Logicor PSU 1001 User manual

Version: EN-UK-01-02-2016
Language: English
Control Panel User Guide
Logicor (CH) Ltd

TABLE OF CONTENTS
i
SAFETY............................................................................................................................................................... V
SÉCURITÉ ......................................................................................................................................................... VII
SEGURIDAD .......................................................................................................................................................IX
INTRODUCTION ..................................................................................................................................................1
CONTROL PANEL ................................................................................................................................................2
CLEAR HEATER UNITS ..........................................................................................................................................3
SECTION 1: HELP MODE ......................................................................................................................................4
HELP MODE......................................................................................................................................................5
SECTION 2: CONTROL PANEL & TEMPERATURE SETTINGS ...................................................................................6
CONTROL PANEL &TEMPERATURE SETTINGS.............................................................................................................7
MAIN SETTINGS ......................................................................................................................................................8
Wifi Settings........................................................................................................................................................................... 9
Time & Date ......................................................................................................................................................................... 10
Tariff Settings....................................................................................................................................................................... 11
Country Select...................................................................................................................................................................... 12
Screen Options..................................................................................................................................................................... 13

TABLE OF CONTENTS
ii
oStatus Screen Options: Choose a System ................................................................................................................ 14
oStatus Screen Options: Choose Readings ................................................................................................................ 15
oBrightness Settings .................................................................................................................................................. 16
oBrightness Settings - Heater Communication Light................................................................................................. 17
oRecalibration............................................................................................................................................................ 18
Frost & Fireguard Settings ................................................................................................................................................... 19
LOAD ORIGINAL SETTINGS .......................................................................................................................................20
CLEAR HEATER SYSTEM SETTINGS..............................................................................................................................21
Adjust Complete System...................................................................................................................................................... 22
Adjust Zones......................................................................................................................................................................... 23
oAdjust Independent Zone ........................................................................................................................................ 24
oIndependent Zone Switched ON.............................................................................................................................. 25
oEdit Zone Name & Temperature.............................................................................................................................. 26
oAdd New Zone.......................................................................................................................................................... 27
oAssign Heater Units to Zone .................................................................................................................................... 28
oDelete Zone.............................................................................................................................................................. 29
Adjust Heaters ..................................................................................................................................................................... 30
oAdd New Heater....................................................................................................................................................... 31
oAdd New Heater: Waiting........................................................................................................................................ 32
oAdd New Heater: Confirmation ............................................................................................................................... 33
oEdit Heater Name & Temperature........................................................................................................................... 34
oDelete Heater Unit................................................................................................................................................... 35

TABLE OF CONTENTS
iii
Link Heaters ......................................................................................................................................................................... 36
oEdit Name & Temperature of Link........................................................................................................................... 37
oAdd New Link ........................................................................................................................................................... 38
oModify Link .............................................................................................................................................................. 39
oDelete Link ............................................................................................................................................................... 40
Adjust Heat-up Mode .......................................................................................................................................................... 41
oHeat-up Mode - Adjust Surface Temperature......................................................................................................... 42
oHeat-up Mode - Adjust Activation Threshold.......................................................................................................... 43
Heat-up Mode Override - Activation ................................................................................................................................... 44
oHeat-Up Mode Override - Deactivate...................................................................................................................... 45
Heater Surface Temperature............................................................................................................................................... 46
CLEAR HEATER CLOTHES DRYER ................................................................................................................................47
Select Clear Heater .............................................................................................................................................................. 48
Adjust Drying Time............................................................................................................................................................... 49
Start Drying .......................................................................................................................................................................... 50
INLINE HOT WATER SYSTEM SETTINGS .......................................................................................................................51
RESTRICTED MODE OFF ..........................................................................................................................................52
SECTION 3: STATUS SCREEN ..............................................................................................................................53
STATUS SCREEN ...............................................................................................................................................54

