Logia LOWSC510SWB User manual

5-IN-1 WIRELESS
WEATHER STATION
WITH WI-FI® AND
SOLAR PANEL
USER GUIDE
LOWSC510SWB
™

2
Thank you for purchasing the Logia™5-in-1 Wireless Weather Station with Wi-Fi® and Solar
Panel. This User Guide is intended to provide you with guidelines to ensure that operation of this
product is safe and does not pose risk to the user. Any use that does not conform to the guidelines
described in this User Guide may void the limited warranty.
Please read all directions before using the product and retain this guide for reference. This product is
intended for household use only. It is not intended for commercial use.
This product is covered by a limited one-year warranty. Coverage is subject to limits and exclusions.
See warranty for details.
SAFETY PRECAUTIONS
PRODUCT FEATURES
PACKAGE CONTENTS
PRODUCT OVERVIEW
LCD DISPLAY OVERVIEW
WIRELESS 5-IN-1 OUTDOOR SENSOR OVERVIEW
INSTALLATION INSTRUCTIONS
SETTING UP THE WIRELESS 5-IN-1 OUTDOOR SENSOR
SETTING UP THE WEATHER CONSOLE
SETTING UP WI-FI®CONNECTION
CREATE AND SYNC YOUR WEATHER SERVER ACCOUNT
UPDATING THE FIRMWARE
OPERATING INSTRUCTIONS
TEMPERATURE
WIND
WEATHER
PRESSURE
RAIN
MAX/MIN
HISTORY
CARE AND MAINTENANCE
TROUBLESHOOTING
SPECIFICATIONS
LIMITED WARRANTY TO ORIGINAL CONSUMER
3
4
5
6
7
8
9
10
12
14
18
21
22
24
26
28
29
30
30
31
33
34
35
38
TABLE OF CONTENTS

3
SAFETY PRECAUTIONS
WARNING! Please read and understand all safety precautions, operating instructions, and
care/maintenance instructions before operating this appliance. Keep this manual for future
reference.
• This product is not a toy. Keep out of the reach of children.
• This product is not to be used for medical purposes or for public information.
• Do not clean the unit with abrasive or corrosive materials.
• Do not place the appliance near open ames or heat sources. Fire, electric shock, product damage,
or injury might occur.
• Only use fresh batteries in the product. Do not mix new and old batteries together.
• Do not disassemble, alter, or modify the product.
• Only use attachments or accessories specied by the manufacturer with this product.
• Do not submerge the display console in water. Dry the product with a soft cloth if liquid spills on it.
• Do not subject the unit to excessive force, shock, dust, extreme temperature, or humidity.
• Do not cover or block the ventilation holes with any object.
• The console of this product is intended to be used indoors only.
• This product is only suitable for a mounting height that is less than 6.6 ft. (2 m).
• Do not tamper with the unit’s internal components. Tampering with the product will void the warranty.
• The indoor sensor of this product should not be placed in direct sunlight, rain, snow, or other
weather conditions.
QUESTIONS OR PROBLEMS? CONTACT US!
Email: [email protected] or call: 1-833-815-0568
www.logiaweatherstation.com

4
PRODUCT FEATURES
1. Wireless 5-in-1 weather sensor measures wind speed, wind direction, rainfall, temperature, and
humidity.
2. No calibration needed! The product is fully pre-calibrated and mostly assembled; all you need to do
is install it and sync with the included display console.
3. Provides precise weather and environmental information right in your own backyard.
4. Color LCD display automatically dims to match room lighting.
5. Alerts you to excessively high/low indoor or outdoor temperatures or humidity, high wind speeds,
extreme changes in barometric pressure, high heat indexes, low wind chills, and more.
6. Syncs with installed Wi-Fi®and online weather servers (Weather Underground and Weathercloud)
to help you store and track weather data in your area.

