LMI Technologies Gocator 1300 User manual

1300
3. STARTING GOCATOR
NOTE: Gocator must be connected to a host computer in order to launch the user interface and set up the sensor.
Gocator sensors are configured by connecting with a web browser. For details on browser compatibility, see the user manual.
TROUBLESHOOTING
PROBLEM SUGGESTED RESOLUTION
Mechanical / Environmental
The sensor is warm. • It is normal for a sensor to be warm when powered on.
Connection
When connecting with a web
browser, the sensor is not found
(page does not load).
• Verify the sensor power is on. This will be indicated by an illuminated POWER LED.
• Verify the Power & Ethernet cordset is connected to the Power/LAN connector and the Ethernet RJ45 plug is connected to the Ethernet switch.
• Verify that the client computer’s network settings are properly configured.
See Getting Started > Network Setup in the Gocator user manual or your computer’s documentation on configuring a network adapter.
• Download 14405-x.x.x.x_SOFTWARE_GO_Tools.zip from the downloads area of LMI’s website at www.lmi3D.com.
Unzip and run the Sensor Discovery Tool [Discovery>kDiscovery.exe] to verify that the sensor has the correct network settings.
When attempting to log in, the
password is not accepted.
• Download 14405-x.x.x.x_SOFTWARE_GO_Tools.zip from from the downloads area of LMI’s website at www.lmi3D.com.
Unzip and run the Sensor Discovery Tool [Discovery>kDiscovery.exe] to find the sensor on the network and click Factory Restore.
WARNING: Performing a factory restore resets your configuration settings to their original values. These settings can be recovered from backup files if you
have previously saved them.
Laser Profiling
When the Play button is pressed,
the sensor does not emit laser light.
• Ensure that the decal covering the laser emitter window, normally axed to new sensors, has been removed.
• Verify that the LASER LED on the Gocator is illuminated. If not, the laser safety input signal is o.
To determine the correct solution for your application, see Specifications > Gocator Power/LAN Connector > Laser Safety Input in the user manual.
• The exposure setting may be too low. For more information, see Gocator Web Interface > Scan Setup and Alignment > Sensor > Exposure in the user manual.
The sensor emits laser light, but the
Range Indicator does not illuminate
and/or points are not displayed in
the data viewer.
• Verify that the measurement target is within the sensor’s field of view and measurement range.
The RANGE LED on the Gocator will illuminate when the target is in range.
• Check that the exposure time is set to a reasonable level.
For more information, see Gocator Web Interface > Scan Setup and Alignment > Sensor > Exposure in the user manual.
The sensor CPU level is near 100%.
• Review the active measurements and remove any that are unnecessary.
• Consider reducing the trigger speed.
• Consider reducing the laser profiling resolution.
An example of the user interface in use
Quick Start Guide
For the user manual, CAD drawings, firmware release notes, SDK,
and more, go to www.lmi3D.com/support/downloads.
15186-01.13_MANUAL_Quickstart_Gocator-1x00-Series-Side-Mount-Package
©2018 LMI Technologies Inc. All rights reserved.
SIDE MOUNT PACKAGE
Americas LMI Technologies (Head Oce)
Vancouver, Canada
[phone]
EMEAR LMI Technologies GmbH
Berlin, Germany
[phone]
Asia Pacific LMI (Shanghai) Trading Co., Ltd.
Shanghai, China
[phone]
LMI Technologies has sales oces and distributors
worldwide. All contact information is listed at lmi3D.com/
contact/locations.
In Windows 7
a. Open the Control Panel > Network and Sharing Center > Change
Adapter Settings.
b. Right-click desired network connection, and then click Properties.
c. On the Networking tab, click Internet Protocol Version 4 (TCP/IPv4),
and then click Properties.
d. Select “Use the following IP address” option.
e. Enter IP Address “192.168.1.5” and Subnet Mask “255.255.255.0”, then
click OK.
In Mac OS X 10.6
a. Open the Network Pane in System Preferences and select Ethernet.
b. Set Configure to “Manually”.
c. Enter IP Address “192.168.1.5” and Subnet Mask “255.255.255.0”, and
then click Apply.
B. RUNNING GOCATORA. LAUNCHING THE INTERFACE
Open a web browser and enter the sensor address.
Step 2
Step 1
Gocator is shipped with the following default network
configuration:
Setting Default
DCHP Disabled
IP Address 192.168.1.10
Subnet Mask 255.255.255.0
Gateway 0.0.0.0
Change network setting on host computer.
Step 1
Select the Manage page.
Step 2
Ensure that Replay mode is o (slider set to left) and that the
Laser Safety switch is enabled or the Laser Safety input is
high. Press the Start button in the toolbar to start the sensor
(a laser line should now be visible).
Step 3
Move target into the laser plane and measure!
RECORD SNAPSHOT STA RT
REPLAY (off)
Gocator sensors can also interface directly with HexSight.
Refer to the HexSight Quick Start Guide for more information.
NOTE
The Gocator interface loads.

Mount the sensor using four M6 x 1.0 screws of suitable length.
The recommended thread engagement into the housing is 8 - 10 mm.