TABLE OF CONTENTS
iv
SECTION 4: COST & ENERGY SETTINGS..............................................................................................................55
COST &ENERGY SETTINGS..................................................................................................................................56
ADJUST COST &ENERGY SETTINGS ............................................................................................................................57
SECTION 5: TIMER SETTINGS.............................................................................................................................58
TIMER SETTINGS ..............................................................................................................................................59
WEEKLY SETTINGS .................................................................................................................................................60
Add Event............................................................................................................................................................................. 61
Adjust Event......................................................................................................................................................................... 62
GRAPHICAL VIEW ..................................................................................................................................................63
ENABLE /DISABLE SCHEDULING ................................................................................................................................64
SPECIFICATION: CONTROL PANEL .....................................................................................................................65
SPECIFICATION: CLEAR HEATER UNITS ..............................................................................................................66
GH -518R (LARGE HEATER UNIT)............................................................................................................................68
GH -518B (SMALL HEATER UNIT) ...........................................................................................................................69
GH -518P (PORTRAIT HEATER UNIT) .......................................................................................................................70
GH -518C (CONSERVATORY HEATER UNIT) ...............................................................................................................71

v
Safety
(English - Part 1 of 2)
Installation
The Clear Heater System must be installed by a
certified installer authorized by Logicor.
Our installers have to pass strict qualification standards
before they become approved to install our systems.
Our installers will advise and install your Clear Heater
System in the most effective position to heat your
property safely and efficiently.
WARNING - Clear Heater units must not be located
immediately below a wall socket outlet.
WARNING - Bathroom Installations.
Do not install the control panel or standard heater unit
in a bathroom or wet room situation. For placement of
heaters in wet room situations we offer a special order
item IP53 rated heater. A qualified installer and
surveyor will advise if you need this type of unit.
Clear Heaters units and control panels located in a
bathroom must be positioned so that switches and
other controls cannot be touched by a person in the
bath or shower.
Heater units must not be installed at a height greater
than 1.8m in a bathroom.
WARNING - Do not install the Clear Heater System in a
wardrobe or to a ceiling.
Our installers will advise and install your Clear Heater
System in the most effective position to heat your
property safely and efficiently.
Safety & Maintenance
WARNING - A heater units must not be used if the glass
panels are damaged.
Clear Heaters are robust and durable but please
avoid impacts from sharp or heavy objects: a hammer
for example. In the unlikely event that a glass panel of
your clear heater unit becomes damaged, unplug the
heater unit from the wall socket if it is safe to do so
and contact Logicor (CH) Ltd.
CAUTION - Some parts of this product can become hot
and cause burns. Particular attention has to be given
where children or vulnerable people are present.
Clear Heaters operate at approximately 70°C (158 °F)
but can run in excess of that temperature if set to do
so.
The use of this heater by young children under 8 years
old, by infirm persons or persons with reduced
physical, sensory or mental capabilities, or by persons
with a lack of experience and knowledge without
supervision is not recommended. Do not allow young
children to play with the appliance.
Children of less than 3 years should be kept away
unless continuously supervised.
WARNING - Do not dismantle; this appliance contains
no user serviceable parts.
In the unlikely event of you requiring service please
contact your authorised distributor or Logicor by
visiting www.logicor.co.uk.

vi
Safety
(English - Part 2 of 2)
Safety & Maintenance (continued)
WARNING - If the power cord is damaged do not use
the appliance.
If the power cord is damaged it must be replaced by
the manufacturer, its service agent or similar qualified
persons to avoid a hazard.
WARNING - In order to avoid overheating, do not
cover the heater.
If you wish to dry clothes with the Clear Heater System
please purchase a clothes dryer system from Logicor.
The Logicor clothes dryer system provides a
convenient, safe and quick method to dry clothes
positioned a safe distance from the heater unit. At no
point must clothing be hung directly over a Clear
Heater unit.
WARNING: Do not cover.
Additional Warnings & Recommendations:
For Indoor use only.
Do not use with an extension socket.
Do not hang on or place weight on the heater units.
Check the cordset and routing regularly for damage.
If damaged disconnect from system.
Heater units to be mounted in vertical and horizontal
orientation only.
Do not install near or place combustible materials in
the immediate vicinity of a heater unit.
Cleaning
IMPORTANT - The temperature sensor located in the
Heater unit base is designed to cope with normal
household dust. Please avoid spraying polish, hair
sprays or other chemical sprays near the sensor as it
may reduce or damage the performance. Use a
clean dry cloth to clean the heaters and control
panel but avoid polish, sprays or harsh abrasives.
IMPORTANT - Cleaning and user maintenance shall not
be made by children.