5
PACKAGE CONTENTS
1. Display console
2. Console power cord
3. Wireless 5-in-1
outdoor sensor
4. Mounting clamp with
two (2) screws
5. Two (2) rubber pads
6. User guide
Features:
• Wireless outdoor weather sensor measure:
-Wind speed
-Wind direction
-Rainfall data
-UV
-Light intensity
-Temperature
-Humidity
• Wireless indoor weather sensor measure:
-Temperature
-Humidity
• Longer battery life with built-in solar panel
• Fully pre-calibrated
• Easy assembly & installation
QUESTIONS OR PROBLEMS? CONTACT US!
Email: [email protected] or call: 1-833-815-0568
LOGIA is a trademark of C&A IP Holdings, LLC in the US, Canada, China and the EU.
Android and Google Play is a trademarks of Google LLC.
Apple, IOS, and App Store are trademarks of Apple Inc. in the U.S. and other countries.
Microsoft, Windows, Windows Server, Windows Vista, and Windows 10 are trademarks of
Microsoft Corporation in the U.S. and/or other countries.
Wi-Fi, WPA, and WPA2 are trademarks of Wi-Fi Alliance in the U.S. and/or other countries.
All other products, brand names, company names, and logos are trademarks of their respective
owners, used merely to identify their respective products, and are not meant to connote any
sponsorship, endorsement, or approval.
Distributed by C&A Marketing, Inc., 114 Tived Lane East, Edison, NJ 08837. Made in China.
© 2020. C&A IP Holdings, LLC. All Rights Reserved.
DISPLAY CONSOLE SPECIFICATIONS
Dimensions: (W x H x D): 8.5″ x 6.9″ x 1″ (215 x 176.5 x 25.5 mm)
Weight: 1.1 lb. (503 g) (with batteries)
Power source: DC 5 V, 1A adapter
Backup battery: CR2032, 3 V battery
Operating temperature range: 23°F ~ 122°F (-5°C ~ 50°C)
WIRELESS 7-IN-1 OUTDOOR SENSOR SPECIFICATIONS
Dimensions (W x H x D): 12.7″ x 11.7″ x 8.5″ (322 x 296 x 217 mm)
Weight: 1.5 lb. (674 g) (with batteries)
Main power: 3 x AA 1.5 V batteries
WIRELESS INDOOR THERMO-HYGRO SENSOR SPECIFICATIONS
Dimensions (W x H x D): 2.4″ x 4.4″ x 1.6″ (60 x 113 x 39.5 mm)
Weight: 0.3 lb. (144 g) (with batteries)
Main power: 2 x AA 1.5 V batteries
WIRELESS SENSOR COMMUNICATION SPECIFICATIONS
Supported sensors: 1 Wireless 7-in-1 weather outdoor sensor
and up to 7 optional wireless thermo-hygro indoor sensors
RF frequency: 915 MHz (US version)
RF transmission range: 492 ft. (150 m)
SPECIFICATIONS
SKU # LOWSC710SWB
8 43812 14387 5
• Precise weather & environmental information
• 12 ~ 24-hour weather forecasting
• Color LCD display screen with dimmable backlight
• Alerts for:
-High/low temperature (indoor/outdoor)
-High/low humidity (indoor/outdoor)
-High wind speeds
-Extreme barometric pressure drop
-High heat index
-Low wind chill
-High/low dew point
• Syncs via Wi-Fi®to online weather servers
• Compatible with Weather Underground and
Weathercloud data servers
• Weather console
• Wireless indoor thermo-hygro sensor
• Wireless 7-in-1 outdoor sensor
• Mounting clamp with two screws
• Rubber pads for mounting clamp
• Console power cord
• Console battery
• User guide
PACKAGE CONTENTS
Wi-Fi®COMMUNICATION SPECIFICATIONS
Wi-Fi®standard: 802.11 b/g/n
Wi-Fi®operating frequency: 2.4 GHz
Router security type: WPA/WPA2, OPEN, WEP
(WEP will only support a hexadecimal password)
Supported devices for setup UI: Smart devices, tablets,
laptops, or PCs with built-in Wi-Fi®and AP mode functionality
such as: Android™ phone or tablet, iPhone or iPad, or a
Windows®laptop/PC
Recommended web browser version: Latest version of
any web browser that supports HTML 5
2AD2W-LOWSC710SWBI
C&A Marketing Inc.
Model No.:LOWSC710SWB
7-IN-1 WIRELESS
WEATHER STATION
WITH Wi-Fi® AND
SOLAR PANEL
TM
7-IN-1 WIRELESS
WEATHER STATION
WITH Wi-Fi® AND
SOLAR PANEL
TM
7-IN-1 WIRELESS
WEATHER STATION
WITH Wi-Fi® AND
SOLAR PANEL
TM
7-IN-1 WIRELESS
WEATHER STATION
WITH Wi-Fi® AND
SOLAR PANEL
TM
7-IN-1 WIRELESS
WEATHER STATION
WITH Wi-Fi® AND
SOLAR PANEL
TM
LOWSC710SWB
350mm
185 mm
1215 mm
698mm
390 mm
1
4
5
6
2
3
Features:
• Wireless outdoor weather sensor measure:
-Wind speed
-Wind direction
-Rainfall data
-Temperature
-Humidity
• Longer battery life with built-in solar panel
• Fully pre-calibrated
• Easy assembly & installation
• Precise weather & environmental information
• 12 ~ 24-hour weather forecasting
• Color LCD display screen with automatic dimming
QUESTIONS OR PROBLEMS? CONTACT US!
Email: [email protected] or call: 1-833-815-0568
LOGIA is a trademark of C&A IP Holdings, LLC in the US, Canada, China and the EU.
Android and Google Play is a trademarks of Google LLC.
Apple, IOS, and App Store are trademarks of Apple Inc. in the U.S. and other countries.
Microsoft, Windows, Windows Server, Windows Vista, and Windows 10 are trademarks of
Microsoft Corporation in the U.S. and/or other countries.
Wi-Fi, WPA, and WPA2 are trademarks of Wi-Fi Alliance in the U.S. and/or other countries.
All other products, brand names, company names, and logos are trademarks of their respective
owners, used merely to identify their respective products, and are not meant to connote any
sponsorship, endorsement, or approval.
Distributed by C&A Marketing, Inc., 114 Tived Lane East, Edison, NJ 08837. Made in China.
© 2020. C&A IP Holdings, LLC. All Rights Reserved.
DISPLAY CONSOLE SPECIFICATIONS
Dimensions: (W x H x D): 4.6” x 7.6” x 0.8” (118 x 192.5 x 21 mm)
Weight: 0.6 lbs. (265 g) (with batteries)
Power source: DC 5 V, 1A adapter
Backup battery: CR2032, 3 V battery
Operating temperature range: 23°F ~ 122°F (-5°C ~ 50°C)
WIRELESS 5-IN-1 OUTDOOR SENSOR SPECIFICATIONS
Dimensions: (W x H x D): 12.7″ x 11.7″ x 8.5″ (322 x 296 x 217 mm)
Weight: 1.5 lb. (674 g) (with batteries)
Main power: 3 x AA 1.5 V batteries
WIRELESS SENSOR COMMUNICATION SPECIFICATIONS
Supported sensors: 1 wireless 5-in-1 weather outdoor sensor
and up to 7 optional wireless hygro-thermo indoor sensors
RF frequency: 915 MHz (US version)
RF transmission range: 492 ft. (150 m)
SPECIFICATIONS
SKU # LOWSCB510SWB
• Alerts for:
-High/low temperature (indoor/outdoor)
-High/low humidity (indoor/outdoor)
-High wind speeds
-Extreme barometric pressure conditions
-High heat index
-Low wind chill
-High/low dew point
• Syncs via Wi-Fi®to online weather servers
• Compatible with Weather Underground and
Weathercloud data servers
• Weather console
• Console power cord
• Wireless 5-in-1 outdoor sensor
• Mounting clamp
• Screws (x2)
• Rubber pads (x2)
• User guide
PACKAGE CONTENTS
Wi-Fi®COMMUNICATION SPECIFICATIONS
Wi-Fi®standard: 802.11 b/g/n
Wi-Fi®operating frequency: 2.4 GHz
Supported router security type: WPA/WPA2, OPEN, WEP
Supported devices for setup UI: Built-in Wi-Fi®with AP
mode function smart devices or laptops e.g.: Android smart
phone, Android tablet, iPhone, iPad, or PC/Mac computer
Recommended web browser: Latest version of any web
browser that supports HTML 5
5-IN-1 WIRELESS
WEATHER STATION
WITH WI-FI® AND
SOLAR PANEL
TM
5-IN-1 WIRELESS
WEATHER STATION
WITH WI-FI® AND
SOLAR PANEL
TM
5-IN-1 WIRELESS
WEATHER STATION
WITH WI-FI® AND
SOLAR PANEL
TM
5-IN-1 WIRELESS
WEATHER STATION
WITH WI-FI® AND
SOLAR PANEL
TM
5-IN-1 WIRELESS
WEATHER STATION
WITH WI-FI® AND
SOLAR PANEL
TM
LOWSC510SWB
8 43812 14880 1
2AD2W-LOWSC510SWBI
C&A Marketing Inc.
Model No.:LOWSC510SWB
Box Size : 390 x 350 x 185 mm (L x W x H)
350mm
185 mm
1215 mm
390 mm
698mm

6
PRODUCT OVERVIEW
CONSOLE LCD DISPLAY OVERVIEW
1. ALARM/SNOOZE button
2. LCD display
3. HISTORY button
4. WIND button
5. RAIN button
6. MAX/MIN button
7. CHANNEL button
8. BARO button
9. Stand
10. Wall mounting holder
11. ALERT button
12. ALARM button
13. CLOCK SET button
14. Display brightness setting
15. °C / °F key
16. WI-FI/SENSOR button
17. Battery compartment
18. Power jack
19. DOWN/INDEX button
20. UP/CONTRAST button
21. RESET key
22. REFRESH button
2
NOTE:
This instruction manual contains useful information on the proper use and care of this product. Please read
this manual through to fully understand and enjoy its features, and keep it handy for future use.
OVERVIEW
CONSOLE
1
2
3
4
6
7
5
8
12
13
10
14
21
20
19
15
16
17
18
22
11
9
1. [ ALARM/SNOOZE ] key
2. LCD display
3. [ HISTORY ] key
4. [ WIND ] key
5. [ RAIN ] key
6. [ MAX / MIN ] key
7. [ CHANNEL ] key
8. [ BARO ] key
9. Table stand
10. Wall mounting holder
11. [ ALERT ] key
12. [ ALARM ] key
13. [ CLOCK SET ] key
14. [ HI / LO / AUTO ] key
15. [ °C / °F ] slide switch
16. [ SENSOR / WI-FI ] key
17. Battery door
18. USB Power socket
19. [ / NDX ] key
20. [ / ] key
21. [ RESET ] key
22. [ REFRESH ] key
LCD DISPLAY
1
2
3
5
6
7
8
4
1. Time Calendar & moon phase
2. Wind direction & speed
3. Weather forecast
4. Outdoor temperature & humidity
5. Rainfall & Rain rate
6. Weather Index
7. Barometer
8. Indoor (Ch) temperature & humidity
2
NOTE:
This instruction manual contains useful information on the proper use and care of this product. Please read
this manual through to fully understand and enjoy its features, and keep it handy for future use.
OVERVIEW
CONSOLE
1
2
3
4
6
7
5
8
12
13
10
14
21
20
19
15
16
17
18
22
11
9
1. [ ALARM/SNOOZE ] key
2. LCD display
3. [ HISTORY ] key
4. [ WIND ] key
5. [ RAIN ] key
6. [ MAX / MIN ] key
7. [ CHANNEL ] key
8. [ BARO ] key
9. Table stand
10. Wall mounting holder
11. [ ALERT ] key
12. [ ALARM ] key
13. [ CLOCK SET ] key
14. [ HI / LO / AUTO ] key
15. [ °C / °F ] slide switch
16. [ SENSOR / WI-FI ] key
17. Battery door
18. USB Power socket
19. [ / NDX ] key
20. [ / ] key
21. [ RESET ] key
22. [ REFRESH ] key
LCD DISPLAY
1
2
3
5
6
7
8
4
1. Time Calendar & moon phase
2. Wind direction & speed
3. Weather forecast
4. Outdoor temperature & humidity
5. Rainfall & Rain rate
6. Weather Index
7. Barometer
8. Indoor (Ch) temperature & humidity
1
2
3 6
4 7
5 8
9
10
19
11
20
21
22
12
13
14
15
16
17
18

