Logicor 1001 User manual

Version / Issue Date: 12 Mar 2014
Clear Heater System
Control Panel User Guide
Logicor (CH) Ltd.

i
TABLE OF CONTENTS
INTRODUCTION ....................................................................................................1
Control Panel.....................................................................................2
Clear Heater Units.............................................................................3
SECTION 1: HELP MODE .......................................................................................4
Help Mode .........................................................................................5
SECTION 2: CONTROL PANEL & TEMPERATURE SETTINGS ...................................6
Control Panel & Temperature Settings .........................................7
Main Settings......................................................................................8
oWifi Settings ..............................................................................9
oTime & Date ...........................................................................10
oTariff Settings ..........................................................................11
oUnits of Measurement ..........................................................12
oScreen Options......................................................................13
Status Screen Options: Choose a System .........14
Status Screen Options: Choose Readings.........15
Brightness Settings..................................................16
Recalibration ..........................................................17
Fireguard Settings...................................................18

ii
Load Original Settings ....................................................................19
Clear Heater System Settings .......................................................20
oAdjust Complete System .....................................................21
oAdjust Zones ...........................................................................22
Edit Zone Name & Temperature .........................23
Add New Zone .......................................................24
Assign Heater Units to Zone..................................25
Delete Zone.............................................................26
oAdjust Heaters........................................................................27
Add New Heater....................................................28
Add New Heater: Waiting....................................29
Add New Heater: Confirmation..........................30
Edit Heater Name & Temperature......................31
Delete Heater Unit .................................................32
oLink Heaters ............................................................................33
Edit Name & Temperature of Link.......................34
Add New Link..........................................................35
Modify Link...............................................................36
Delete Link ...............................................................37

iii
Heat-up Mode.................................................................................38
Heater Surface Temperature .......................................................39
SECTION 3: STATUS SCREEN...............................................................................40
Status Screen ...................................................................................41
SECTION 4: COST & ENERGY SETTINGS .............................................................42
Cost & Energy Settings...................................................................43
Adjust Cost & Energy Settings.......................................................44
SECTION 5: TIMER SETTINGS...............................................................................45
Timer Settings ...................................................................................46
oWeekly Settings......................................................................47
Add Event................................................................48
Adjust Event ............................................................49
oGraphical View .....................................................................50
oEnable / Disable Scheduling ..............................................51
SPECIFICATION: CONTROL PANEL ....................................................................52
SPECIFICATION: CLEAR HEATER UNITS ..............................................................53

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 1
MENU ►Tip! Use the menu path headings at the top of each page to help you navigate through the screens
Introduction
Energy efficiency has never been more important,
especially where cost is concerned. With our smart
touch-screen control panel you will benefit from better,
more accessible information and control over your
heating costs.
To get started, simply plug in your control panel and
Clear Heater units. The system is pre-programmed and
ready to go but you can follow the on-screen prompts
and this user guide to customise your settings.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………........................ (Page 40)
Section 4:
Cost & Energy Settings…....................... (Page 42)
Section 5:
Timer Settings……………....................... (Page 45)
How to use this guide
This user guide is designed to help you get the most from
your Clear Heater System and understand the different
functions available on the control panel.
Your control panel also has help messages associated
with each function; simply press the help icon at any
time.
Use the table of contents at the beginning of this guide
to find the page number of the function you need help
with and go to that page.
The nature of the control panel options means that you
may need to back-track through the screen menus in
order to fully understand how to reach your chosen
function.
Use the MENU ►headings at the top of each page to
find the page number of each previous screen leading
up to your chosen function.
If you are using an electronic (pdf) copy of this guide
you can click any page number reference or
MENU ►heading at the top of the page to go direct to
that page.
Check out our website www.clear-heater.co.uk for
product updates.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 2
MENU ►Tip! Use the menu path headings at the top of each page to help you navigate through the screens
Control Panel
The control panel is the ‘brain’ of the Clear Heater
System and is recommended by the Energy Saving Trust
for its energy saving abilities.
Simply plug in your control panel and Clear Heater units
to the wall socket and they are ready to communicate
with each other using the electrical mains wiring in your
home.
The control panel is also equipped with Wifi capability to
receive software updates via the internet. A new feature
to be launched in 2014 will be the ability to connect via
your Smartphone or iPad.
The control panel is pre-programmed to work out of the
box but you can change the settings at any time with
your own preferences.
For example, you can change the name and
temperature of each heater unit, link heater units to work
as one unit together, or assign heater units to work in
named zones (e.g. all bedrooms).
Use the touch screen LCD to select options or type in
your data. The menu icons on the left of the display are
your starting point for each of the following sections.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………........................ (Page 40)
Section 4:
Cost & Energy Settings…....................... (Page 42)
Section 5:
Timer Settings……………....................... (Page 45)

