Longevity Lgap200 User manual

Longevity LGAP200

Wireless

Outdoor AP

User Manual

Table of Contents

Important Safeguards and Warnings.......................................................................... 2

Electrical Safety Information................................................................................... 2

Notice Information.....................................................................................................2

Introduction...................................................................................................................... 3

Package Contents.......................................................................................................... 3

Device Layout..................................................................................................................4

Installation - Pole mounting.......................................................................................... 5

Connection Diagram...................................................................................................... 6

Device Setup................................................................................................................... 7

Bridge Mode (Station - Secondary Site)............................................................... 8

Access Point (AP) Mode....................................................................................... 10

Repeater Mode....................................................................................................... 11

Router Mode............................................................................................................13

Application 1 - Network Extender using Bridge Mode........................................... 17

Application 2 - Network Video Recorder + Camera............................................... 18

Installation Considerations..........................................................................................19

FAQs...............................................................................................................................19

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 2 ----

Important Safeguards and Warnings

Please read the following safeguards and warnings carefully before using the product in

order to avoid damages losses and body injuries.

Electrical Safety Information

This product uses 48V POE as power source. Connection to a different power source

than those specified may result in improper operation, damage to the equipment or pose

a fire hazard if the limitations are not followed.

There are no operator serviceable parts inside this equipment. Service should be

provided only by a qualified service technician.

Do not use this product in location that can be submerged by water.

Do not install this product during an electrical storm. There may be a risk of electric shock

from lightning.

Notice Information

All the designs, software and instructions here are subject to change without prior written

notice.

We would not be responsible for any damages and losses caused by improper

operations or installation. Do not allow non-authorized or unqualified personnel with any

kind of intervention to the product.

All trademarks and registered trademarks are the properties of their respective owners.

Please visit our website www.rhinoco.com.au for more information.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 3 ----

Introduction

Longevity LGAP200 is designed for long distance transmission of IP packets which is

commonly used in PC network and network cameras. It has four working modes: Access

Point, Bridge, Repeater and Router.

Package Contents

Confirm that the following parts are included:

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 4 ----

Device Layout

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 5 ----

Installation - Pole mounting

1. Install the stainless straps to the back of the device as shown.

2. Align the device on the pole and then fasten the straps.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 6 ----

Connection Diagram

1. Connect the power cord to the power connector on the back of the POE injector. Plug the

other end of the power cord into an AC (mains) power outlet.

2. Connect the LAN port of the Longevity LGAP200 to your PC/Laptop or IP camera’s

Ethernet port with an Ethernet cable.

3. Connect the WAN port of the Longevity LGAP200 to the POE port of the POE injector

with an Ethernet cable.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 7 ----

Device Setup

1. Connect the device as shown above.

2. Change the IP address of your PC/Laptop to 192.168.10.199. (Other number except

192.168.10.1 may also work)

3. The default IP address of the device is 192.168.10.1. Open your web browser and type

192.168.10.1 into the address bar of your browser and press <ENTER>.

Note: If the browser is not working properly, clear the cache and cookies data of the browser.

Restart the browser and try again. (Internet Explorer or Microsoft Edge is recommended)

4. Input the password and click Login. The default password is admin.

5. Click the Wizard icon on the left panel to select operating mode.

Longevity LGAP200 has 4 working modes: Router, Bridge,Access Point (AP) and

Repeater.

Mode

Function

Bridge

Connect two network segments wirelessly

(Access Point)

When connects to a wired router or switch with internet access, it creates a

wireless local area network (WLAN) for other devices such as mobile phones,

laptops etc.

Repeater

It repeats signal from a wireless router or wireless access point and rebroadcasts

the signal to other wireless devices.

Router

It provides access to the Internet or a private wireless computer network (WLAN).

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 8 ----

Bridge Mode (Station - Secondary Site)

i. Change the IP address and subnet mask if required then click Next to continue.

ii. Click Scan to scan all available WiFi signal. (Only 5G WiFi signal will be

displayed.)

iii. Click to select the WiFi to be bridged.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 9 ----

iv. Input the WiFi password of the select WiFi and click Next to continue.

v. Input the SSID in SSID and customize the password in Password for 2.4G and

5.8G WiFi settings.

vi. Click Finish to complete setup.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 10 ----

Access Point (AP) Mode

i. Change the IP address and subnet mask if required then click Next to continue.

ii. Enter a unique wireless network name (SSID) in the Local SSID field and then a

8-32 characters password. Leave other settings as default values.

iii. Click Finish to complete setup.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 11 ----

Repeater Mode

i. Change the IP address and subnet mask if required then click Next to continue.

ii. Click Scan to scan the WiFi to repeat.

iii. Click to select the WiFi to repeat.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 12 ----

iv. Input the WiFi password of the select WiFi and click Next to continue.

v. Input the SSID in SSID and customize the password in Password for 2.4G and

5.8G WiFi settings then click Next to continue.

vii. Click Finish to complete setup.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 13 ----

Router Mode

Select the internet connection type: PPPoE, Static - Static IP or DHCP.

a) PPPoE

i. Enter Username and Password for the PPPoE account then click Next to

continue.

ii. Change the IP address and subnet mask if required then click Next to continue.

iii. Input the SSID in SSID and customize the password in Password for 2.4G and

5.8G WiFi settings then click Next to continue.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 14 ----

viii. Click Finish to complete setup.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 15 ----

b) Static IP

i. Input the static IP address, Subnet mask, Gateway and DNS for the router then

Click Next to continue.

ii. Change the IP address and subnet mask if required then click Next to continue.

iii. Input the SSID in SSID and customize the password in Password for 2.4G and

5.8G WiFi settings then click Next to continue.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 16 ----

iv. Click Finish to complete setup.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 17 ----

Application 1 - Network Extender using Bridge Mode

In this example, one device works in AP(Access Point) mode and another one works in Bridge mode(Client).

Note: Must use different IP address for the AP(Access Point) and Bridge client.

Longevity LGAP200 User Manual V1.0 Issued 2020-5-13

---- 18 ----

Application 2 - Network Video Recorder + Camera

Table of contents

Other Longevity Wireless Access Point manuals

Longevity

Longevity LGAP100-4G User manual

Longevity

Longevity LGAP300 User manual

Longevity

Longevity COM007 User manual

Popular Wireless Access Point manuals by other brands

Ubiquiti

Ubiquiti UniFI UAP-AC quick start guide

Nortel

Nortel BayStack 660 Use guide

TRENDnet

TRENDnet TEW-410APBplus Specifications

Draytek

Draytek VigorAP 920C quick start guide

SENAO

SENAO 2511BG2 PLUS Hardware installation guide

Avaya

Avaya AP-4 user guide

EnGenius

EnGenius EMD1AP user manual

D-Link

D-Link xtreme n duo dap-1522 user manual

Genexis

Genexis FiberTwist Series installation guide

3Com

3Com OfficeConnect 3CRWE454A72 Technical brief

IP-COM

IP-COM W45AP Quick install guide

TRENDnet

TRENDnet TPL-110AP - 125Mbps 802.11g Wireless Powerline Access... Specifications

Sercomm

Sercomm Englewood HGO Quick installation guide

Cisco

Cisco WAP371 quick start guide

Siemens

Siemens SCALANCE W786-x operating instructions

Huawei

Huawei AP3010DN-AGN Hardware installation and maintenance manual

DKT Comega

DKT Comega HomeMesh IPLoA-MESH-AC-W quick start guide

Cisco

Cisco MR18 quick guide

Longevity LGAP200 User manual

Popular Wireless Access Point manuals by other brands