7
LCD DISPLAY OVERVIEW
1. Time, date, & moon phase
2. Wind direction & speed
3. Weather forecast
4. Outdoor temperature & humidity
5. Rain data
6. Feels like index
7. Barometric pressure
8. Indoor temperature & humidity (CH)
2
NOTE:
This instruction manual contains useful information on the proper use and care of this product. Please read
this manual through to fully understand and enjoy its features, and keep it handy for future use.
OVERVIEW
CONSOLE
1
2
3
4
6
7
5
8
12
13
10
14
21
20
19
15
16
17
18
22
11
9
1. [ ALARM/SNOOZE ] key
2. LCD display
3. [ HISTORY ] key
4. [ WIND ] key
5. [ RAIN ] key
6. [ MAX / MIN ] key
7. [ CHANNEL ] key
8. [ BARO ] key
9. Table stand
10. Wall mounting holder
11. [ ALERT ] key
12. [ ALARM ] key
13. [ CLOCK SET ] key
14. [ HI / LO / AUTO ] key
15. [ °C / °F ] slide switch
16. [ SENSOR / WI-FI ] key
17. Battery door
18. USB Power socket
19. [ / NDX ] key
20. [ / ] key
21. [ RESET ] key
22. [ REFRESH ] key
LCD DISPLAY
1
2
3
5
6
7
8
4
1. Time Calendar & moon phase
2. Wind direction & speed
3. Weather forecast
4. Outdoor temperature & humidity
5. Rainfall & Rain rate
6. Weather Index
7. Barometer
8. Indoor (Ch) temperature & humidity
1
5
2
6
37
48

8
WIRELESS 5-IN-1 OUTDOOR SENSOR OVERVIEW
3
WIRELESS 5-IN-1 SENSOR
4
5
6
1
2
3
7
8
10
9
11
1. Antenna
2. Radiation shield & Thermo-hygro sensor
3. Mounting parts (t for 35 ~40mm diameter
pole)
4. Battery door
5. [ RESET ] key
6. Transmission status LED
7. Bubble level gradienter
8. Rain collector
9. Wind vane
10. Solar panel
11. Wind cups
1
7
9
10
11
8
3
4
2
5
6

9
1. Antenna
2. Radiation shield &
hygro-thermo sensor
3. Mounting parts
4. Battery door
5. RESET button
6. Transmission status LED
7. Bubble level gradienter
8. Rain collector
INSTALLATION INSTRUCTIONS
The display console can pair up with one (1) wireless 5-in-1 outdoor sensor and up to seven (7) wireless
indoor sensors. (NOTE: This product does not include an indoor sensor.)
Screwdriver
9. Wind direction vane
10. Solar panel
11. Wind speed cups
RECOMMENDED TOOL

10
SETTING UP RAIN COLLECTOR
INSTALLING THE BATTERIES
MOUNTING SENSOR ON POLE
1. Align the notches on the funnel with the lock grooves inside the rain collector.
2. Insert the funnel in the rain collector and screw on tight to lock it in place.
1. Unscrew the battery door at the bottom of the 5-in-1 outdoor sensor.
2. Insert three (3) AA batteries (not included) according to the +/- polarity labeled in the compartment.
3. Screw the battery door back onto the compartment.
NOTE: The LED light will ash red every 12 seconds.
1. Pick a location for the 5-in-1 outdoor sensor that is open with no obstructions.
2. Set the sensor so the rain collector faces north and solar panel faces south.
4
INSTALLATION AND SETUP
Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 wireless indoor
sensors. (1pc wireless indoor sensor included)
INSTALL WIRELESS 7-IN-1 SENSOR
Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity,
temperature and humidity for you. It’s assembled and calibrated for your easy installation.
INSTALL RAIN COLLECTOR
Rain Collector Installation
1 Align
Lock grooves
2 Lock
INSTALL BATTERIES
Unscrew the battery door at bottom of unit and insert the batteries
according to the +/- polarity indicated. Screw the battery door
compartment on tightly.
NOTE:
The red LED will begin ashing every 12 seconds.
Screw
location
3 x AA
batteries
MOUNTING POLE AND DIRECTION ALIGNMENT
Install the wireless 7-IN-1 sensor in an open
location with no obstructions above and around the
sensor for accurate rain and wind measurement.
Install the sensor with the smaller end facing the
North to properly orient the wind direction vane.
Secure the mounting stand and bracket (included)
to a 35 ~ 40mm diameter steel post or pole, and
allow minimum 2m off the ground.
Point to
SOUTH
Point to
NORTH
2 meter
off the
ground
mounting pole
and stand not
included
Add rubber
pad before
mounting on
pole or post
4
INSTALLATION AND SETUP
Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 wireless indoor
sensors. (1pc wireless indoor sensor included)
INSTALL WIRELESS 7-IN-1 SENSOR
Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity,
temperature and humidity for you. It’s assembled and calibrated for your easy installation.
INSTALL RAIN COLLECTOR
Rain Collector Installation
1 Align
Lock grooves
2 Lock
INSTALL BATTERIES
Unscrew the battery door at bottom of unit and insert the batteries
according to the +/- polarity indicated. Screw the battery door
compartment on tightly.
NOTE:
The red LED will begin ashing every 12 seconds.
Screw
location
3 x AA
batteries
MOUNTING POLE AND DIRECTION ALIGNMENT
Install the wireless 7-IN-1 sensor in an open
location with no obstructions above and around the
sensor for accurate rain and wind measurement.
Install the sensor with the smaller end facing the
North to properly orient the wind direction vane.
Secure the mounting stand and bracket (included)
to a 35 ~ 40mm diameter steel post or pole, and
allow minimum 2m off the ground.
Point to
SOUTH
Point to
NORTH
2 meter
off the
ground
mounting pole
and stand not
included
Add rubber
pad before
mounting on
pole or post
SETTING UP THE WIRELESS 5-IN-1 OUTDOOR SENSOR
The wireless 5-in-1 outdoor sensor measures wind speed, wind direction, rainfall, temperature, and
humidity.
1
2

11
The outdoor wireless weather sensor is calibrated to be pointed north for maximum accuracy. However,
for your convenience, if you are a user located in the Southern Hemisphere, you can use the sensor with
the wind vane pointing south.
1. Mount and install the wireless weather sensor with the wind meter end pointed South, instead of
North. (Please refer to Mounting Sensor on Pole for mounting instructions.)
2. Select “S” in hemisphere section of the setup UI setup page. (Please refer to Setting Up Weather
Server Connection section for setup details)
3. Press the APPLY icon to conrm and exit.
NOTES: Changing the hemisphere setting will automatically switch the direction of the moon
phases on the display.
Pointing the wireless weather sensor toward the south will allow maximum sunlight on the solar
panel, especially during the winter season in the Southern Hemisphere.
POINTING THE WIRELESS 5-IN-1 OUTDOOR SENSOR TO SOUTH (OPTIONAL)
4
INSTALLATION AND SETUP
Your console can pair up with one wireless 7-in-1 outdoor sensor and up to 7 wireless indoor
sensors. (1pc wireless indoor sensor included)
INSTALL WIRELESS 7-IN-1 SENSOR
Your wireless 7-IN-1 sensor measures wind-speed, wind-direction, rainfall, UV, light intensity,
temperature and humidity for you. It’s assembled and calibrated for your easy installation.
INSTALL RAIN COLLECTOR
Rain Collector Installation
1 Align
Lock grooves
2 Lock
INSTALL BATTERIES
Unscrew the battery door at bottom of unit and insert the batteries
according to the +/- polarity indicated. Screw the battery door
compartment on tightly.
NOTE:
Screw
location
3 x AA
batteries
MOUNTING POLE AND DIRECTION ALIGNMENT
Install the wireless 7-IN-1 sensor in an open
location with no obstructions above and around the
sensor for accurate rain and wind measurement.
Install the sensor with the smaller end facing the
North to properly orient the wind direction vane.
Secure the mounting stand and bracket (included)
to a 35 ~ 40mm diameter steel post or pole, and
allow minimum 2m off the ground.
Point to
SOUTH
Point to
NORTH
2 meters
off the
ground
mounting pole
and stand not
included
Add rubber
pad before
mounting on
pole or post
3. Secure the sensor onto a mounting post or pole (not included) using the mounting clamp (included).
4. Add rubber pads onto mounting clamp before fastening the mounting clamp onto the sensor.
5. Tighten the mounting clamp using included screws onto the bottom of the sensor once it is on a pole.
NOTE: Place sensor a minimum of 6.6 ft (2 m) o the ground on a steel post or pole with a 1.4” -
1.6” (35 - 40 mm) diameter).