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 3
MENU ►Tip! Use the menu path headings at the top of each page to help you navigate through the screens
Clear Heater Units
Our unique patented infrared heaters require no
complex plumbing or wiring. You just fit them to the wall,
plug in to an electric wall socket and let the intelligent
control panel do the hard work for you.
The Clear Heating System is an all-electric phased
radiant heating system. The heaters have a very thin
carbon ceramic heating element sandwiched between
two sheets of toughened glass with a mica insert to
minimise rear facing heat loss.
We pride ourselves in making robust products that are
both elegant in design and provide solutions that work.
We are so confident in our heater system that we give
you 20 years guarantee on all heater units with a life
expectancy of over 33 years.
Important:
A Clear Heater System requires a control panel to
operate normally. Each Clear Heater unit has a
manual temperature control on the base panel. This is
only active if the heater is not connected to its control
panel and then only for a
limited period of up to
eleven days before it stops
working. The heater unit will
operate again once a
control panel is connected.
Clear Heaters are robust and durable but please
avoid impacts from sharp or heavy objects: a hammer
for example;
Use a clean dry cloth to clean the heaters and control
panel but avoid polish, sprays or harsh abrasives;
Warning! The temperature sensor is designed to cope
with normal household dust. Please avoid spraying
polish, hair sprays or other chemical sprays near the
sensor as it may reduce or damage the performance;
Caution! Clear Heaters operate at a normal 70°C
(158 °F). Please be careful when heating in the vicinity
of young or vulnerable people.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 4
MENU ►Help Icon
Section 1: Help Mode
Select the Help Icon on your control panel display then turn to page 5.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………........................ (Page 40)
Section 4:
Cost & Energy Settings…....................... (Page 42)
Section 5:
Timer Settings……………....................... (Page 45)

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 5
MENU ►Help Icon
Help Mode
The help icon is always there at the top left of your
screen to give you additional information about the
current control panel display.
This gives you an overview of your current screen (which
is non selectable), and a descriptive help message at
the top of the screen.
Pressing ‘Exit Help’ takes you back to your original
screen.
Options:
Press ‘Help’Icon
Touch the help icon at any time to enter help mode.
Read the descriptive help message at the top of the
screen.
Press ‘Exit’Help
Pressing ‘Exit Help’ takes you back to your original
screen from where you can continue with your
choices.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 6
MENU ►Temperature Icon
Section 2: Control Panel & Temperature Settings
Select the Temperature Icon on your control panel display then turn to page 7.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………........................ (Page 40)
Section 4:
Cost & Energy Settings…....................... (Page 42)
Section 5:
Timer Settings……………....................... (Page 45)

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 7
MENU ►Temperature Icon
Control Panel & Temperature Settings
Selecting the Temperature Icon brings you to the main
control panel and temperature settings menu.
From here you can either change the main settings to
set up your control panel or organize all your heating
temperature settings to your own preferences.
Loading the original factory settings will reset the control
panel completely and delete all your preferences.
Options:
Main settings (Page 8)
Adjust the main settings of the control panel, including
Wifi, time and date, tariff settings, units of
measurement, screen display options and the
fireguard function settings.
Load original settings (Page 19)
Load the original factory settings if you want to reset
the system back to its factory settings. You will be
asked to confirm your choice on the next screen or
cancel.
Clear Heater System (Page 20)
Adjust your heating preferences for individual heater
units, create heating zones, or link heater units
together to operate as one.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 8
MENU ►Temperature Icon (p. 7) / Main settings
Main Settings
Set up your control panel preferences by choosing one
of the displayed options, or click the back arrow button
to go back to the previous menu.
Options:
Wifi settings (Page 9)
Amend your Wifi settings to enable the control panel
to connect to the internet for software updates or
access your control panel via your Smartphone.
Time & date (Page 10)
The time and date is needed for the control panel to
accurately regulate your heater system and provide
you with up to date performance and cost data.
Tariff settings (Page 11)
Enter your tariff rate to get accurate cost and
performance data for your system.
Units of measurement (Page 12)
Select your preferred choice of currency for your cost
performance targets
Screen options (Page 13)
Edit which status messages appear on the main status
screen or change the control panel screen brightness
levels and touch-screen settings.
Fireguard (Page 18)
Fireguard warns you if a heater unit detects a higher
than expected temperature in the room.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 9
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Wifi settings
Wifi Settings
Amend your Wifi settings to enable your control panel to
connect to the internet for software updates. A
Smartphone can also function as a Wifi Hotspot.
Connecting to the internet also allows you to access
your control panel via your Smartphone.
Use the keypads to type in your settings and press the
save button to store your settings.
The INFO message displays the current Wifi status.
Options:
Manual setup
Enter your network name or SSID (service set identifier)
and password to add your Wifi network to the control
panel. Use the keypads to type in your settings and
press the save button to store your settings.
Connect to an available network
Choose from the list of available networks and touch
once to connect or unselect by touching the screen
option again.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 10
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Time & Date
Time & Date
The time and date is needed for the control panel to
accurately regulate your heater system and provide you
with up to date performance and cost data.
Once set, you should not need to adjust the time and
date again if your control panel is connected to the
internet. Time and date updates will then be automatic.
Options:
Enter time
Enter the current time by first selecting the area on the
screen.
The time format is Hours: Minutes: Seconds
Use the keypads to type in your settings and press the
save button to store your settings.
Enter date
Enter the current date by selecting the area on the
screen.
The date format is Day / Month / Year.
Use the keypads to type in your settings and press the
save button to store your settings.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 11
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Tariff settings
Tariff Settings
Entering your electricity tariff allows accurate cost and
performance data feedback for your system.
Your tariff settings can be found on your utilities bill, or by
contacting your service provider.
Please remember to amend your tariff rate on the
control panel if and when your tariff changes.
Options:
Enter your electricity tariff
Enter your electricity tariff by first selecting the area on
the screen. Use the keypads to type in your settings
and press the save button to store your settings.
Tip:
15p is entered as 0.1500 GBP
20p is entered as 0.2000 GBP

