LINK-MI LM-DT200 User manual

USER MANUAL
LM-DT200
HDMI Fiber Optic Transmission
1.0 Introduction
2.0 Panel Description
3.0 Function Specification
4.0 Connection and operation

1.0Introduction
LM-DT200 is a perfect solution for transmitting HDMI audio and video through the fiber, the
set of device includes a sender of DT200T and a receiver of DT200R. Our products transmit the
HD video over optical fiber, which making the images clearer as well as the transmission more
stable. At the same time, the product has the built-in IR remote control function.
2.0 Panel Description
2.1 Front Panel

HDMI TX
HDMI RX
HDMI PORT
Video Input
Video Output
IR PORT
IR Input
IR Output
Fiber Port SC
Optic-fiber Data Transmission
RESET KEY
Hold down the key for 8 seconds after power on,
the model will restore default settings
2.2 Indicator led.
Indicator led
Status
FX
Light On
The transmission rate is correct
Light Off
The transmission rate is not correct
Link act
Light On
Fiber Link up
Flash
Packets of data are transmitting in the indicating
port
Dpx
Light On
In the State of full-duplex
Light Off
In the State of half-duplex
3.0 Function Specification
> HDMI 1.3/HDCP1.1 & 1.2
> Both Optic-fiber transmission and Ethernet Transmission
> Support point-to-point mode, one point-to-many mode and cascaded transmission mode.
> built-in IR remote control function, you can control the set-top box at the receiving site using the IR
remote control.
> Pure hardware design, just plug and play, no need to install extra software.
Video Parameter
Video Resolution
640X480 @ 60fps 800X600 @ 60fps
1024X600 @ 60fps 1024X768 @ 60fps
1152X864 @ 60fps 1280X600 @ 60fps
1280X720@ 60fps 1280X768@ 60fps
1280X800@ 60fps 1280X960@ 60fps
1280X1024@ 60fps 1440X1050@ 60fps
1440x900 @ 60fps 1600x900 @ 60fps
1660x1200 @ 60fps 1680x1050 @ 60fps
1920x1080 @ 60fps 1920 x1200 @ 60fps
Audio
32kHz, 44.1kHz and 48kHz
Infrared Support
38KHz; NEC code
HDMI Version
HDMI 1.3
HDCP Version
HDCP 1.2

Other Parameters
Power input
AC input: 100V - 240V (50 - 60Hz)
Max Power
Consumption
LM-DT200T: 5W
LM-DT200R: 5W
Size (L-W-H)
110×80×30 mm
Net Weight
456g*2pcs
Operating
Temperature/Humidity
0℃- 70℃/ 10% - 80%RH(no condensation)
Storage
Temperature/Humidity
-10℃- 80℃/ 5% -90% RH(no condensation)
Fiber Parameter
Product
Model
Max
Distanc
e
Fiber
type
Optical
Interface
Wave
Length
Optical
Power
Receiving
Sensitivity
Link
Budget
LM-DT200-S20
10-20KM
single
mode
SC/FC
1310nm
-11~-3dBm
-36dBm
-25dBm
LM-DT200-S40
40KM
single
mode
SC/FC
1510nm
-11~-3dBm
-36dBm
-25dBm
1310nm
-5~0dBm
-36dBm
-31dBm
4.0 Connection and operation
1. Please connect the HDMI signal source to the LM-DT200T。
2. Connect LM-DT200R to the HD displayer.
3. Between LM-DT200T and LM-DT200R (SC port-to-SC port) use optical fiber to
connect.
4. IR remote control function, connect the IR receiver to the HDMI TX and connect
the IR transmitter to the HDMI RX.
5. Power on the device, POWER light on, then it will do the self-checking job with
the other indictors blinking automatically. When the Link light flash, the
device starts up.
Application diagram