12
Your console can pair up with one (1) wireless 5-in-1 outdoor sensor and up to seven (7) wireless
indoor sensors. (No indoor sensors included.)
1. Remove the battery door on the rear of the console.
2. Insert a new button battery.
3. Replace the battery door.
NOTE: The backup battery can assist with backing up the time & date, MAX/MIN data, weather
records from the past 24 hours, alert settings, the oset value of weather data, and the
sensor(s) channel history. The built-in memory will backup router and weather server settings.
1. Plug the power adapter into the power jack located on back of the console.
2. Once the console is turned on, it will automatically enter pairing mode.
NOTE: If the LCD display does not turn on, use a pin or other small object to press the RESET
button on back of the console.
NOTE: The weather console can be mounted to a wall using a single hook or screw, or can stand
on a table, desk, or shelf using the included stand.
1. Line up the stand so that the bottom bracket clips into the bottom mount on the console.
2. Lift the leg of the stand until the top bracket clips into the top mount on the console.
While in normal operating mode, use the UP or DOWN key to adjust the viewing angle of the LCD
display to t your viewing needs.
SETTING UP THE WEATHER CONSOLE
INSTALLING THE BACKUP BATTERIES
POWERING UP THE CONSOLE
ATTACHING THE STAND
SETTING THE LCD DISPLAY ANGLE

13
PAIRING THE WIRELESS 5-IN-1 SENSOR AND INDOOR SENSOR
RESET AND FACTORY HARD RESET
RE-PAIRING SENSORS
CHANGING BATTERIES AND MANUAL PAIRING OF SENSOR
PAIRING ADDITIONAL WIRELESS SENSORS
1. Once your display console powers on, it should automatically search for and connect to the wireless
weather sensors. If the console does not connect within the rst 15 minutes, refer to the following
section, Changing Batteries and Manual Pairing of Sensor, for instructions on manual pairing.
2. You will see the icon of an antenna blinking in the temperature and humidity (outdoor) section of the
display.
3. Once the pairing process completes, the antenna icon will appear solid (not blinking), and the
readings for outdoor temperature and humidity, wind speed, wind direction, and rainfall will appear
in their designated sections of the LCD display.
To reset the console and start again, press the RESET button once. To hard reset the console and
revert to factory settings, press and hold the RESET button on the console for six (6) seconds.
If the connection fails or the console is reset, press the WI-FI/SENSOR button once for the console to
enter pairing mode. The console will re-register all the sensors that have already been registered to it
before. (i.e. the console will not lose the connection of the sensors that you have paired up before.)
Whenever you change the batteries of the wireless indoor or 5-in-1 weather sensor, re-pairing must be
done manually.
1. Change all the batteries in the sensor.
2. Press the WI-FI/SENSOR button on the console to enter pairing mode.
3. Press the RESET button on the wireless indoor or 5-in-1 weather sensor.
1. Press the WI-FI/SENSOR button once on the console to enter pairing mode.
2. Press the RESET button on the new sensor and wait for a few minutes for the new sensor to pair to
the console.
NOTE: Channel number of an indoor sensor must not be the same as another indoor sensor. Please
refer to Setting Up the Wireless Indoor Hygro-thermo Sensor section for details.
6
1. Remove the battery door of the console.
2. Insert 3 new AAA batteries as per the polarity indicated,
3. Replace the battery door.
BUILT-IN MEMORY
The console has built-in FLASH memory that holds the vital settings. These include:
-Time Zone, DST status, Time SYNC status, WI-FI and Weather server setting, Latitude /
Longitude, Hemisphere setting, Calibration values, and Sensor ID of paired sensor(s)
RESET AND FACTORY HARD RESET
To reset the console and start again, press the [ RESET ] key once. To hard reset the
console and resume factory settings, press and hold the [ RESET ] key for 6 seconds
RESYNCHRONIZE SENSORS
Press the [ SENSOR / WI-FI ] key once for the console to enter sensor Synchronization mode,
and the console will re-register all the sensors that have already been registered to it before.
i.e. the console will not lose the connection of the sensors that you’d paired up before.
CHANGING BATTERIES AND MANUAL PAIRING OF SENSOR
Whenever you changed the batteries of the wireless indoor or 7-in-1 weather sensor, re-
synchronization must be done manually.
1. Change all the batteries to new ones in the sensor.
2. Press [ SENSOR / WI-FI ] key on the console to enter sensor synchronization mode.
3. Press [ RESET ] key on the wireless indoor or 7-in-1 weather sensor.
SYNCHRONIZING ADDITIONAL WIRELESS SENSOR(S) (OPTIONAL)
The console can support up to 7 additional wireless sensors.
1. Press the [ SENSOR / WI-FI ] key once on the console to enter synchronization mode.
2. Press the [ RESET ] key on the new sensor, and wait for a few minutes for the new sensor
to paired to the console.
NOTE:
- Channel number of the indoor sensor must not be duplicated among the sensors. Please refer
to “INSTALL WIRELESS INDOOR SENSOR” for details
- This console can support different type of additional wireless sensor, e.g. soil moisture and
pool sensor. If you would like to pair up additional sensors, please check with your retailer for
more detail.
POINTING THE WIRELESS 7-IN-1 SENSOR TO SOUTH
The outdoor 7-IN-1 sensor is calibrated to point to North for the maximum accuracy. However,
for the user's convenience (e.g. users in the Southern hemisphere), it is possible to use the
sensor with the wind vane pointing to South.
1. Install the 7-IN-1 wireless sensor with its wind meter end pointing to South. (Please refer to
INSTALLATION OF THE WIRELESS SENSOR section for mounting details)
2. Select "S' in hemisphere section of the setup UI setup page. (Please refer to SETUP THE
WEATHER SERVER CONNECTION section for setup details)
3. Press Apply icon to conrm and exit.
NOTE:
Changing the hemisphere setting will automatically switch the direction of the moon phase on
the display.

