LOGICDATA HSF User manual

Manual
HSF
Cablehandset
LOGICDATA Electronic & Software GmbH
Hinterleitenstrasse 22a
A 8523 Frauental /Austria
Version: 1
Availability and specifications are subject to change without prior notice. LOGICDATA assumes no
liability for maloperation or improper use of products. LOGICDATA will at point of delivery
replace/repair defective products covered by the warranty. No liability is assumed beyond such
replacement/repair. Please contact LOGICDATA directly on inquiries or custom requirements.
© 2006 LOGICDATA

HSF - cablehandset
Seite 2/15
Contents
1. PREFACE.....................................................................................3
2. GENERAL....................................................................................3
2.1. INTENDED USE..........................................................................3
2.2. FUNCTIONALITY HSF ...............................................................4
2.3. PACKAGE CONTENTS................................................................4
2.4. OVERVIEW ................................................................................6
2.5. DISPLAY OVERVIEW .................................................................6
2.6. HANDSET PLUG.........................................................................7
3. MOUNTING INSTRUCTIONS..................................................8
4. FUNCTIONS ................................................................................9
4.1. DISPLAY....................................................................................9
4.2. INFORMATION -LED’S.............................................................9
4.3. BASIC FUNCTIONS...................................................................10
4.4. ADVANCED FUNCTIONS..........................................................11
4.5. TECHNICAL DATA...................................................................13
5. APPENDIX .................................................................................14
5.1. POSSIBLE ERRORS AND SOLUTIONS........................................14
5.2. CONTINUATIVE INFORMATION ...............................................15
6. MANUFACTURER’S DATA....................................................15

HSF - cablehandset
1. Preface
Dear customer,
Thank you for choosing a HSF - Cablehandset by LOGICDATA GmbH. You have
purchased a state-of-the-art product.
2. General
2.1. Intended Use
The HSF - Cablehandset must solely be uses with LOGICDATA control boxes. The
control box must be installed, initially operated and functional tested by competent
personnel only. Use other than described above is only allowed with permission of
LOGICDATA.
Information: For all information concerning LOGICDATA control boxes
pleas refer to the applicable manual.
2.2. Definition
Information: For definitions and information concerning LOGICDATA
Control boxes please refer to the applicable manual.
Aside of moving your table up and down your LOGICDATA control box is able to
carry out other functions, like controlling the brightness of a lamp or a monitor –
height adjustment. This function is called second motorgroup.
Seite 3/15

HSF - cablehandset
Seite 4/15
2.3. Functionality HSF
The HSF - Cablehandset offers following functionality:
•Ultra - flat design
•Big and comfortable to use buttons
•New info display with status information
•Display of 1/10 inch or cm
•soft click button feeling
•shift mechanism under table plate
•Easy and fast underside mounting (screws are included)
2.4. Package Contents
The HSF - Cablehandset package contains:

HSF - cablehandset
Seite 5/15
Pict. 1 – package content
cHSF - cablehandset
dmounting plate
escrews
Danger: Use only genuine replacement parts! Repairs must be carried
out only by a qualified service technician! If you neglect to do so you
void your warranty!

HSF - cablehandset
2.5. Overview
desk / 2nd motorgroup
upwards
desk / 2nd motorgroup
downwards
position button 1
position button 4
position button 2
position button 3 desk downwards
desk upwards
memory button
2.6. Display Overview
Seite 6/15
Containerstop LED Ergotrainer LED
Reset LED Info LED
Flex Function LED Pincode LED

HSF - cablehandset
2.7. Handset Plug
Pin assignment
321
54
76
Handset plug (DIN 45329)
front view
1......... HS1 5…...... HS4
2......... HS3 6.......... +5V
3......... n.c. 7........... SER_OUT
4......... HS2 SHELL.. GND
n.c. …… not connected
Caution
Caution: The HSF handset is only suitable for LOGICDATA motor
controls.
To prevent damage of the unit, take care not to interchange handset and
motor sockets.
Color code: handset ... blue motor ... black
Seite 7/15

HSF - cablehandset
3. Mounting Instructions
ount the HSF - cablehandset underside your desktop in an appropriate position.
•1 screw driver
lease take note, that the handset is equipped with a shift mechanism. Therefore
1) Unpack the handset.
M
Following tools are required for installation:
P
always mount the handset in a drawn in position.
Note: Dispose of the packaging material ecologically sound (separate
plastic foil and cardboard)!
2) Place the handset on the underside of your desktop on the position of choice.
3) Fix the mounting plate with the 6 enclosed screws.
4) Connect the handset to the control box using the jack marked with
Note that the handset should be reached comfortably. Its front side should not
protrude over the table’s edge.
(DIN
45329, 7 – pin) only! Do not connect the handset plug to the motor jacks!!
Caution: Unplug the power cord while mounting the LogicS control box!
Pict. 2 – Connect the HSF - cablehandset to the control box (e.g. LOGIC S)
Seite 8/15

