Locinox Turnitec User manual

TURNITEC
NEDERLANDS
USER GUIDE ENGLISH
DEUTSCH
FRANCAIS

• As manufacturer of this product, we guarantee that we have
taken all the necessary steps in order for this product to comply
with the current safety requirements.
Copyright
Copyright © 2009 Locinox. All rights reserved.
This product incorporates copyright protected technology that is protected by a number of EU
patent method claims and other intellectual property rights owned by the Locinox Corporation
and other rightholders.
Use of this copyright protected technology must be authorized by the Locinox Corporation.
Reverse engineering or disassembly is prohibited. No part of this publication can either
be reproduced, communicated, transcribed, stored in a retrieval system or be translated
into any language in any form or by any means, whether electronic, mechanical, magnetic,
optical, chemical, manual or otherwise, unless explicit written consent has been given by the
copyright holder.
Notice
The contents of this publication is subject to change. The company reserves the right to alter the
contents of this publication at any time and without notice. The contents of this publication may
contain inaccuracies or typographical errors and is supplied forinformational use only.
Technical Support
If you require any additional information or assistance during the installation, please contact your
dealer, who will be able to provide the latest information. Alternatively, you can visit the Locinox
website for more technical information or e-mail us on [email protected]

Index - English
1. Introduction 4
2. Package contents 4
3. Optional Turnitec modules 5
4. Preparing the base module 6
5. Installing optional accesscontrol modules 7
6. Installing a clockwise module 8
7. Installing and connecting an electrical control unit 10
8. Installing a counterclockwise module 11
9. Installing and connecting an electrical control unit 13
10. Installing and connecting a TT-COUNTER-LIGHT module on dinrail 13
11. Installing a damping module 14
12. Closing the base mechanism 15
13. Welding the spline axis 17
14. Welding the baseplate 18
15. Fixation & drilling pattern 19
16. Mounting the mechanism 20
17. Electrical wiring 21
18. Mechanical override of the control modules 22
19. Adjusting damping action 22
20. Screw the cover back in place 23

ENGLISH
4
160
526
346
M20 x 1,5
M16 x 1,5
DIN ISO 14
28 x 34
325
A
B
C
F
E
D
Manual - English
1. Introduction
Thank you for choosing our Locinox Turnitec mechanism. Please read the following instructions
thoroughly before installing the mechanism on your turnstile. Enclosed you will find all relevant
user information concerning the Turnitec & optional control modules.
2. Package contents
Please check if your package contains the following items:
ACover
BBase mechanism
CCylinder keys
DSpline Axis
EFixation bolts & nuts
FElectrical coupling nuts

ENGLISH
5
Turnitec & Controlmodule 5
3. Optional Turnitec modules
The Locinox (electro)mechanical control unit allows you to easily create a maintenance free and
high quality turnstile. You now have an (electro)mechanical unit at your disposal with which you
can match the design of your turnstile to the design of your gates!
TT-M34
Mechanical
module
TT-FO3
Fail-open
electromodule
3-arm
TT-FC3
Fail-close
electromodule
3-arm
TT-DM3
Hydraulic
damper
TT-COUNTER-LIGHT
Turnitec counter & passing lights module
TT-BSP or TT-SSP
Welding plate in
stainless steel or
black steel

ENGLISH
6
6 x
4. Preparing the base module
• Screw the included coupling nuts in the base mechanism
• 1 x M16x1,5 cap
• 1 x M20x1,5 cap
• 2 x M16x1,5 coupling nut
• 2 x M20x1,5 coupling nut

ENGLISH
7
Turnitec & Controlmodule
X
X = Min. 115 mm
5. Installing optional accesscontrol modules
• Loosen the cover with a screwdriver, and open it
• Loosen the top chassis bolts, and remove them

ENGLISH
8
AB*
C
• Remove the spacing tubes: The base mechanism is now ready for optional modules
6. Installing a clockwise module
• If no clockwise module is needed, go to step 8 (Installing a counterclockwise module)
• Loosen the fixation bolt and slide the module over the axis
*ATTENTION - STEP B:
Installing the reed contact: only applies when a TT-COUNTER-LIGHT is needed. If you do not
install a TT-COUNTER-LIGHT module then please go to step C.

ENGLISH
9
Turnitec & Controlmodule
• Make sure not to squeeze the cable (only with the electromechanical module) !
• Secure the clockwise module

ENGLISH
10
7. Installing and connecting an electrical control unit
• Applies only for the TT-FO3 and TT-FC3. If no electrical control unit is needed go to step 8:
Installing a counterclockwise module.
• Install the control unit on the dinrail.
• Connect the clockwise module with the control unit.

ENGLISH
11
Turnitec & Controlmodule
• Plug in the cable and make sure to tighten all six screws. Make sure the numbers on the control
unit correspond to the numbers on the connector.
8. Installing a counterclockwise module
• If no counterclockwise module is needed, go to step 11: Installing the damper.
• Loosen the fixation bolt
• execute this step only if you need a TT-COUNTER-LIGHT module. If not then skip to the next step.

ENGLISH
12
• Slide the counterclockwise module over the axis.
• Tighten the fixation bolt of the counterclockwise module

ENGLISH
13
Turnitec & Controlmodule
A
9. Installing and connecting an electrical control unit
• Applies only for the TT-FO3 and TT-FC3. If no electrical control unit is needed go to step 11:
Installing the damper.
• Installation of the unit on DIN rail.
• Connect the clockwise module with the electrical control unit & tighten the screws
10. Installing and connecting a TT-COUNTER-LIGHT module on dinrail
*Electrical wiring : page 21

ENGLISH
14
11. Installing a damping module
• If no damping module is needed, go to step 12 (Closing the base mechanism)
• Slide the damping module over both axes
• Pay attention to the position marks on the gear wheels

ENGLISH
15
Turnitec & Controlmodule
• Damping module situations (No spacing tubes needed)
12. Closing the base mechanism
• Make sure to put the spacing tubes back in place if no damping module is installed

ENGLISH
16
• Check the concentricity between the bearing and the blocking disk (Due to spring tension, the
allignment of these 2 components can differ)
• Be sure the top chassis is mounted correctly before screwing it down.

ENGLISH
17
Turnitec & Controlmodule
13. Welding the spline axis
• Alignment of the spline axis regarding the rotor

ENGLISH
18
X = Max. 140 mm en Min. 65 mm
X
• Length of the spline axis above the welding plate
14. Welding the baseplate
• If you choose not to use a Locinox welding baseplate (TT-BSP or TT-SSP). Go to step 15

ENGLISH
19
Turnitec & Controlmodule
97
87 87
25,4 ±0,1
37,8 ±0,1
Ø36
152,5377,5
175 175
72,5 72,5
355 130
84 84
8,2
+ 0,2
0
75
154 154
• The oval holes need to be directed to the passenger side.
• Align the base steel plate with respect to the rotor (Long side parallel to the rotor arm)
15. Fixation & drilling pattern
• Prepare your own turnstyle baseplate for the Locinox Turnitec mechanism TT-BM3.
• Fixation and drilling pattern when not working with the TT-BSP or TT-SSP.

ENGLISH
20
A
16. Mounting the mechanism
• Slide the mechanism over the spline axis
• Attach the mechanism to the welding plate