14
When you rst power up the console or press and hold the WI-FI/SENSOR button for six (6) seconds, the
console LCD display will show the letters “AP” and an icon to signify that it has entered Access
Point (AP) mode. At this time it will be ready for the Wi-Fi®settings to be adjusted.
Use your smartphone, tablet, or computer to connect to the console via Wi-Fi®by following these steps:
1. On PC, open your Wi-Fi® network settings. On Android™ or iOS devices, go to settings menu and
then select Connections/WI-FI to open the network settings.
2. Locate the display console’s SSID from the list. It should appear as PWS-XXXXXX (where all the X’s
are integers) in the list. Tap on the SSID to connect. This step will take several seconds.
3. Once you are connected to the display console, open up your internet browser, and enter the
following address into the address bar: http://192.168.1.1 (make sure to include the http:// or
else the web browser may interpret the address as a search query). We recommend using the latest
version of reputable web browsers.
The following icons on the LCD display screen show the Wi-Fi®status:
Once you are connected via Wi-Fi®to the display console and have opened the settings page at
http://192.168.1.1, enter the following information into the web interface setup page. If you have chosen
not to use Weather Underground or Weathercloud servers, leave the check boxes unchecked.
SETUP INSTRUCTIONS
SETTING UP WI-FI®CONNECTION
WI-FI®CONNECTION STATUS
SETTING UP WEATHER SERVER CONNECTION
10
SETUP THE WEATHER SERVER CONNECTION
Enter the following information into the below web interface "SETUP" page. If you choose not
to use Wunderground.com or Weathercloud.net, leave the check boxes unchecked.
Function firmware version: 1.00
WiFi firmware version: 1.00
nist.time.gov
Server URL:
Time server setup
WiFi Router setup
SETUP ADVANCED
Wunderground
Station ID:
WDw124
******
******
******
IPACIR23Wc
Weather server setup
Station key:
Router:
Add Router
Search
Security type:
Router Password:
WAP2
ROUTER_A
Apply
Language: English
Weathercloud
Station ID:
Station key:
Mac address 00:0E:C6:00:07:10
Press to search router Select the Wi-fi router (SSID) you will connect to
Manually enter the SSID if not on the list
Select router’s security type (usually WAP2)
Check to confirm upload to Weather Underground
Enter new Station ID and Station key assigned
by Wunderground (Weather Underground)
Check to confirm upload to Weathercloud
Select time server
Press to complete the setting
SETUP page
Router’s password (leave blank if unsecured)
Press to allow add
router manually
Password record remark
(If you entered password)
Current ID and
key recorded (if any)
Current ID and key
recorded (if any)
Enter new Station ID and Station key
assigned by Weathercloud
Solid: the display console is
connected to your wireless router
Flashing: the display console is
attempting to connect to your wireless router
Flashing: the display console is
currently in AP (access point) mode
Press “SETUP” icon
to SETUP page
NOTE:
- When WI-FI setup is complete, your PC or mobile will resume your default WI-FI connection.
- During AP mode, you can press and hold the [ WI-FI / SENSOR ] key for 6 seconds to stop
AP mode and the console will restore your previous setting.
WI-FI CONNECTION STATUS
Below is the WI-FI icon status on the console LCD:
Flashing: Console is trying to
connect to WI-FI router
TIME SERVER CONNECTION STATUS
After the console has connected to the internet, it will attempt to connect to the internet time
server to obtain the UTC time. Once the connection succeeds and the console's time has been
updated, the “ ” icon will appear on the LCD.
Time zone: To display the time of your time-zone, change the time zone in CLOCK setting mode
from '00' (default) to your time zone (e.g.08 for Hong Kong).
1.Press and hold [ CLOCK SET ] key for 2s to enter time setting mode.
2.Press [ ] or [ ] key to enter your time zone, then press and hold [ CLOCK SET ] key
setting for the console.

15
11
SETUP THE WEATHER SERVER CONNECTION
Enter the following information into the below web interface "SETUP" page to connect the
console to weather server, If you do not want to use Wunderground.com or Weathercloud.net,
please empty the station ID & key to ignore the data upload.
nist.time.gov
Server URL:
0.0000 North
*Latitude:
0.0000
Enter 0 to 90, no negative numbers
Enter 0 to 180, no negative numbers
East
*Longitude:
Time server setup
Location for sunrise / sunset
WiFi Router setup
ADVANCED
Wunderground
Station ID: WDw124
******
******
******
IPACIR23Wc
Weather server setup
Station key:
Router:
Add Router
Search
Security type:
Router Password:
WAP2
ROUTER_A
Language: English
Weathercloud
Station ID:
Station key:
******
IDCR21w1
http://WAC.com
Station ID:
URL:
Station key:
Mac address 00:0E:C6:00:07:10
Hemisphere
* Depends on the model
SETUP
Apply
Firmware version: 1.00
0:00
Time Zone:
N
Press "ADVANCED" icon
to Advanced page
Press to search router
Press to allow add
router manually
E
nter the Latitude value
Enter the Longitude
value
SETUP page
Select setup UI display language
Press to complete the setting
Select router (SSID) for connection
Enter new Station ID and Station key
that assigned by Wundergriund
Enter new Station ID and Station key
that assigned by weathercloud
Enter new Station ID and Station key
that assigned by the corresponding
weather server
Manually enter the SSID if not on list
Select time server
Select time zone of your location
Select the direction (e.g. EU
countries Longitude is East and US
is West)
Select the sensor located hemisphere
(e.g. US and EU countries are also "N"
,
Australia is "S")
Reserved for validated weather server,
detail please consult with your retailer
Select router's security type (usually
WAP2)
Router's password (leave blank if the
Security type is "Open")
SETTINGS
NOTE:
- When WI-FI setup is completed, your PC or mobile will resume your default WI-FI connection.
- During AP mode, you can press and hold the [ SENSOR / WI-FI ] key for 6 seconds to stop
AP mode and the console will restore your previous setting.
TIME ZONE
To automtically set the time display to your time-zone, change the time zone in SETUP page of
previous section from '0:00' (default) to your time zone (e.g.+1:00 for Germany).
nist.time.gov
Server URL:
Time server setup
0:00
Time Zone:
NOTES: When the Wi-Fi® setup is complete, your computer or mobile device will return to the
default Wi-Fi® connection. If it does not, simply open your device’s wireless network settings
and manually reconnect.
While in AP mode, you can press and hold the WI-FI/SENSOR button for six (6) seconds to exit
AP mode. The display console will simply restore the previous AP settings.