vii
Sécurité
(français - partie 1 sur 2)
Installation
Le Clear Heater System doit être installé par un
installateur certifié agréé par Logicor.
Nos installateurs doivent répondre à des standards de
qualification stricts avant d'être agréés pour
l'installation de nos systèmes. Nos installateurs vous
conseillerons et installerons votre Clear Heater System
à l'endroit le plus efficace pour chauffer votre
propriété efficacement en toute sécurité.
AVERTISSEMENT - Les radiateurs Clear Heater ne
doivent pas être installés directement sous une prise
de courant murale.
AVERTISSEMENT - Installations dans les salles de bain.
Ne pas installer le panneau de contrôle ou unité de
chauffage standard dans une salle de bain ou de la
situation de la chambre humide. Pour la pose des
radiateurs dans les situations de pièces humides, nous
offrons un poste de commande IP53 chauffe
nominale spéciale. Un installateur qualifié et arpenteur
conseillera si vous avez besoin de ce type d'unité.
Les radiateurs et les panneaux de contrôle Clear
Heater situés dans une salle de bain doivent être
positionnés de façon à ce que les interrupteurs et les
autres commandes ne puissent pas être touchés par
une personne se trouvant dans la baignoire ou dans la
douche. Les radiateurs Clear Heater ne doivent pas
être installés à une hauteur supérieure à 1,8 m dans
une salle de bain.
AVERTISSEMENT - N'installez pas le Clear Heater
System dans une penderie ou au plafond.
Nos installateurs vous conseillerons et installerons votre
Clear Heater System à l'endroit le plus efficace pour
chauffer votre propriété efficacement en toute
sécurité.
Sécurité & Entretien
AVERTISSEMENT - Un radiateur ne doit pas être utilisé si
les panneaux en verre sont endommagés.
Les Clear Heaters sont robustes et durables mais vous
devez éviter les chocs avec des objets pointus ou
lourds : un marteau par exemple. Dans le cas peu
probable où un panneau en verre de votre radiateur
Clear Heater serait endommagé, débranchez le
radiateur de la prise murale si cela peut être fait sans
danger, et contactez Logicor (CH) Ltd.
ATTENTION - Certaines parties de ce produit peuvent
devenir chaudes et causer des brûlures. Une
surveillance particulière est nécessaire en présence
d'enfants ou de personnes vulnérables.
Les Clear Heaters fonctionnent à une température
normale de 70 °C (158 °F). L'utilisation de ce radiateur
par les jeunes enfants de moins de 8 ans, par les
personnes infirmes ou les personnes ayant de faibles
capacités physiques, mentales ou sensorielles, ou par
des personnes manquant d'expérience et de
compétences sans surveillance n'est pas
recommandée. Ne laissez pas les enfants en bas âge
jouer avec l'appareil.
Enfants de moins de 3 ans doivent être tenus à l'écart
moins d'être surveillées en permanence.

viii
Sécurité
(français - partie 2 sur 2)
Sécurité & Entretien (suite)
AVERTISSEMENT - Ne pas démonter ; cet appareil ne
contient aucune pièce réparable par l'utilisateur.
Dans le cas peu probable où vous auriez besoin d'un
service technique, veuillez contacter votre distributeur
agréé ou Logicor en visitant www.logicor.co.uk.
AVERTISSEMENT - N'utilisez pas l'appareil si le cordon
électrique est endommagé.
Si le cordon électrique est endommagé, il doit être
remplacé par son fabricant, son agent de
maintenance ou une personne qualifiée apparentée
pour éviter un danger.
AVERTISSEMENT - Pour éviter la surchauffe, ne couvrez
pas le radiateur.
Si vous souhaitez sécher des vêtements avec le Clear
Heater System veuillez acheter un système de séchoir
à linge auprès de Logicor. Le système de séchoir à
linge Logicor offre un moyen pratique, sécurisé et
rapide de sécher des vêtements positionnés à une
distance sécuritaire du radiateur. En aucun cas les
vêtements ne doivent être suspendus directement au-
dessus d'un radiateur Clear Heater.
AVERTISSEMENT : Ne pas couvrir.
Avertissements et recommandations supplémentaires:
Pour une utilisation en intérieur uniquement.
Ne pas utiliser avec une prise d'extension.
Ne pas accrocher ou placer le poids sur les unités de
chauffage.
Vérifiez le cordon et le routage régulièrement pour les
dommages. Si endommagé déconnecter de système.
unités de chauffage pour être montés en position
verticale et horizontale.
Ne pas installer près ou de placer des matériaux
combustibles dans le voisinage immédiat d'une unité
de chauffage.
Nettoyage
IMPORTANT - Le capteur de température situé dans la
base du radiateur est conçu pour fonctionner en
présence de poussière domestique normale. Veuillez
éviter de vaporiser du vernis, de la laque à cheveux
ou d'autres produits chimiques en aérosol à proximité
du capteur car cela pourrait réduire ou dégrader la
performance. Utilisez un chiffon sec pour nettoyer les
radiateurs et le panneau de contrôle, mais évitez le
vernis, les vaporisateurs ou les abrasifs agressifs.
IMPORTANT - Nettoyage et entretien de l'utilisateur ne
sont pas fabriqués par des enfants.

