LINK-MI LM-TV03-4K2K User manual

LM-TV03-4K2K
4K video wall controller
User Manual

1
Catalog
1.Installation Instructions ……………………………2
2.Product Brief …………………………………………… 3
3.Controller Installed…………………………………… 4
4.Remote Control Settings ………………………………7
5.Pressing Setting………………………………………… 8

2
1thInstallation Instructions
For the safety of you and your equipment, please be sure to read
the safety instructions carefully before using this device.
If you use in the event of doubt, please read this manual first.
Detailed description of the equipment operating in the body. If you
still have questions, please contact us, we will give you a
satisfactory answer as soon as possible.
This specification is subject to version changes, without prior
notice, please understand.
Equipment installation, please note the following:
1.Power supply:
This device uses100-240VAC input voltage,In order for the device to
work properly.
2. Power:
Equipment is required when moving or other jobs that require power,
to turn off all the power, pull the plug, in order to ensure the
safety of you and your equipment.
3. Cable:
Not in power cable, signal lines, communication lines, such as cable,
cables were crushed or squeeze should be avoided to prevent danger of
leakage or short circuit.
4.Signal cable connections:
Plug from the device, pull the signal line, the device need to power
down, so as not to damage the device. Charge plug damage is not
covered under warranty.
5.Openings:
Outer surface of the device may be cooling holes, do not plug the
hole, so as to avoid heat accumulation and damage equipment or cause
a fire risk.
6.Equipment installation:
Reasonable placement of equipment, such as loading standard rack,
chassis, Cabinet, or placed on a solid, flat work surface to prevent
equipment fell.
7.Environment:

3
Equipment working environment, pay attention to dust, moisture,
especially to prevent liquids from soaking and splashed into the
device.
8.Maintenance:
All repair work should be done by professional maintenance personnel
without training do not attempt to repair the device yourself. To
prevent the risk of electric shock, do not open the housing.
2th Product Brief
1.Overview:
LM-TV03-4K2K Series is a high performance UHD Ultra HD 4K Image
splicer, user-customiz able 2To 12 Image stitching. Its main function
is to M × N splicing display unit displays a 3840×2160@60HZ of super
high definition image. Products using advanced image processing
technology, the input signal can support HDMI2.0, that is
3840×2160@60HZ, will not appear, even when playing fast animation
delay, dropped frames are like.
Support 1 HDMI2.0、1 Mobile Signal、1 DP1.2 Enter, Maximum resolution
support 3840×2160@60HZ; HDMI Signal outputs, each output is a fixed
rate 1920×1080@60HZ.
Other more detailed feature descriptions, please refer to the
product specifications.

4
2. 4K and 1080P difference
The same size, higher sharpness
3. Controller pictures

5
3thController Installed
1.Open the package
Check host attachments. Include the host, the power cord, remote
control, warranty card and instructions.
2.Installation machine
2.1.TV sets:
LCD TV or other display device setting input signal to HDMI State.
Display unit has multiple HDMI input ports, make sure that connection
splicer HDMI lines corresponding to the port;
2.2 .Stitching device connected to the TV:
When in place of picture mosaic, by HDMI Line equipment Output
With LCD TV HDMI Input connection, please note that TV must
correspond with the splicing processor is connected to the port.
Output pictures for the following equipment:
Each of the LCD unit with the splicer is connected to the output port,
location boxes indicate LCD, digital output port, each mosaic mode in
the following illustration each LCD is connected with the
corresponding port:

6
2.3.Input signal connections
Product support 1HDMI、1Mobile Signal、1DPInput, all input embedded
audio input or binding, users can access all the signals on demand,
or access part of the signal, interface functions and interface
pictures are as follows:
Mobile Signal: Support HDMI1.4 Signal input, maximum support
3840×2160@30HZ HDMI Signal input can be backwards compatible;
through a Mobile Signal Go HDMI Lines can also be compatible with
Mobile Signal Output image output device, such as Mobile Signal Enabled
mobile phones or Tablet;

7
HDMI: Support HDMI2.0 Signal input, enter the maximum resolution
supported 3840×2160@60HZ;
DP: Support maximum resolution support 3840×2160@60HZ;
2.4.Audio connection
A-OUT Splicer audio output, can purchase an ordinary computer audio
and A-OUT Connections;
2.5.Power on boot
After the above cable connect the power, the power indicator
light, equipment in good working condition;
2.5.180°rotation.
1x2

8
3x1
4thRemote Control Settings
Stitching device and the display unit are attached, connected to
power the red power light is on, the device works, by remote control
or key makes it easy to set up your equipment, or the chassis
configuration.
1. set up the remote control:
1.1. Call menu
Press the remote controlMENUKey, the following pop-up menu;
1.2. Select the submenu
Continuous pressMENUKeys moves the cursor stays in the
different submenu, submenu that stays as red text, press OK Key to
select the menu entries, it becomes green text to the selected menu
function sets the corresponding submenu.

9
1.3. Change the product settings
After menu changes to green, with remote control or keys to
change product parameters or properties, press the return key to
save the setting and exit the menu.
2. signal source selection
LM-TV03-4K2K Signal source menu option: Auto-select,D0: DP、
D1:HDMI、D2:Mobile Signal。
2.1. Automatic selection:
Through the remote control handle menu "signal source" set to
"automatic selection", in the case of equipment had no access to
other sources, you can automatically insert the signal source and the
signal source identification automatically display splicing unit.
2.2. Manual selection:
Can be used for a single source or multiple sources at the same
time connected to the device, by manually switching the signal source
on the remote control display screen displays an image.
3. split mode
Through the submenu you can choose many kinds of stitching
patterns, such as 1x2、2x1、3x1 Mode, typically split mode before
leaving the factory is set up, no need to debug.
4. Board, cardID-Flip
By selecting "cardID"Number, in the menu" flip "setting
theIDWhether an image needs to be rotated,180Degrees.
5. the language
Menu can be selected by remote control:English, Simplified Chinese,
traditional Chinese, three different menu display language.