Do not occlude camera’s view of the laser Do not install near surfaces that might
create unanticipated laser reflections
2. CONNECTING GOCATOR TO A HOST COMPUTER
1. MOUNTING
Standalone System
“MAIN” GOCATOR
Serial / Analog / Digital outputs
“BUDDY” GOCATOR
GOCATOR I/O
CORDSET
GIGABIT ETHERNET
SWITCH
Power, Laser Safety, Trigger inputs,
and Encoder
MASTER 2400
GOCATOR POWER and
ETHERNET CORDSET
Dual / Multi-Sensor System
GOCATOR OVERVIEW
There are several sensor models in the Gocator 1300 series, each
designed with a unique Clearance Distance (CD), Measurement
Range (MR) and Field of View (FOV). Refer to the user manual
for more information about your model.
GROUNDING GOCATOR
Gocator housings should be grounded to the earth and the
grounding shield of the Gocator I/O cordsets. Gocator
sensors have been designed to provide adequate grounding
through the use of M6 x 1.0 screws. Always check grounding
with a multi-meter to ensure electrical continuity between the
mounting frame and the Gocator connectors.
The frame or electrical cabinet that the Gocator is mounted to
must be connected to earth ground.
ELECTRICAL SAFETY
Minimize voltage potential between system ground (ground
reference for I/O signals) and sensor ground
Use shielded cables with shield grounded at both ends.
Sensor housing should be connected to earth ground.
Use a suitable power supply
The +24-48V power supply used with Gocator 1300 sensors
should be an isolated supply with inrush current protection.
Use care when handling powered devices
Wires connecting to the sensor should not be handled while
the sensor is powered. Doing so may cause electrical shock to
the user or damage to the equipment.
NOTE: Mounting the Gocator is recommended before applying power. Ensure that a proper earth ground is
established and that a heat sink is properly installed before applying power.
LASER SAFETY
The full laser safety details including precautions,
responsibilities and requirements are stated in the Gocator
user manual. Use of controls or adjustments or performing
procedures other than those specified in the user manual may
result in hazardous radiation exposure.
Laser
Laser
Sensor
WARNING: DO NOT LOOK DIRECTLY
INTO THE LASER BEAM
The light emitted from these devices has been set in
accordance with IEC60825. However, staring into the beam,
whether directly or indirectly, must be avoided. IEC60825
classifies laser products into three dierent categories
depending on light emitted, wavelength and eye safety.
This product is designated for use solely as a component
and as such it does not fully comply with the standards
relating to laser products specified in U.S. FDA CFR Title 21
part 1040 and
IEC 60825-1.
Connector Pin Details
Camera
Laser
Emitter Power/
LAN
I/O
Connector
Mounting
Holes
M6X1.0 10
LED Indicators
When starting the Gocator,
the Power indicator and the
Laser (if safety is enabled)
should be illuminated. If
they are not, refer to the
troubleshooting table below
or the user manual.
GOCATOR I/O
CORDSET
GOCATOR POWER and
ETHERNET CORDSET
USER PC
(can be disconnected after setup)
Power: 24-48VDC @ 13W
Laser Safety: +24-48VDC to enable
Wire rich I/O
as required by application
ex. Serial / Analog / Trigger Input,
Encoder / Photocell / etc.
GOCATOR
GROUNDING CORDSET (RECOMMENDED)
To minimize interference with other equipment, the Power
& Ethernet or the Power & Ethernet to Master cordset
(depending on cordset used in system) can be grounded
by terminating the cordset shield before the split. The most
eective grounding method is to use a 360-degree clamp.
For instructions, see the user manual.
I C
B
N
M
A
K
U
L
T
RP
O
D
E
F
S
G
H
C
J
TN
L
M
A
U
P
R
S
G
O
E
Gocator Power/LAN (to standalone and to Master)
Gocator I/O
Pin Function Conductor Color
LGND_24-48V White/Orange & Black
LGND_24-48V Orange/Black
ADC_24-48V White/Green & Black
ADC_24-48V Green/Black
GSafety- White/Blue & Black
JSafety+ Blue/Black
ESync+ White/Brown & Black
C Sync- Brown/Black
M Ethernet MX1+ White/Orange
N Ethernet MX1- Orange
O Ethernet MX2+ White/Green
P Ethernet MX2- Green
S Ethernet MX3- White/Blue
REthernet MX3+ Blue
T Ethernet MX4+ White/Brown
U Ethernet MX4- Brown
Pin Function Conductor Color
D Trigger_in+ Grey
H Trigger_in- Pink
N Out_1+ (Digital Output 0) Red
O Out_1- (Digital Output 0) Blue
S Out_2+ (Digital Output 1) Ta n
T Out_2- (Digital Output 1) Orange
M Encoder_A+ White/Brown & Black
U Encoder_A- Brown / Black
I Encoder_B+ Black
K Encoder_B- Violet
A Encoder_Z+ White/Green & Black
L Encoder_Z- Green / Black
B Serial_out+ White
C Serial_out- Brown
E Serial_out2+ Blue / Black
G Serial_out2- White / Blue & Black
P Analog_out+ Green
F Analog_out- Yellow & Maroon/White
R Reserved Maroon
View: Looking into the connector on the sensor.
View: Looking into the connector on the sensor.
Always power down sensor
before removing cables
from the sensor
Leave protective caps on any
connectors that are not used.
Failure to adhere to the guidelines described
in this section may result in electrical shock
or equipment damage.
CLASS 2M LASER PRODUCT
LASER RADIATION
DO NOT STARE INTO THE BEAM OR VIEW
DIRECTLY WITH OPTICAL INSTRUMENTS
OR MAGNIFIERS
CLASS 3R LASER PRODUCT
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 3B LASER PRODUCT
LASER RADIATION
AVOID EXPOSURE TO THE BEAM