFkeypad#(1to4).Selecttheconfigured2GIG‐TS1you
wishtoremoveandpressthe↓arrow.
3MarktheRFKeypadnumberselectedas“unused”bypressingthe→
arrow.Thisactiontogglesthesettingonthefirstquestionbetween
“used”and“unused.”Pressthe↓arrowtoadvancetothenext
option.
4Toexitprogramming,clickskipthenendandexit.Uponexit,the
paneltakesseveralsecondstoreboot.
RESETTING A 2GIG-TS1 TO FACTORY
DEFAULTS
Toresetthe2GIG‐TS1todefaultssothatitmaybeusedagainon
anotherControlPanel,dothefollowing:
1Whilepowercyclingthe2GIG‐TS1,holdboththe(Emergency)
andthe(Home)buttonsdownsimultaneouslyuntiltheylightup
(approximately20seconds).Whenbothbuttonslightup,the2GIG‐
TS1hassuccessfullybeenresettoalldefaultsettings.
The2GIG‐TS1displaysthemessage:
ThisDeviceisNotPairedwithaControlPanel.
SECRET DURESS BUTTON
TIP: ThelogoonthebottomcorneroftheHomeScreendoesnot
accesstheInstallerToo lb oxonthe2GIG‐TS1.
Ifauserpressesthelogoonthebottomcornerofthe2GIG‐TS1Home
Screen,theusercanentertheduresscodeonly.Installersmust
rememberthattheInstallerToolboxcanonlybeaccessedfromthe
ControlPanel.The2GIG‐TS1cannotaccesstheInstallerToo lbox.
TIP: Althoughthereisadefaultmastercode:1111,thereisno
defaultduresscode.
Check to ensure that the 2GIG-TS1 firmware
version matches the Control Panel firmware
version
The2GIG‐TS1andtheControlPanelarerequiredtohavethesame
firmwareversiontofullycommunicatewitheachother(e.g.CPv1.10
and2GIG‐TS1v1.10).
1Fromboththe2GIG‐TS1andControlPanelHomeScreen,choose
Security/Menu/Toolbox.

©2013 2GIG Technologies Inc. All Rights Reserved. 5
2FromtheToolboxScreen,usethe→arrowunlyouseetheVersion
Screen.
2GIG-TS1 Version Screen
Control Panel Version Screen
REGULATORY INFORMATION
Wireless Product Notice
Radiocontrolsprovideareliablecommunicationslinkandfillan
importantneedinportablewirelesssignaling;however,therearesome
limitationswhichmustbeobserved.
•ForU.S.installationsonly:Theradiosarerequiredtocomplywith
FCCRulesandRegulationsasPart15devices.Assuch,theyhave
limitedtransmitterpowerandthereforelimitedrange
(approximately400ft.).
•Areceivercannotrespondtomorethanonetransmittedsignalata
timeandmaybeblockedbyradiosignalsthatoccuronorneartheir
operatingfrequencies,regardlessofcodesettings.
• ChangesormodificationstothedevicemayvoidFCCcompliance.
• Infrequentlyusedradiolinksshouldbetestedregularlytoprotect
againstundetectedinterferenceorfault.
•Ageneralknowledgeofradioanditsvagariesshouldbegainedprior
toactingasawholesaledistributorordealer,andthesefactsshould
becommunicatedtotheendusers.
FCC NOTICE
ThisdevicecomplieswithPart15oftheFCCRules.Operationissubject
tothefollowingtwoconditions:
(1)Thisdevicemaynotcauseharmfulinterference,and
(2)Thisdevicemustacceptanyinterferencereceived,including
interferencethatmaycauseundesiredoperation.
Thisequipmenthasbeentestedandfoundtocomplywiththelimitsfor
ClassBDigitalDevice,pursuanttoPart15oftheFCCRules.Theselimits
aredesignedtoprovidereasonableprotectionagainstharmful
interferenceinaresidentialinstallation.Thisequipmentgeneratesand
canradiateradiofrequencyenergyand,ifnotinstalledandusedin
accordancewiththeinstructions,maycauseharmfulinterferenceto
radiocommunications.However,thereisnoguaranteethatinterference
willnotoccurinaparticularinstallation.Ifthisequipmentdoescause
harmfulinterferencetoradioortelevisionreception,whichcanbe
determinedbyturningtheequipmentoffandon,theuserisencouraged
totrytocorrecttheinterferencebyoneormoreofthefollowing
measures.