HSF - cablehandset
4. Functions
andset is capable of a wide range of functions, which are
escribed below.
4.1. Display
The HSF – cablehandset’s display consists of a 3 digit position and information
isplay and 6 lateral information LED’s.
The HSF – cableh
d
d
4.2. Information - LED’s
Contain r –
at the Containerstop function is active.
s that the control box is being reseted.
ws that the Flex Function is active.
the Ergotrainer is active.
arns you of an important information on the position and information
isplay.
ows that the Pincode function is active.
Note: Please refer to your control box manual for further information
regarding the functions mentioned below
e LED
This LED shows th
Reset – LED
This LED show
Flex – LED
This LED sho
.
Ergotrainer – LED
This LED shows that
Info – LED
This LED w
d
PIN – LED
This LED sh
Seite 9/15

HSF - cablehandset
4.3. Basic Functions
unction Description Note
Note: In case of no motorg
buttons (motorgroup 2 upwardroup 2 attached the therefore assigned s / motorgroup 2 downwards) are used for
the desk upwards / desk downwards functions.
F
Desk upwards
For an upward adjustment of
the desk push this button.
has
The desk will continue driving
upwards until you release the
Push this button until the
desired height of the desk
been reached.
button, or the maximum height
is reached.
Seite 10/15
Desk downwards
For a downward adjustment of
the desk push this button.
has
The desk will continue driving
downwards until you release
Push this button until the
desired height of the desk
been reached.
the button, or the minimum
height is reached.
Motorgroup 2 /
Desk upwards
For an upward adjustment of
the motorgroup 2 (e.g. monitor
eight of the desk has
n is used for
ue
riving upwards until you
adjustment) or desk, push this
button.
Push this button until the
desired h
been reached.
In case of no motorgroup 2
attached this butto
the Desk upwards function.
Motorgroup 2 will contin
d
release the button, or the
maximum height is reached.
Motorgroup 2 /
Desk downwards
For a downward adjustment of
e motorgroup 2 (e.g. monitor
eight of the desk has
for
riving downwards until you
th
adjustment) or desk, push this
button.
Push this button until the
desired h
been reached.
In case of no motorgroup 2
attached this button is used
the Desk downwards function.
Motorgroup 2 will continue
d
release the button, or the
minimum height is reached.

HSF - cablehandset
4.4. Advanced Functions
4.4.1. Storing a position
Using this function you are able to store a desk-height.
Note: On initial operation all stored positions are equal to the lowest
possible desk-height (lower end position).
Note: Only one desk-height per button is allowed.
1. Move the desk to the position you want to store.
The display reads the actual height of the desk (e.g. 73cm).
2. Press the S button.
The display reads S –.
3. Press the position button of choice (e.g. S2).
The display reads S 2.
4. Now the height is stored on the chosen position button.
The saving operation is confirmed with a double-click sound and after
appr. 2 seconds the stored height will be displayed.
Seite 11/15

HSF - cablehandset
4.4.2.Recalling a stored position
Using this function you are able to recall a stored position.
Alternative A (manually)
1. Press and hold the desired position button (e.g. 2).
The desk moves until the saved position is reached.
If you release the button before reaching the saved position, the desk
stops and the saved position will not be reached.
2. The desk has reached the saved height. Release the position button
The display reads the actual desk-height.
Alternative B (using double click automatic function)
Note: If the double click function is available depends on the
configuration of your control box.
1. Double-click the desired position button (e.g. 2)
2. The desk automatically moves to the saved position.
If you press any button before reaching the saved position, the desk
stops and the saved position will not be reached.
The display reads the actual desk-height.
Seite 12/15

HSF - cablehandset
Seite 13/15
4.5. Technical Data
Supply voltage 5V DC
Current consumption 75 mA
Life cycle (switching cycles) 10. 000
Ambient temperature 0 – 40° C
Cable length 2070 mm
Measures (l, w, h) 141mm x 129,1 mm x 9,6mm
Weight 0,13 kg (incl. Cable)

HSF - cablehandset
5. Appendix
5.1. Possible Errors and Solutions
This chapter offers detailed information on possible troubles and solutions:
Display does not work (buttons work)
Possible Cause Solution
Cable is defect Contact our customer service
Display is defect Contact our customer service / change the
handset
Mikrocontroller is defect Contact our customer service / change the
handset
Handset is defect Contact our customer service / change the
handset
Buttons do not work (display works)
Possible Cause Solution
Cable is defect Contact our customer service
Handset is defect Contact our customer service / change the
handset
Handset does not work (neither display nor buttons)
Possible Cause Solution
Cable is not plugged
Cable is not plugged as intended
Plug the plug in the intended jack marked
with (DIN 45329, 7 – polig).
Bad pin contact Plug off the plug an plug it in as intended ( as
described above)
Cable is defect Contact our customer service
Seite 14/15

HSF - cablehandset
5.2. Continuative Information
Final Disposal
Please heed following disposal instructions when disposing of the HSF -
cablehandset:
Note: Dispose of the components ecologically sound (separate plastic
from electronics parts)!
6. Manufacturer’s Data
LOGICDATA
Electronic & Software Development GmbH
Hinterleitenstrasse 22a
A-8523 Frauental - Austria
Tel.: [phone]
Fax: [phone]
Email: [email protected]
http://www.logicdata.at
Seite 15/15