ix
Seguridad
(Español - parte 1 de 2)
Instalación
Clear Heater System debe ser instalado por un
técnico certificado autorizado por Logicor.
Nuestros técnicos deben someterse a unas estrictas
normas de calidad antes de ser aptos para instalar
nuestros sistemas. Nuestros técnicos le aconsejarán e
instalarán su Clear Heater System en la posición más
efectiva para calentar su hogar de forma segura y
eficaz.
ADVERTENCIA –Las unidades de Clear Heater no
deben colocarse justo debajo de un enchufe de
pared.
ADVERTENCIA –Instalaciones en los baños.
No instale el panel de control o unidad de
calefacción estándar en el baño ni en situación
cuarto húmedo. Para la colocación de los
calentadores en situaciones habitaciones húmedas
ofrecemos un calentador especial clasificar posición
de pedido IP53. Un instalador y topógrafo cualificado
le aconsejará si necesita este tipo de unidad.
Los dispositivos Clear Heater y paneles de control
situados en un baño deben estar colocados de
manera que los interruptores y otros mecanismos de
control no puedan ser manipulados por una persona
desde la bañera o ducha.
Los dispositivos Clear Heater no deben instalarse a
una altura superior a 1,8 m.
ADVERTENCIA –No instale Clear Heater System en un
armario o techo.
Nuestros técnicos le aconsejarán e instalarán su Clear
Heater System en la posición más eficiente para
calentar su hogar de forma segura y eficaz.
Seguridad y mantenimiento
ADVERTENCIA - No deben usarse las calefacciones si
los paneles de cristal están dañados.
Los dispositivos Clear Heater son resistentes y
duraderos, pero le rogamos que evite el impacto de
objetos pesados o punzantes, como un martillo. En el
caso improbable de que el panel de cristal de su
Clear Heater se dañara, desconecte la calefacción
del enchufe, siempre que sea seguro, y contacte con
Logicor (CH) Ltd.
PRECAUCIÓN - Algunas partes de este producto
pueden recalentarse y provocar quemaduras. Preste
especial atención cuando haya niños o personas
vulnerables cerca.
Los dispositivos Clear Heater funcionan a una
temperatura normal de 70 °C (158 °F).
No se recomienda el uso de esta calefacción sin
supervisión a niños menores de 8 años, personas
enfermas, con capacidad física, mental o sensorial
reducida o sin experiencia o conocimiento del
producto. No permita que los niños jueguen con el
aparato. Los niños de menos de 3 años deben
mantenerse alejados menos que estén supervisados
continuamente.