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 12
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Units of measurement
Units of Measurement
The currency and temperature units are required to
display your cost performance targets and the system
temperature. You can change your preferred units from
the available options.
Options:
Enter preferred currency
Choose from the list of available currencies.
Touch once to select or again to unselect.
Selected units will display a tick next to the item.
Press the save button to store your entry.
Enter preferred temperature units
Choose to display temperature in degrees Fahrenheit
or degrees Celsius.
Touch once to select or again to unselect.
Selected units will display a tick next to the item.
Press the save button to store your entry.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 13
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Screen options
Screen Options
Screen options allow you to change how your control
panel looks and adjust your touch-screen settings.
Choose which performance data appears on the main
status screen by selecting ‘Status screen options’.
Change the screen brightness and energy saving
settings by selecting ‘Brightness settings’.
Touch recalibration allows you to fine tune the touch-
screen sensitivity settings.
Options:
Status Screen Options (Page 14)
Choose which performance data appears on the
main status screen.
Brightness Settings (Page 16)
Change the screen and LED brightness levels, or adjust
the how long the screen stays on before switching into
energy saving mode.
Touch Recalibration (Page 17)
Touch recalibration adjusts the control panel sensitivity
settings.
Choose this option to start the recalibration process
where you’ll be asked to touch a white dot at the top-
left, bottom-right and middle of the screen to
automatically calibrate the screen.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 14
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Screen options (p.13) / Status screen options
Status Screen Options: Choose a System
You can choose which performance data appears on
the main status screen. First choose your heater system
from the list. If you only have one heater system
available only one option will be listed.
Additional systems are proposed for the future that will
be listed on this screen if available. Please check our
website for product updates.
Options:
Choose Clear Heater System (Page 15)
Choose this option to adjust the performance data
readings for your Clear Heater System.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 15
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Screen options (p.13) / Status screen options (p.14) / CHS
Status Screen Options: Choose Readings
You can choose which performance data readings
appear on the main status screen by selecting from the
list of options.
Once your choice is selected it will display a tick next to
the item and will be displayed on the main status screen.
The status screen is reached by pressing the ‘Home’
Icon.
Options:
Choose your readings
Choose from the list which performance data
readings appear on the main status screen.
Touch once to select or again to unselect. Selected
items will display a tick next to the item.
Scroll up and down the list with the arrows.
Press the save button to store your entry.

© 2014 Logicor (CH) Ltd clear-heater.co.uk Page 16
MENU ►Temperature Icon (p. 7) / Main settings (p.8) / Screen options (p.13) / Brightness settings
Brightness Settings
The display brightness option is the backlight brightness
level of the main LCD display screen.
The control panel has three blue LEDs that switch on
when the control panel goes into sleep mode.
Sleep mode is the energy saving function of the control
panel. In sleep mode the main display screen dims to
black. You can change how long (in seconds) the
display is active before switching off into sleep mode.
Options:
Edit display brightness level
Touch the plus and minus symbols to increase or
decrease the brightness setting between 1 and 10.
Press the save button to store your entry.
Edit LED brightness level
Touch the plus and minus symbols to increase or
decrease the LED brightness setting between 1 and
10.
Press the save button to store your entry.
Change ‘display off time’ duration
The ‘display off time’ function switches the screen
display into energy saving mode after a
predetermined time.
Touch the plus and minus symbols to increase or
decrease the display off time setting between 1 and
300 seconds (5 minutes).
Press the save button to store your entry.