Longse LTP24 User manual

User Manual
Please read this manual carefully before installation

Content
Important Safety Measures 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。3
Notes 。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。3
Operation Instruction
ⅠCamera Controlling。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。4
Ⅱ Pre-set setup。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。4
Ⅲ Calling Preset Point。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。4
Ⅳ Deletion of preset。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。4
ⅤSwitches Inside Instruction。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。4
ⅥConnection Diagram。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。5
ⅦSetting of Dome Device communication。。。。。。。。。。。。。。。。。。。。。。7
ⅨCamera Controlling。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。8
Specifications。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。。9

Important Safety Measures
1. Please read this manual carefully before installation.
2. All of the warned items should be strictly abided by.
3. The operation and usage instruction should be abided by.
4. Please use the accessories which recommended by the seller. Otherwise, we are not responsible
for the damage caused by inappropriate accessories.
5. I you have any questions about the using voltage of this product, please contact the seller.
6. Please do not disassemble this product yourself, if any problem happens, please contacts the
seller.
7. Clash and oscillation should be avoided. If the product will be damaged if not be stored
improperly,
8. Please do not use Corrosive detergent to clean this product; When the product body is dirty, please
use dry and soft fabric to wipe it. If necessary, neutral detergent can be used. Please be careful
about the housing
9. In case of the following situations, please contact the seller;
a. Power supply or control line is damaged.
b. The housing damaged
c. Abnormal equipment performance
d. Do not work after operate according to user manual
10．When replacement the parts, please use the parts provided by seller or with similar functions.
Unauthorized substitutes will be dangerous and damage equipment.
Notes
1．Do not use the product in the raining or damp places.
2．Do not aim the camera to the sun.
3．Do not make the camera aim at the bright objects for a long time, whether the camera is in use or
non-use. Otherwise, the image may have blurred or Halo.
4．Do not make the camera facing the strong light or exposing to the light source.
5．Reverse installation is forbidden.
This product is designed for ceiling and wall. If installed reversely, such as used on the floor, the
camera could not work normally.
6. Do not use the camera under the situation which exceeds the operation temperature or humidity or
power specifications.

Operation Instruction:
ⅠCamera Controlling:
Press the number button at the bottom part of remote controller to control the camera, each
number stands for one address, the system defaulted address is 1, “0” stands for “10”.
Ⅱ Pre-set setup:
1: Press “up, down, left, right” Direction Key on the remote controller steer the camera to the
required position. When satisfied with the camera’s position, Press “set” button for 3 seconds,
till LED shows “SET-”
2. Then press the button of number you want to preset at the top part of remote controller
3. When the LEN flashes, it means the preset finished.
Ⅲ Calling Preset Point:
Press the preset No. you have set; the camera can steer into the preset position.
Auto Scan:
1. preset the position “A” and “B”.
2. Press the Key “S1","S2","S3"or"S4” to scan automatically from the Position “A” to “B”.
The speed controlled by “S1” is the slowly, the speed controlled by”S4” is the fastest.
3. The key”F2” also can control the scan direction, from Left to Right.
Ⅳ Deletion of preset:
Press “CLEAR” for 3 seconds, and select the pre-set point for deletion.
ⅤSwitches Inside Instruction:
No.1-7: Address code of cameras, the code No. can be set as: 00-127 (The controller just can
control 10pcs cameras at present.)
No.8: Baud rate: OFF: 2400; ON: 9600, the defaulted is 2400 (The controller only support
2400)
No.9: Protocol: ON: protocol-P; OFF: protocol-D, the defaulted is protocol-D (The controller
only support protocol-D)
No.10: Resistance between RS485 + and RS485 -: OFF: no resistance; ON: 120ohms.
Among all cameras, which controlled by the same one remote controller, the one (camera)
with the longest cable (16 meters at the most) needs to be switched to “ON”. (Note: when all
cameras controlled by the same one remote controller, only one camera can be switched to”
ON”)

ⅥConnection Diagram
The IR remote controller can control only 10 pcs domes at present.
Anode
Cathode
RS-485
Control

Dome device
controller
Image
displaye
Power
of
dome
DC
Video
RS-485
Image
displaye
Power
of
dome
DC
Video
Image
displa
Power
of
dome
Dome #1
Dome #2
Dome
RS-485
RS-485
Bus
DC
Video
#N
RS-485
(Wiring of multi-dome)

ⅦSetting of Dome Device communication ation Protocol and transmission speed
1. Dismantlement of Dome Device. (Shown as illustrations.)
Before installation and use, the setting of communic
(baud rate) should comply with the control system.
.
．Setting Protocol and baud rate of dome device.
2
tocol Rate Setting:
1 2 3 4 5 6 7 8 9 0
Baud Rate Setting:
OFF: 2400 bps
ON: 9600 bps
Pro
OFF: Protocol-D
ON: Protocol-P
Baud Rate Setting
Resistance Setting
Protocol Setting
ON
1 2 3 4 5 6 7 8 9 0
Baud Rate: 9600 bps
Setting address of dome

3. Setting of Dome’s Address
ⅨCamera Controlling ddress in parallel connection, you can control each camera by
are 3 cameras in parallel connection, the first camera address is set into
On/Of
Setting method: The sum of switch numbers when it is at ON
f switch
position is the address of dome device.
Setting address for dome device
After setting each camera’s a
their own address.
For instance, if there
22, the second address is set into 36, and the third camera address is set into 42. If you want
to control the first cameras, you can press the No.22 on the remote controller, and then control
the camera. When you want to control the second camera, you can press the No.42, then to
control the second one.
(this figure shows the address of
dome device No 1
)
.
On/off switch and matching numbers
1
2
4
8 16
32
64
128
2 4 16
Matching the number
Calculation example of dome device address:
(2+4+16=22) The address is 22.

Specifications
CCD SONY/SHARP
Image Sensor 1/3inch /1/4inch
Video output 1.0Vp-p
Horizontal Resolution 420/480TVL
IR LED 5mm 24pcs
Usable Illumination 0LUX
Lens Board Lens 6mm/F2.0
Pan range 360°
Pan speed 1~80 degree/second
Tilt range 90°
Tilt speed 1~80 degree/second
Communication RS-485
Preset 16(optional Max 64)
Protocal Pelco-P/D
Vector scan track 1
Power supply AC220V/AC110V/DC12V
optional; 9W
Operation Temperature -30℃~65℃