•Reorientorrelocatethereceivingantenna
•Increasetheseparationbetweentheequipmentandreceiver
• Connecttheequipmentintoanoutletonacircuitdifferentfromthat
towhichthereceiverisconnected
•Consultthedealeroranexperiencedradio/TVtechnicianforhelp
Anychangesormodificationsnotexpresslyapprovedbytheparty
responsibleforcompliancecouldvoidtheuser’sauthoritytooperate
theequipment.
Leschangementsoumodificationsnonapprouvésexpressémentparla
partieresponsabledelaconformitépourraitannulerl'autoritéde
l'utilisateuràfairefonctionnerl'équipement.
Industry Canada Notices
ThisdevicecomplieswithIndustryCanadalicence‐exemptRSS
standard(s).Operationissubjecttothefollowingtwoconditions:(1)this
devicemaynotcauseinterference,and(2)thisdevicemustacceptany
interference,includinginterferencethatmaycauseundesiredoperation
ofthedevice.
LeprésentappareilestconformeauxCNRd'IndustrieCanadaapplicables
auxappareilsradioexemptsdelicence.L'exploitationestautoriséeaux
deuxconditionssuivantes:(1)l'appareilnedoitpasproduirede
brouillage,et(2)l'utilisateurdel'appareildoitacceptertoutbrouillage
radioélectriquesubi,mêmesilebrouillageestsusceptibled'en
compromettrelefonctionnement.
Repairstocertifiedequipmentshouldbemadebyanauthorized
Canadianmaintenancefacilitydesignatedbythesupplier.Anyrepairsor
alterationsmadebytheusertothisequipment,orequipment
malfunctions,maygivethetelecommunicationscompanycauseto
requesttheusertodisconnecttheequipment.
Usersshouldensurefortheirownprotectionthattheelectricalground
connectionsofthepowerutility,telephonelinesandinternalmetallic
waterpipesystem,ifpresent,areconnectedtogether.Thisprecaution
maybeparticularlyimportantinruralareas.
WARNING: Usersshouldnotattempttomakesuchconnections
themselves,butshouldcontacttheappropriateelectric
inspectionauthority,orelectrician,asappropriate.
Operating and Storage Temperature
TherecommendedstoragetemperatureforallTouc h Screensis‐10°Cto
60°C(14°Fto140°F).
ForoptimalTouch Screenuse,operationaltemperatureis0°Cto49°C
(32°Fto120°F).
LIMITED WARRANTY
This2GIGTechnologiesproductiswarrantedagainstdefectsinmaterial
andworkmanshipfor1year.Thiswarrantyextendsonlytowholesale
customerswhobuydirectfrom2GIGTechnologiesorthrough2GIG
Technologies’normaldistributionchannels.2GIGTechnologiesdoesnot
warrantthisproducttoconsumers.Consumersshouldinquirefromtheir
installingdealerastothenatureofthedealer’swarranty,ifany.
Therearenoobligationsorliabilitiesonthepartof2GIGTechnologies
forconsequentialdamagesarisingoutoforinconnectionwithuseor
performanceofthisproductorotherindirectdamageswithrespectto
lossofproperty,revenue,orprofit,orcostofremoval,installation,or
reinstallation.Allimpliedwarrantiesforfunctionality,arevalidonlyuntil
thewarrantyexpires.This2GIGTechnologiesWarrantyisinlieuofall
otherwarrantiesexpressedorimplied.
For technical support in the USA and Canada:
855‐2GIG‐TECH(855‐244‐4832)
Email:[e-mail]
Internet:dealer.2gig.com
Visitwebsitefortechnicalsupporthoursofoperation
For technical support outside of the USA and Canada:
Contactyourregionaldistributor
Visitdealer.2gig.comforalistofdistributorsinyourregion.
PN77‐000090‐001Rev.D