x
Seguridad
(Español - parte 2 de 2)
Seguridad y mantenimiento
(continuación)
ADVERTENCIA - No desmonte el aparato. No contiene
partes utilizables para el usuario.
En el caso improbable de que necesite asistencia, por
favor, contacte con su distribuidor autorizado o con
Logicor en www.logicor.co.uk.
ADVERTENCIA –No utilice el aparato si el cable está
dañado.
Si el cable está dañado, debe ser reemplazado por el
fabricante, su agente de servicios o personas con
cualificación similar para evitar peligros.
ADVERTENCIA –Para evitar recalentamientos, no
cubra la calefacción.
Si desea secar ropa con Clear Heater System, por
favor, adquiera un sistema de secado de ropa de
Logicor.
El sistema de secado de ropa de Logicor ofrece una
manera rápida, segura y práctica de secar sus
prendas colocadas a una distancia segura de la
calefacción. Bajo ninguna circunstancia deben
colocarse las prendas directamente sobre un
dispositivo Clear Heater.
ADVERTENCIA: No cubrir.
Otros Advertencias y recomendaciones:
Sólo para uso interior.
No utilizar con una toma de extensión.
No cuelgue ni coloque peso en las unidades de
calentamiento.
Revise el cordón eléctrico y el enrutamiento
regularmente para detectar daños. Si está dañado
desconectarse del sistema.
unidades de calentador para ser montados en un
solo orientación vertical y horizontal.
No instale cerca o coloque materiales inflamables en
la proximidad inmediata de una unidad de
calefacción.
Limpieza
IMPORTANTE - El sensor de temperatura colocado en
la base de la calefacción está diseñado para resistir
el polvo habitual del hogar. Por favor, no utilice
abrillantadores en spray, lacas y otros productos
químicos de spray cerca del sensor, ya que puede
reducir o dañar el rendimiento. Utilice un paño seco
limpio para limpiar las calefacciones y panel de
control, pero evite abrillantadores, sprays o productos
altamente abrasivos.
IMPORTANTE - Limpieza y mantenimiento de usuarios
no serán tomadas por los niños

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 1
MENU ►Tip! Use the menu path headings at the top of each page to help you navigate through the screens
Introduction
Energy efficiency has never been more important,
especially where cost is concerned. With our smart
touch-screen control panel you will benefit from better,
more accessible information and control over your
heating costs.
The control panel is pre-programmed and ready to go
but you can follow the on-screen prompts and this user
guide to customise your settings.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………......................... (Page 53)
Section 4:
Cost & Energy Settings…......................... (Page 55)
Section 5:
Timer Settings……………......................... (Page 58)
How to use this guide
This user guide is designed to help you get the most from
your Clear Heater System and understand the different
functions available on the control panel.
Your control panel also has help messages associated
with each function; simply press the help icon at any
time.
Use the table of contents at the beginning of this guide
to find the page number of the function you need help
with and go to that page.
The nature of the control panel options means that you
may need to back-track through the screen menus in
order to fully understand how to reach your chosen
function. To do this use the MENU ►headings at the top
of each page to find the page number of each previous
screen leading up to your chosen function.
If you are using an electronic (pdf) copy of this guide
you can click any page number reference or
MENU ►headings at the top of the page to go direct to
that page.
Check out our website www.clear-heater.co.uk for
product updates.

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 2
MENU ►Tip! Use the menu path headings at the top of each page to help you navigate through the screens
Control Panel
The control panel is the ‘brain’ of the Clear Heater
System and puts you back in control of your heating
budget.
Once the control panel and Clear Heater units are
plugged into the wall socket they are ready to
communicate with each other using the electrical mains
wiring in your home. A Logicor approved installer will be
needed to carry out your installation to ensure the
heater units are positioned to achieve optimal heating.
The control panel is also equipped with Wifi capability to
receive software updates via the internet.
The control panel is pre-programmed to work out of the
box but you can change the settings at any time with
your own preferences.
For example, you can change the name and
temperature of each heater unit, link heater units to work
as one unit together, or assign heater units to work in
named zones (e.g. all bedrooms).
Use the touch screen LCD to select options or type in
your data. The menu icons on the left of the display are
your starting point for each of the following sections.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………......................... (Page 53)
Section 4:
Cost & Energy Settings…......................... (Page 55)
Section 5:
Timer Settings……………......................... (Page 58)

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 3
MENU ►Tip! Use the menu path headings at the top of each page to help you navigate through the screens
Clear Heater Units
Our unique patented infrared heaters require no
complex plumbing or wiring. A qualified installer will
advise on the best position and fit them to the wall.
Once the control panel and Clear Heater units are
plugged into the wall sockets they are ready to
communicate with each other using the electrical mains
wiring in your home.
The Clear Heating System is an all-electric phased
radiant heating system. The heaters have a very thin
carbon heating element sandwiched between two
sheets of toughened glass with a mica insert to minimise
rear facing heat loss.
We pride ourselves in making robust products that are
both elegant in design and provide solutions that work.
We are so confident in our heater system that we give
you 20 years guarantee on all heater units with a life
expectancy of over 33 years.
Important:
A Clear Heater System requires a control panel to
operate normally. Each Clear Heater unit has a
manual temperature control on the base panel. This is
only active if the heater is not connected to its control
panel and then only for a limited period of up to
eleven days before it stops working. The heater unit will
operate again once a control panel is connected.