16
TIME ZONE
TIME SERVER CONNECTION STATUS
To automatically set the time display to your time-zone, change the time zone in Time server setup
section of the SETUP page from ‘0:00’ (default) to your time zone (e.g.+1:00 for Germany).
Once the display console has connected to the internet, it will attempt to connect to the internet time
server to obtain the UTC time. Once the connection is successful and the time has been updated, the
icon will appear below the Wi-Fi®icon on the LCD.
To display the correct time for your specic time zone, you’ll need to change the time zone in the
CLOCK setting mode from 00 (default) to your specic time zone (e.g. -5 for EST). If you don’t know
your time zone, you can look it up online.
1. In normal operating mode, press and hold the CLOCK button for two (2) seconds to enter the
clock setting menu.
2. Press the UP or DOWN buttons to adjust the time zone, then press and hold the CLOCK button
for two (2) seconds to conrm and exit the menu. Please refer to the Setting the Time section of
the manual on page 22 for details of other available clock settings.
The time will automatically sync with the internet time server at 12:00AM and 12:00PM per day. Also
you can press the REFRESH button to get the internet time manually within one (1) minute.
ADVANCED SETTINGS VIA WEB INTERFACE
Once you are connected via Wi-Fi®to the display console and have opened the settings page at
http://192.168.1.1, clicking on the tab that says ADVANCED will open the following page. This page
will allow you to set and view specic calibration data of your display console, and also update the
rmware if you are on PC.
11
SETUP THE WEATHER SERVER CONNECTION
Enter the following information into the below web interface "SETUP" page to connect the
console to weather server, If you do not want to use Wunderground.com or Weathercloud.net,
please empty the station ID & key to ignore the data upload.
nist.time.gov
Server URL:
0.0000 North
*Latitude:
0.0000
Enter 0 to 90, no negative numbers
Enter 0 to 180, no negative numbers
East
*Longitude:
Time server setup
Location for sunrise / sunset
WiFi Router setup
ADVANCED
Wunderground
Station ID: WDw124
******
******
******
IPACIR23Wc
Weather server setup
Station key:
Router:
Add Router
Search
Security type:
Router Password:
WAP2
ROUTER_A
Language: English
Weathercloud
Station ID:
Station key:
******
IDCR21w1
http://WAC.com
Station ID:
URL:
Station key:
Mac address 00:0E:C6:00:07:10
Hemisphere
* Depends on the model
SETUP
Apply
Firmware version: 1.00
0:00
Time Zone:
N
Press "ADVANCED" icon
to Advanced page
Press to search router
Press to allow add
router manually
E
nter the Latitude value
Enter the Longitude
value
SETUP page
Select setup UI display language
Press to complete the setting
Select router (SSID) for connection
Enter new Station ID and Station key
that assigned by Wundergriund
Enter new Station ID and Station key
that assigned by weathercloud
Enter new Station ID and Station key
that assigned by the corresponding
weather server
Manually enter the SSID if not on list
Select time server
Select time zone of your location
Select the direction (e.g. EU
countries Longitude is East and US
is West)
Select the sensor located hemisphere
(e.g. US and EU countries are also "N"
,
Australia is "S")
Reserved for validated weather server,
detail please consult with your retailer
Select router's security type (usually
WAP2)
Router's password (leave blank if the
Security type is "Open")
SETTINGS
NOTE:
- When WI-FI setup is completed, your PC or mobile will resume your default WI-FI connection.
- During AP mode, you can press and hold the [ SENSOR / WI-FI ] key for 6 seconds to stop
AP mode and the console will restore your previous setting.
TIME ZONE
To automtically set the time display to your time-zone, change the time zone in SETUP page of
previous section from '0:00' (default) to your time zone (e.g.+1:00 for Germany).
nist.time.gov
Server URL:
Time server setup
0:00
Time Zone:
12
TIME SERVER CONNECTION STATUS
After the console has connected to the internet, it will
attempt to connect to the internet time server to obtain
the UTC time. Once the connection succeeds and the
console's time has been updated, the “ ” icon will
appear on the LCD.
The time will automatically synchronize Internet time server at 12:00AM and 12:00PM per day.
Also you can press the [REFRESH ] key to get the internet time manually within 1 minute.
ADVANCE SETTING IN WEB INTERFACE
Press "ADVANCED" key at the top of web interface to enter the advance setting page, this
page allow you to set and view the calibration data of the console, as well as update the
rmware version on PC web browser.
Upload
Browse
Firmware version: 1.00
-560~ 560hpa / -16.54 ~ 16.54inHg / -420 ~ 420mmHg
Setting Range:
Temperature oC
Outdoor
Indoor
CH 1
CH 2
CH 3
CH 4
CH 5
CH 6
CH 7
Humidity %
Relative Pressure Offset:
Absolute Pressure Offset:
hpa
Range: -20 ~ 20
(Default: 0.0)
Current offset: 10Current offset: -9
Current offset: -5Current offset: 2
Current offset: -2Current offset: 3
Current offset: -2Current offset: 1.2
Current offset: -5Current offset: -0.2
Current offset: -3Current offset: -20.1
Current offset: -10Current offset: 11.5
Current offset: -3
Current offset: -3
(Default: 0)
Current offset: 10
(Default: 0)
Current offset: 0.2
Current offset: -5Current offset: 1
Pressure
Range: -20.0 ~ 20.0oC
-36.0 ~ 36.0oF (Default: 0.0)
*UV gain: Range: 0.01 ~ 10(Default: 1.00)
Current gain: 1.1
*Light gain: Range: 0.01 ~ 10(Default: 1.00)
Current gain: 1.1
* Depends on the model
*Wind speed gain:
*Wind direction:
*Rain gain: Range: 0.5 ~ 1.5(Default: 1.00)
Range: -10 ~ 10(Default: 0o)
Range: 0.5 ~ 1.5(Default: 1.00)
Current gain: 0.85
Current offset: 2o
Current gain: 0.75
SETUP ADVANCED
Select setting unit
Press "SETUP" icon to
Setup page
Outdoor and Ch 1~7
temperature calibration
section
Pressure calibration
section
version
function only available
in PC web browser
ADVAN
C
ED page
Select setting unit
The rain, wind speed, UV and Light
calibration use gain method. The
wind direction is +/- 10 offset.
Outdoor and Ch 1~7 humidity
calibration section
Current offset value is the value
that you set before to offset the
pressure reading.
SETTINGS
CALIBRATION
1.User can input the offset and/or gain values for different parameters while current offset and
gain values are shown next to their corresponding blank.
2.Once completed, press Apply at the bottom of the SETUP page
The current offset value will show the previous value that you entered, please input the new
value in the blank if any changes needed, the new value will effective once you press Apply
icon in SETUP page.
12
TIME SERVER CONNECTION STATUS
After the console has connected to the internet, it will
attempt to connect to the internet time server to obtain
the UTC time. Once the connection succeeds and the
console's time has been updated, the “ ” icon will
appear on the LCD.
The time will automatically synchronize Internet time server at 12:00AM and 12:00PM per day.
Also you can press the [REFRESH ] key to get the internet time manually within 1 minute.
ADVANCE SETTING IN WEB INTERFACE
Press "ADVANCED" key at the top of web interface to enter the advance setting page, this
page allow you to set and view the calibration data of the console, as well as update the
rmware version on PC web browser.
Upload
Browse
Firmware version: 1.00
-560~ 560hpa / -16.54 ~ 16.54inHg / -420 ~ 420mmHg
Setting Range:
Temperature oC
Outdoor
Indoor
CH 1
CH 2
CH 3
CH 4
CH 5
CH 6
CH 7
Humidity %
Relative Pressure Offset:
Absolute Pressure Offset:
hpa
Range: -20 ~ 20
(Default: 0.0)
Current offset: 10Current offset: -9
Current offset: -5Current offset: 2
Current offset: -2Current offset: 3
Current offset: -2Current offset: 1.2
Current offset: -5Current offset: -0.2
Current offset: -3Current offset: -20.1
Current offset: -10Current offset: 11.5
Current offset: -3
Current offset: -3
(Default: 0)
Current offset: 10
(Default: 0)
Current offset: 0.2
Current offset: -5Current offset: 1
Pressure
Range: -20.0 ~ 20.0oC
-36.0 ~ 36.0oF (Default: 0.0)
*UV gain: Range: 0.01 ~ 10(Default: 1.00)
Current gain: 1.1
*Light gain: Range: 0.01 ~ 10(Default: 1.00)
Current gain: 1.1
* Depends on the model
*Wind speed gain:
*Wind direction:
*Rain gain: Range: 0.5 ~ 1.5(Default: 1.00)
Range: -10 ~ 10(Default: 0o)
Range: 0.5 ~ 1.5(Default: 1.00)
Current gain: 0.85
Current offset: 2o
Current gain: 0.75
SETUP ADVANCED
Select setting unit
Press "SETUP" icon to
Setup page
Outdoor and Ch 1~7
temperature calibration
section
Pressure calibration
section
version
function only available
in PC web browser
ADVAN
C
ED page
Select setting unit
The rain, wind speed, UV and Light
calibration use gain method. The
wind direction is +/- 10 offset.
Outdoor and Ch 1~7 humidity
calibration section
Current offset value is the value
that you set before to offset the
pressure reading.
SETTINGS
CALIBRATION
1.User can input the offset and/or gain values for different parameters while current offset and
gain values are shown next to their corresponding blank.
2.Once completed, press Apply at the bottom of the SETUP page
The current offset value will show the previous value that you entered, please input the new
value in the blank if any changes needed, the new value will effective once you press Apply
icon in SETUP page.

