Lippert Components Jack-It User manual

1
Jack-It
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 06.16 - Jack-It Aftermarket Manual
Introduction
The Jack-IT® is a bicycle rack designed to attach to your RV.
Additional information about this product can be obtained from
www.lci1.com/support or by downloading the free myLCI app.
The app is available on iTunes® for iPhone® and iPad® and
also on Google Play™ for Android™ users.
iTunes®, iPhone®, and iPad® are registered trademarks of
Apple Inc. Google Play™ and Android™ are trademarks of
Google Inc
Lippert Components, Inc. recommends that the following
inspections, troubleshooting, component replacement, and
verications be completed only by certied RV technicians.
Safety Requirements
Moving parts can pinch,
crush or cut. Keep clear
and use caution.
Failure to follow the
instructions provided in
this manual may result
in death, serious injury,
vehicle damage, or
voiding of the component
warranty.
Jack-It
Aftermarket
Manual
Table Of Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Tools required 2
Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . 2
Securing Bikes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Patent protected, trademarked, and produced by Let’s Go Aero, Inc
Corporate Ofce: 4474 Barnes Road, Colorado Springs, CO 80917 USA.
Made in China.
US Patent Numbers: 8,899,456, D717,716, D717,717, D684,917, D722,289,
patents pending.

2
Jack-It
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 06.16 - Jack-It Aftermarket Manual
Preparation
Tools required
9/16” Socket Wrench
3/4” Socket Wrench
Installation Instructions
1. Remove the tongue jack from the coupler. Position the
PowerTower ™ (Fig. 1G) on the coupler. Place the jack on
the PowerTower™ (Fig. 1G) and secure both to the coupler
using 3 nuts, bolts and washers each (Fig. 1H, 1I, 1J).
Note: If there is no tongue jack, attach the PowerTower™ (Fig.
1G) to the coupler on the front of the trailer using 3 nuts,
bolts and washers each (Fig. 1H, 1I, 1J).
2. Attach the stinger (Fig. 1F) to the PowerTower™ (Fig. 1G)
using NoMotion™ pin and washers (Fig. 1C, 1D, 1A). For
safety, insert cotter pin (Fig. 1B) through the hole at the end
of the NoMotion™ pin (Fig. 1C) after tightening securely.
3. Attach base (Fig. 1E) to stinger (Fig. 1F) using NoMotion™
pin and washers (Fig. 1C, 1D, 1A). For safety, insert cotter
pin (Fig.1B) through the hole at the end of the NoMotion™
pin (Fig. 1C) after tightening securely.
A
B
C
D
E
F
G
H
I
J
Fig.1
The use of this product
while bicycles are loaded
may affect the turning
radius on some vehicles.
Check the turning radius
before travel.

3
Jack-It
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 06.16 - Jack-It Aftermarket Manual
Fig.2
A
B
C D E
F
G
H
B
B
Securing Bikes
1. For two bicycles, the best technique is to postion the bicycles
front to back / back to front with the chain ring to the outside.
2. Hang one bicycle on the tow vehicle side of the bicycle rack,
so the top of the wheels are each supported by a cradle.
3. Secure by tensioning each rubber strap over the top of each
tire and engaging a strap hole with the end of the cradle.
4. Use the SwayStop™ pin to secure one wheel below the
frame where the wheel crosses the wing using the same
technique with the rubber strap (Fig. 3).
5. Repeat for a second bicycle on the trailer side of the bicycle
rack.
Note: Several hole positions are provided
for cradles (Fig. 2A). Pads (Fig. 2D) and
SwayStop™ pins (Fig. 2F) slide along the
length of wings (Fig. 2G).
4. If not already in place, slide two pads (Fig. 2D)
onto each wing (Fig. 2G).
5. Slide one SwayStop™ pin (Fig. 2F) onto each
wing (Fig. 2G). Attach wings (Fig. 2G) to base
(Fig. 2E) using two snap pins (Fig. 2H).
Note: SwayStop™ pins (Fig. 2F) should point in
opposite directions.
6. Install six rubber straps (Fig. 2B) one onto each
cradle (Fig. 2A) and one onto each SwayStop™
pin (Fig. 2F).
7. Attach four cradles (Fig. 2A). Attach two to each
wing (Fig. 2G) securing with cotter pins (Fig.
2C). Attach one on each wing facing the tow
vehicle and one on each wing facing the trailer.
Note: Adjustment will be necessary depending on
the size and desired position of the bicycles.
Always make sure all connections between the bicycle rack and the trailer
coupler are secure / tight / ready for travel. Always make sure the bicycles
are securely attached to the bicycle rack before you drive away.
Fig.3

4
Jack-It
Aftermarket Manual
www.lippertcomponents.com [phone] Rev: 06.16 - Jack-It Aftermarket Manual
Manual information may be distributed as a complete
document only, unless Lippert Components provides explicit
consent to distribute individual parts.
All manual information is subject to change without notice.
Revised editions will be available for free download at www.
lippertcomponents.com. Manual information is considered
factual until made obsolete by a revised version.
Please recycle all obsolete materials and contact Lippert
Components with concerns or questions.
Notes