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 4
MENU ►Help Icon
Section 1: Help Mode
Select the Help Icon on your control panel display then turn to page 5.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………......................... (Page 53)
Section 4:
Cost & Energy Settings…......................... (Page 55)
Section 5:
Timer Settings……………......................... (Page 58)

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 5
MENU ►Help Icon
Help Mode
The help icon is always there at the top left of your
screen to give you additional information about the
current control panel display.
Pressing the screen again takes you back to your
previous screen.
Options:
Press ‘Help’ Icon
Touch the help icon at any time to enter help mode.
The associated help message appears in the pop-up
box.
‘Exit’ Help
Press anywhere on the screen to take you back to
your previous display.

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 6
MENU ►Cog Icon
Section 2: Control Panel & Temperature Settings
Select the Cog Settings Icon on your control panel display then turn to page 7.
Section 1:
Help Mode……………………….............. (Page 4)
Section 2:
Control Panel & Temperature Settings (Page 6)
Section 3:
Status Screen……………......................... (Page 53)
Section 4:
Cost & Energy Settings…......................... (Page 55)
Section 5:
Timer Settings……………......................... (Page 58)

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 7
MENU ►Cog Icon
Control Panel & Temperature Settings
Here are the main control panel and temperature
settings for your installed systems.
From here you can change the main settings of your
control panel or reset completely to the original factory
settings.
Follow the page links to read more about all other
options.
Options:
Main settings (Page 8)
Adjust the main settings of the control panel, including
Wifi, time and date, tariff settings, units of
measurement, screen display options and the
fireguard function settings.
Load original settings (Page 20)
Load the original factory settings if you want to reset
the system back to its factory settings. You will be
asked to confirm your choice on the next screen .
Clear Heater System (Page 21)
Adjust your preferences for individual heater units,
create heating zones, or link heater units together to
operate as one.
Clear Heater Clothes Dryer (Page 47)
Set up and adjust the clothes dryer function.
WARNING: Please read Safety Section.
ATTENTION: Veuillez lire la section sécurité.
AVISO: Por favor, lea el apartado de seguridad.
InLine Hot Water System (Page 51)
Set up your ILHWS if installed.
Restricted mode Off (Page 52)
Safety feature when power supply is unstable.

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 8
MENU ►Cog Icon (p. 7) / Main settings
Main Settings
Set up your control panel preferences by choosing one
of the displayed options, or click the back arrow button
to go back to the previous menu.
Options:
Wifi settings (Page 9)
Amend your Wifi settings to enable the control panel
to connect to the internet for software updates or
access your control panel via your Smartphone.
Time & date (Page 10)
The time and date is needed for the control panel to
accurately regulate your heater system and provide
you with up to date performance and cost data.
Tariff settings (Page 11)
Enter your tariff rate to get accurate cost and
performance data for your system.
Country Select (Page 12)
Select your country of residence to automatically set
the time, currency and units of measurement.
Screen options (Page 13)
Edit which status messages appear on the main status
screen or change the control panel screen brightness
levels and touch-screen settings.
Frost & Fireguard (Page 19)
Frostguard will turn on a heater in any room if the
temperature falls below 3 °C.
Fireguard warns you if a heater unit detects a higher
than expected temperature in the room.

© 2016 Logicor (CH) Ltd clear-heater.co.uk Page 9
MENU ►Cog Icon (p. 7) / Main settings (p.8) / Wifi settings
Wifi Settings
Amend your Wifi settings to enable your control panel to
connect to the internet for software updates. A
Smartphone can also function as a Wifi Hotspot.
Connecting to the internet also allows you to access
your control panel via your Smartphone.
Use the keypads to type in your settings and press the
save button to store your settings.
The INFO message at the top displays the current Wifi
status.
Options:
Manual setup
Enter your network name or SSID (service set identifier)
and password to add your Wifi network to the control
panel. Use the keypads to type in your settings and
press the save button to store your settings.
Connect to an available network
Choose from the list of available networks and touch
once to connect or unselect by touching the screen
option again.