Lockton SBML23 Assembly instructions

4.5mm DIAMETER HOLE
8.0mm COUNTERSINK 90°
25.5mm
mm5.5
mm761
mm651
20mm
mm41mm09
mm73
23mm
BACKSET
mm5.5
mm5.72
19mm
DIAMETER
2 HOLES 8mm
DIAMETER
mm5.5
mm5.72
mm951
mm09
mm73
23mm
BACKSET
20mm
TURN/
CYLINDER
2 HOLES 8.0
DIAMETER
19mm
DIAMETER
23mm BACKSET 23mm BACKSET
27.5mm
27.5mm
25.5mm
DRILL HOLE
20mm DIA.
FOR OVAL
CYLINDER
DRILL HOLE
20mm DIA.
FOR TURN
KNOB ONLY
DRILL HOLE
20mm DIA.
FOR OVAL
CYLINDER
DRILL HOLE
20mm DIA.
FOR TURN
KNOB ONLY
DRILL HOLE
19mm DIA.
DRILL HOLE
19mm DIA.
DRILL HOLE
10mm DIA.
DRILL HOLE
10mm DIA.
156mm
FOLD ALONG DOTTED LINE AND ALIGN TEMPLATE WITH EDGE OF DOOR FOR 23mm BACKSET
FOLD ALONG DOTTED LINE AND ALIGN TEMPLATE WITH EDGE OF DOOR FOR 23mm BACKSET
DO NOT DRILL HOLES RIGHT
THROUGH DOOR TO PREVENT
POSSIBLE DAMAGE DOOR
SIEPER Group
Tel: [phone]
E-mail: [e-mail]
www.sglocks.com.au
INSTALLATION SHEET: LOCKTON SBML23 MORTICE LOCK
DOOR PREPARATION
HANDING OF DOOR - ENGLISH STANDARDS
RIGHT HAND DOOR LEFT HAND DOOR
OUTSIDE
DOOR OPENING
IN
OUTSIDE
DOOR OPENING
OUT
OUTSIDE
DOOR OPENING
IN
OUTSIDE
DOOR OPENING
OUT
PLEASE READ BEFORE INSTALLATION:
-Before drilling holes in the door, ensure correct
handing of lock is being installed.
-Warranty may be void is case of lock has been
opened. Lock function changes can be made
without opening the lock case.
METAL DOOR - LOCK INSTALLATION
1. Determine the height & position of the lockset on the door
2. Use template and mark faceplate cut out
3. Cut face plate window: 156mm x 25.5mm with 3mm radius corners
4. Place template supplied in face plate opening and drill 4.5mm holes, countersink holes with 8mm
diameter at 90°
5. Use template supplied to mark appropriate holes for selected LOCKTON mortice lock
furniture.
DOOR TEMPLATE

LOCK PREPARATION LOCK INSTALLATION
FINISHING INSTALLATION
Both Sides
Lockable
(Warning!) Not for
Escape doors.)
This Side
Locking
(L.H. Door)
Other Side
Locking
(R.H. Door)
Rotate
Anti-Clockwise
Only
Locking Status
Locking bar must be
UP (unlocked) to change
CHECK THE LOCK STATUS
Remove plastic cap from lock cylinder hole. Ensure that the locking bar is
in the unlocked position (UP) If the locking bar is NOT in the (UP) position
Lift the locking bar (UP) using a small flat blade screw driver.
CHANGING THE LOCK FUNCTIONS:
Depending on the locking function required it can be set to any vestibule
or combination lock status using a small flat blade screw driver. rotate the
locking slot (Anti-Clockwise Only) to the required location.
See Lock Status Label on Lock Body for more details.
REVERSE LATCH
Determine the handing of the lock using
the door handing chart supplied.
TO CHANGE THE LATCH POSITION:
Remove the face plate, pull and rotate
the latch 180˚ & re-fit face plate.
TURN SNIB ADAPTOR INSTALLATION
LOCKTON Turn Snib Adaptors are captive adaptors and must be installed
correctly for proper lock installation.
1. Determine handing for adaptor
2. Put lock into LOCKED STATUS by moving locking bar into the down
position using a small flat blade screw driver.
3. Insert adaptor See image (A) ensuring the cam arm is positioned in the
locking bar.
4. Insert cylinder / adaptor retaining pin and test operation, ensuring the
locking bar is operating up & down with operation of cam
(Maximum 1/4 turn Left or Right).
5. position locking bar up, UNLOCKED STATUS, until installed in the door.
A
FIT LOCK
Install Lock into door and secure
with the 2 screws provided
LOCKS WITH CYLINDERS
1. Using a small flat blade screwdriver,
remove plastic Cylinder Hole Plug where
lock cylinder will be used.
2. Insert lock into door and secure with 2
screws provided.
3. Secure cylinder with Retainer pin,
ensuring pin is flush with front face of lock
4. Install face plate and secure with 2
screws provided
LOCKS WITHOUT CYLINDERS
Install face plate and secure with 2 screws provided
LOCKS WITH TURNKNOB
Mark and cut the connecting bar as shown Turnknob to be in the vertical
position when unlocked
TURNKNOB
5mm
LOCKS WITH SPINDLE
Insert spindle/s into lock as required, ensuring the spindle spring is
attached to the rear of spindle before assembling
FIT FURNITURE
Rotate handle to correct handing
before installation. Furniture screws
(For Door widths less than 44mm)
Cut the furniture screws 5mm past
the door face when inserted into the
internal furniture
5mm
FIT MOUNTING STRIKE
Prepare door jamb cut out &
fit Strike-Box to frame
Fit Strike to Strike-Box &
secure with 2 screws.
mm68
mm07
mm83
mm12
28.5mm
4.5mmØ & C/Sink
8mm Ø x 90°
To suit lock assembly
Both Sides
Lockable
(Warning!) Not for
Escape doors.)
This Side
Locking
(L.H. Door)
Other Side
Locking
(R.H. Door)
Rotate
Anti-Clockwise
Only
Locking Status
Locking bar must be
UP (unlocked) to change
INSTALLATION SHEET: LOCKTON SBML23 MORTICE LOCK