17
12
TIME SERVER CONNECTION STATUS
After the console has connected to the internet, it will
attempt to connect to the internet time server to obtain
the UTC time. Once the connection succeeds and the
console's time has been updated, the “ ” icon will
appear on the LCD.
The time will automatically synchronize Internet time server at 12:00AM and 12:00PM per day.
Also you can press the [REFRESH ] key to get the internet time manually within 1 minute.
ADVANCE SETTING IN WEB INTERFACE
Press "ADVANCED" key at the top of web interface to enter the advance setting page, this
page allow you to set and view the calibration data of the console, as well as update the
rmware version on PC web browser.
Upload
Browse
Firmware version: 1.00
-560~ 560hpa / -16.54 ~ 16.54inHg / -420 ~ 420mmHg
Setting Range:
Temperature oC
Outdoor
Indoor
CH 1
CH 2
CH 3
CH 4
CH 5
CH 6
CH 7
Humidity %
Relative Pressure Offset:
Absolute Pressure Offset:
hpa
Range: -20 ~ 20
(Default: 0.0)
Current offset: 10Current offset: -9
Current offset: -5Current offset: 2
Current offset: -2Current offset: 3
Current offset: -2Current offset: 1.2
Current offset: -5Current offset: -0.2
Current offset: -3Current offset: -20.1
Current offset: -10Current offset: 11.5
Current offset: -3
Current offset: -3
(Default: 0)
Current offset: 10
(Default: 0)
Current offset: 0.2
Current offset: -5Current offset: 1
Pressure
Range: -20.0 ~ 20.0oC
-36.0 ~ 36.0oF (Default: 0.0)
*UV gain: Range: 0.01 ~ 10(Default: 1.00)
Current gain: 1.1
*Light gain: Range: 0.01 ~ 10(Default: 1.00)
Current gain: 1.1
* Depends on the model
*Wind speed gain:
*Wind direction:
*Rain gain: Range: 0.5 ~ 1.5(Default: 1.00)
Range: -10 ~ 10(Default: 0o)
Range: 0.5 ~ 1.5(Default: 1.00)
Current gain: 0.85
Current offset: 2o
Current gain: 0.75
SETUP ADVANCED
Select setting unit
Press "SETUP" icon to
Setup page
Outdoor and Ch 1~7
temperature calibration
section
Pressure calibration
section
version
function only available
in PC web browser
ADVAN
C
ED page
Select setting unit
The rain, wind speed, UV and Light
calibration use gain method. The
wind direction is +/- 10 offset.
Outdoor and Ch 1~7 humidity
calibration section
Current offset value is the value
that you set before to offset the
pressure reading.
SETTINGS
CALIBRATION
1.User can input the offset and/or gain values for different parameters while current offset and
gain values are shown next to their corresponding blank.
2.Once completed, press Apply at the bottom of the SETUP page
The current offset value will show the previous value that you entered, please input the new
value in the blank if any changes needed, the new value will effective once you press Apply
icon in SETUP page.
CALIBRATION
1. You may enter or change the oset and gain values for dierent measurement parameters
while viewing the current oset and gain values next to the corresponding boxes.
2. Once you have completed your calibrations, press the button on the SETUP tab.
3. The current oset value will update to show the value that you entered (instead of the default
value). If you want to change the value, you can enter a new value in the box beside the number
(as in step 1). To update the value, again, press in the SETUP tab.
NOTE: We do not recommend calibration of most values with the exception of Relative
Pressure, which must be correctly calibrated to reect your distance above sea level to
account for altitude eects.
6
1. Remove the battery door of the console.
2. Insert 3 new AAA batteries as per the polarity indicated,
3. Replace the battery door.
BUILT-IN MEMORY
The console has built-in FLASH memory that holds the vital settings. These include:
-Time Zone, DST status, Time SYNC status, WI-FI and Weather server setting, Latitude /
Longitude, Hemisphere setting, Calibration values, and Sensor ID of paired sensor(s)
RESET AND FACTORY HARD RESET
To reset the console and start again, press the [ RESET ] key once. To hard reset the
console and resume factory settings, press and hold the [ RESET ] key for 6 seconds
RESYNCHRONIZE SENSORS
Press the [ SENSOR / WI-FI ] key once for the console to enter sensor Synchronization mode,
and the console will re-register all the sensors that have already been registered to it before.
i.e. the console will not lose the connection of the sensors that you’d paired up before.
CHANGING BATTERIES AND MANUAL PAIRING OF SENSOR
Whenever you changed the batteries of the wireless indoor or 7-in-1 weather sensor, re-
synchronization must be done manually.
1. Change all the batteries to new ones in the sensor.
2. Press [ SENSOR / WI-FI ] key on the console to enter sensor synchronization mode.
3. Press [ RESET ] key on the wireless indoor or 7-in-1 weather sensor.
SYNCHRONIZING ADDITIONAL WIRELESS SENSOR(S) (OPTIONAL)
The console can support up to 7 additional wireless sensors.
1. Press the [ SENSOR / WI-FI ] key once on the console to enter synchronization mode.
2. Press the [ RESET ] key on the new sensor, and wait for a few minutes for the new sensor
to paired to the console.
NOTE:
- Channel number of the indoor sensor must not be duplicated among the sensors. Please refer
to “INSTALL WIRELESS INDOOR SENSOR” for details
- This console can support different type of additional wireless sensor, e.g. soil moisture and
pool sensor. If you would like to pair up additional sensors, please check with your retailer for
more detail.
POINTING THE WIRELESS 7-IN-1 SENSOR TO SOUTH
The outdoor 7-IN-1 sensor is calibrated to point to North for the maximum accuracy. However,
for the user's convenience (e.g. users in the Southern hemisphere), it is possible to use the
sensor with the wind vane pointing to South.
1. Install the 7-IN-1 wireless sensor with its wind meter end pointing to South. (Please refer to
INSTALLATION OF THE WIRELESS SENSOR section for mounting details)
2. Select "S' in hemisphere section of the setup UI setup page. (Please refer to SETUP THE
WEATHER SERVER CONNECTION section for setup details)
3. Press
Apply
icon to conrm and exit.
NOTE:
Changing the hemisphere setting will automatically switch the direction of the moon phase on
the display.
6
1. Remove the battery door of the console.
2. Insert 3 new AAA batteries as per the polarity indicated,
3. Replace the battery door.
BUILT-IN MEMORY
The console has built-in FLASH memory that holds the vital settings. These include:
-Time Zone, DST status, Time SYNC status, WI-FI and Weather server setting, Latitude /
Longitude, Hemisphere setting, Calibration values, and Sensor ID of paired sensor(s)
RESET AND FACTORY HARD RESET
To reset the console and start again, press the [ RESET ] key once. To hard reset the
console and resume factory settings, press and hold the [ RESET ] key for 6 seconds
RESYNCHRONIZE SENSORS
Press the [ SENSOR / WI-FI ] key once for the console to enter sensor Synchronization mode,
and the console will re-register all the sensors that have already been registered to it before.
i.e. the console will not lose the connection of the sensors that you’d paired up before.
CHANGING BATTERIES AND MANUAL PAIRING OF SENSOR
Whenever you changed the batteries of the wireless indoor or 7-in-1 weather sensor, re-
synchronization must be done manually.
1. Change all the batteries to new ones in the sensor.
2. Press [ SENSOR / WI-FI ] key on the console to enter sensor synchronization mode.
3. Press [ RESET ] key on the wireless indoor or 7-in-1 weather sensor.
SYNCHRONIZING ADDITIONAL WIRELESS SENSOR(S) (OPTIONAL)
The console can support up to 7 additional wireless sensors.
1. Press the [ SENSOR / WI-FI ] key once on the console to enter synchronization mode.
2. Press the [ RESET ] key on the new sensor, and wait for a few minutes for the new sensor
to paired to the console.
NOTE:
- Channel number of the indoor sensor must not be duplicated among the sensors. Please refer
to “INSTALL WIRELESS INDOOR SENSOR” for details
- This console can support different type of additional wireless sensor, e.g. soil moisture and
pool sensor. If you would like to pair up additional sensors, please check with your retailer for
more detail.
POINTING THE WIRELESS 7-IN-1 SENSOR TO SOUTH
The outdoor 7-IN-1 sensor is calibrated to point to North for the maximum accuracy. However,
for the user's convenience (e.g. users in the Southern hemisphere), it is possible to use the
sensor with the wind vane pointing to South.
1. Install the 7-IN-1 wireless sensor with its wind meter end pointing to South. (Please refer to
INSTALLATION OF THE WIRELESS SENSOR section for mounting details)
2. Select "S' in hemisphere section of the setup UI setup page. (Please refer to SETUP THE
WEATHER SERVER CONNECTION section for setup details)
3. Press
Apply
icon to conrm and exit.
NOTE:
Changing the hemisphere setting will automatically switch the direction of the moon phase on
the display.

