Linksys WRT54GL - Wireless-G Broadband Router... Quick start guide

Firmware Upgrade Procedures:
Linksys WRT54GL v1
fw ddwrt_v24_sp1_std_generic_10011
1. General Information
Make: Linksys
Model: WRT54GL
Hardware Version: any
Firmware Version: ddwrt_v24_sp1_std_generic_10011
MAC Address Info:
WLAN MAC: two higher than LAN MAC.
LAN MAC: labeled on the bottom of the device.
WAN MAC: one higher than LAN MAC.
Example: if the LAN MAC printed on the device is 00:11:DE:AD:BE:EF, then
the WAN MAC is 00:11:DE:AD:BE:F0 and the WLAN MAC is
00:11:DE:AD:BE:F1.
Defaults Settings/Configuration:
Default LAN IP Address: 192.168.1.1
Web Interface Username: root
Default Web Interface Password: admin
IMPORTANT: These instructions assume that the device is already running a stock
ddwrt_v24_sp1_std_generic_10011 firmware. Do not upgrade the device to the ddwrt
firmware if it is running the original Linksys manufacturer’s firmware; instead, see the
ddwrt website for instructions on how to convert the device to run the ddwrt firmware
(you must first upgrade to a “mini” ddwrt firmware).
2. Wired Upgrade Procedure
Prerequisites:
•client computer with ethernet interface and firmware file
•ethernet cable
•device LAN IP address (referred to below as <Device_LAN_IP_Address>)
•device web interface password
Limitations: if the device is running a CB firmware, under certain situations you may
need to reference the CB User’s Manual to perform a firmware upgrade.

Firmware Filename: dd-wrt.v24_std_generic_[X].bin (where [X] is an optional
string)
Instructions:
•Connect a wired (ethernet) client with DHCP enabled to a LAN port on the device
with an ethernet cable. If you are not served an IP address by the device, you will
need to determine the device LAN IP address (see next step) and manually assign
the wired client an IP address in the same subnet as the device LAN IP address.
For example, if the device LAN IP address is 192.168.1.1, assign yourself an IP
address of 192.168.1.11.
•Determine the <Device_LAN_IP_Address>. If the device is running DHCP, the
device LAN IP address is likely the default gateway of your connected client;
otherwise, if the device LAN IP address is not the default LAN IP address listed
above, the device LAN IP address can be retrieved in wireless sniffer capture data
(e.g., kismet).
•Log on to the device’s web interface by opening a web browser and pointing it to
http://<Device_LAN_IP_Address>, where “<Device_LAN_IP_Address>” is the
device IP address determined from the previous step (i.e., not the literal string
“<Device_LAN_IP_Address>”). For example, if the <Device_LAN_IP_Address>
is 192.168.1.1, use http://192.168.1.1.
•At the login prompt, enter the web interface password and click OK.
•Then click the “Administration” link on the upper right tab.
•Then click the “Firmware Upgrade” tab.
•Click the “Browse…” button and browse to the dd-wrt.v24_std_generic_[X].bin
firmware file on the client computer.
•Click the “Upgrade” button.
•Watch the interface for any additional steps/error messages/information.
Reboots Automatically After Upgrade: Yes
Approximate Upgrade Time: 130 seconds
Known Issues: None
3. Wireless Upgrade Procedure
Prerequisites:
•client computer with 802.11 wireless client card (or built-in 802.11 client
hardware).
•wireless encryption (WEP, WPA, or WPA2) key (if wireless security is enabled)
•device LAN IP address (referred to below as <Device_LAN_IP_Address>)
•device web interface password
Limitations: None

Firmware Filename: dd-wrt.v24_std_generic_[X].bin (where [X] is an optional string)
Instructions:
•Connect/associate the wireless (802.11) client computer (with DHCP enabled) to
the device. If wireless encryption (WEP, WPA, or WPA2) is enabled on the
device, enter the key when prompted. If you are not served an IP address by the
device, you will need to determine the device LAN IP address (see next step) and
manually assign the wired client an IP address in the same subnet as the device
LAN IP address. For example, if the device LAN IP address is 192.168.1.1,
assign yourself an IP address of 192.168.1.11.
•Determine the <Device_LAN_IP_Address>. If the device is running DHCP, the
device LAN IP address is likely the default gateway of your connected client;
otherwise, if the device LAN IP address is not the default LAN IP address listed
above, the device LAN IP address can be retrieved in wireless sniffer capture data
(e.g., kismet).
•Log on to the device’s web interface by opening a web browser and pointing it to
http://<Device_LAN_IP_Address>, where “<Device_LAN_IP_Address>” is the
device IP address determined from the previous step (i.e., not the literal string
“<Device_LAN_IP_Address>”). For example, if the <Device_LAN_IP_Address>
is 192.168.1.1, use http://192.168.1.1.
•At the login prompt, enter the web interface password and click OK.
•Then click the “Administration” link on the upper right tab.
•Then click the “Firmware Upgrade” tab.
•Click the “Browse…” button and browse to the dd-wrt.v24_std_generic_[X].bin
firmware file on the client computer.
•Click the “Upgrade” button.
•Watch the interface for any additional steps/error messages/information.
Reboots Automatically After Upgrade: Yes
Approximate Upgrade Time: 130 seconds
Known Issues: None