18
Your display console can upload weather data to Weather Underground and/or Weathercloud via your
Wi-Fi®router.
NOTE: Logia™ does not own Weather Underground or Weathercloud, and these instructions are
liable to change without notice due to changes in either website.
CREATE AND SYNC YOUR WEATHER SERVER ACCOUNT
CREATE YOUR WEATHER UNDERGROUND ACCOUNT
1. Make sure your display console is connected to your Wi-Fi® network, as outlined in brief below.
Detailed steps are available in the Setting up Wi-Fi®Connection segment on page 14 of this user
guide. The display console must be connected to the Wi-Fi®network in order to communicate
with Weather Underground.
a. Press and hold the WI-FI/SENSOR button for six (6) seconds to put your display console
into AP mode.
b. Open your phone, tablet, or computer’s wireless settings to search for a wireless network.
c. Locate the display console’s SSID in the list and select it.
d. Once connected, open up your device’s web browser and enter https://192.168.1.1
2. Visit the Weather Underground website at https://www.wunderground.com and click the link
that says “JOIN”. Follow the instructions to create an account.
NOTE: Please use a valid email address to register your account.
3. Once you have created your account and completed the email validation process, return to the
Weather Underground website. Click the dropdown link at the top of the site that says MORE,
and then select Add Weather Station from the dropdown menu.
4. Follow the instructions on screen to enter your weather station information. Step 2 will ask you
to enter a name for your weather station (get creative if you want, but don’t forget the name you
gave it!) and choose your station hardware (choose “other”). Once you complete this section,
click Submit to generate your unique Station ID and key.
5. Write down or screenshot your Station ID and Station Key/Password for reference and to
complete the setup process.
7
CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION
The console can upload weather data to WUnderground and / or Weathercloud through WI-FI
router, you can follow the step below to setup your device.
NOTE:
The Weather Underground and Weathercloud website are subjected to change without notice.
CREATE WEATHER UNDERGROUND ACCOUNT
1. In https://www.wunderground.com click the "Join" on the top right corner to open the
registration page. Follow the instructions to create your account.
NOTE:
Use the valid email address to register your account.
2. After you have created your account and completed the Email validation, please go back to
the WUndergound web page to login. Then, click “My Prole” button on the top to open the
drop-down menu and click "My Weather Station".
3. In "My Weather Station" page bottom, press the "Add New Device" button to add your
device.
4. Follow their instruction to enter your station information, in the Step "Tell Us More About
Your Device", (1) enter a Name for your weather station. (2) choose “Other” in “Device
Hardware” section and ll in other the other information (3) select "I Accept" to accept
Weather underground's privacy terms, (4) click “Next” to create your station ID and key.
(2)
(2)
(3)
(4)
(1)
7
CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION
The console can upload weather data to WUnderground and / or Weathercloud through WI-FI
router, you can follow the step below to setup your device.
NOTE:
The Weather Underground and Weathercloud website are subjected to change without notice.
CREATE WEATHER UNDERGROUND ACCOUNT
1. In https://www.wunderground.com click the "Join" on the top right corner to open the
registration page. Follow the instructions to create your account.
NOTE:
Use the valid email address to register your account.
2. After you have created your account and completed the Email validation, please go back to
the WUndergound web page to login. Then, click “My Prole” button on the top to open the
drop-down menu and click "My Weather Station".
3. In "My Weather Station" page bottom, press the "Add New Device" button to add your
device.
4. Follow their instruction to enter your station information, in the Step "Tell Us More About
Your Device", (1) enter a Name for your weather station. (2) choose “Other” in “Device
Hardware” section and ll in other the other information (3) select "I Accept" to accept
Weather underground's privacy terms, (4) click “Next” to create your station ID and key.
(2)
(2)
(3)
(4)
(1)

19
7
CREATE WEATHER SERVER ACCOUNT & SETUP WI-FI CONNECTION
The console can upload weather data to WUnderground and / or Weathercloud through WI-FI
router, you can follow the step below to setup your device.
NOTE:
The Weather Underground and Weathercloud website are subjected to change without notice.
CREATE WEATHER UNDERGROUND ACCOUNT
1. In https://www.wunderground.com click the "Join" on the top right corner to open the
registration page. Follow the instructions to create your account.
NOTE:
Use the valid email address to register your account.
2. After you have created your account and completed the Email validation, please go back to
the WUndergound web page to login. Then, click “My Prole” button on the top to open the
drop-down menu and click "My Weather Station".
3. In "My Weather Station" page bottom, press the "Add New Device" button to add your
device.
4. Follow their instruction to enter your station information, in the Step "Tell Us More About
Your Device", (1) enter a Name for your weather station. (2) choose “Other” in “Device
Hardware” section and ll in other the other information (3) select "I Accept" to accept
Weather underground's privacy terms, (4) click “Next” to create your station ID and key.
(2)
(2)
(3)
(4)
(1)
8
5. Jot down Your "Station ID" and "Station key" for the further setup step.
CREATE WEATHERCLOUD ACCOUNT
1. In https://weathercloud.net enter your information in "Join us today" section, then follow
the instructions to create your account.
NOTE:
Use the valid email address to register your account.
2. Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new
device.
CREATE YOUR WEATHERCLOUD ACCOUNT
1. Visit the Weathercloud website at https://www.weathercloud.net and enter your information in
the box that says Join Us Today. Follow the instructions to create an account.
NOTE: Please use a valid email address to register your account.
8
CREATE WEATHERCLOUD ACCOUNT
1. In https://weathercloud.net enter your information in "Join us today" section, then follow
the instructions to create your account.
NOTE:
Use the valid email address to register your account.
2. Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new
device.
3. Enter all the information in Create new device page, for the Model* selection box select
the "W100 Series" under "CCL" section. for the Link type* selection box select the "Pro
Weather Link", Once you have completed, click Create.

20
2. Once your account is created, sign into it, and then click +New to add a new device.
3. Enter all the requested information into the Create New Device page. When presented with the
Model selection box, choose LOWSC510SWB Series under the Logia section. When presented
with the Link Type selection box, choose Pro Weather Link. Once you have completed this
section, click Create.
4. Write down or screenshot your Weathercloud ID and Station Key/Password for reference and to
complete the setup process.
8
CREATE WEATHERCLOUD ACCOUNT
1. In https://weathercloud.net enter your information in "Join us today" section, then follow
the instructions to create your account.
NOTE:
Use the valid email address to register your account.
2. Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new
device.
3. Enter all the information in Create new device page, for the Model* selection box select
the "W100 Series" under "CCL" section. for the Link type* selection box select the "Pro
Weather Link", Once you have completed, click Create.
8
CREATE WEATHERCLOUD ACCOUNT
1. In https://weathercloud.net enter your information in "Join us today" section, then follow
the instructions to create your account.
NOTE:
Use the valid email address to register your account.
2. Sign in weathercloud and then you will go the "Devices" page, click "+ New" to create new
device.
3. Enter all the information in Create new device page, for the Model* selection box select
the "W100 Series" under "CCL" section. for the Link type* selection box select the "Pro
Weather Link", Once you have completed, click Create.
9
4. Jot down your ID and key for the further setup step.
SETUP WI-FI CONNECTION
1. When you rst power up the console, or press and hold the [ WI-FI / SENSOR ] key for 6
seconds in normal mode, the console LCD will show "AP" and " " icon to signify that it has
entered AP (access point) mode, and is ready for WI-FI settings.
2. Use the smart phone, tablet, or computer to connect to the console through WI-FI.
3. In PC choose WiFi network settings or In Android / iOS choose setting →WI-FI to select the
console’s SSID: PWS-XXXXXX in the list and it will need several second to connect.
PWS-XXXXXX
PWS-XXXXXX
PC WI-FI network interface Android WI-FI network interface
4. Once connected, enter the following IP address into your internet browser’s address bar, to
access the console’s web interface:
http://192.168.1.1
NOTE :
- Some browsers will treat 192.168.1.1 as a search, so make sure you include http:// header.
- Recommended browsers, such as the latest version of Chrome, Safari, Edge, Firefox or
Opera.