Lopi Spirit B-Vent Gas Stove User manual

TM
Owner's Manual
- November, 1999 -
WARNING: If the information in this manual is not followed exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any
other appliance.
- WHAT TO DO IF YOU SMELL GAS
¥ Do not try to light any appliance.
¥ Do not touch any electrical switch; do not use any phone in your building.
¥ Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
¥ If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Spirit B-Vent Gas Stove
10850 117th Place N.E. Kirkland, WA 98033
$10.00 93508054 Listed

PAGE 2SAFETY PRECAUTIONS
¥ IF YOU SMELL GAS:
* Do not light any appliance
* Extinguish any open flame
* Do not touch any electrical switch or plug or unplug anything
* Open windows and vacate building
* Call gas supplier from neighbor's house, if not reached, call fire department
¥ This unit must be installed by a qualified installer to prevent the possibility of
an explosion. Your dealer will know the requirements in your area and can
inform you of those people considered qualified. The room heater should be
inspected before use and at least annually by a qualified service person. More
frequent cleaning may be required due to excessive lint from carpeting,
bedding material, etc.
¥ The instructions in this manual must be strictly adhered to. Do not use
makeshift methods or compromise in the installation. Improper installation
will void the warranty and safety listing.
THIS CONTROL
HAS BEEN
CONVERTED TO
LP
THIS CONTROL
HAS BEEN
CONVERTED FOR
NATURAL GAS
¥ This heater is either approved for natural gas
(NG) or for propane (LP). Burning the
incorrect fuel will void the warranty and safety
listing and may cause an extreme safety
hazard. Direct questions about the type of fuel
used to your dealer. Check the label and flame
adjust knob on the gas control valve.
Ok
¥ Contact your local
building officials to
obtain a permit and
information on any
installation restrictions or
inspection requirements in
your area. Notify your
insurance company of this
heater as well.
¥ If the flame becomes
sooty, dark orange in
color, or extremely tall,
do not operate the heater.
Call your dealer and
arrange for proper
servicing.
¥ It is imperative that
control compartments,
screens, or circulating air
passageways of the heater
be kept clean and free of
obstructions. These areas
provide the air necessary
for safe operation. ?
¥ Do not operate the heater
if it is not operating
properly in any fashion or
if you are uncertain. Call
your dealer for a full
explanation of your heater
and what to expect.
Gas
¥ Do not store or use
gasoline or other
flammable liquids in the
vicinity of this heater.
¥ Keep all furniture or other
combustible items at least
36" away from the front
of the heater.
AAAA
AAAA
AAAA
AAAA
A
¥ Do not operate if any
portion of the heater was
submerged in water or if
any corrosion occurs.

SAFETY PRECAUTIONS (CONTINUED)PAGE 3
¥ Do not place clothing or
other flammable items on
or near the heater.
Because this heater can be
controlled by a thermostat
there is a possibility of the
heater turning on and
igniting any items placed
on or near it.
AA
AA
AA
AA
A
¥ Light the heater using the
built-in piezo igniter. Do
not use matches or any
other external device to
light your heater.
¥ Never remove, replace,
modify or substitute any
part of the heater unless
¥ The viewing glass should
be opened for service only
(see the maintenance
section of this manual).
¥ Any safety screen or
guard removed for
servicing must be
replaced prior to
operating the heater.
instructions are given in
this manual. All other
work must be done by a
trained technician. Don't
modify or replace orifices.
¥ Allow the heater to cool
before carrying out any
maintenance or cleaning.
¥ Operate the heater
according to the
instructions included in
this manual.
¥ If the main burners do not
start correctly turn the gas
off at the gas control
valve and call your dealer
for service.
¥ The pilot flame must
contact the thermopile
and thermocouple (see the
illustration to the left). If
it does not, turn the gas
control valve to "OFF"
and call your dealer.
A
A
¥ This unit is not for use
with solid fuel
¥ Do not place anything
inside the firebox (except
the included fiber logs).
¥ If the fiber logs become
damaged, replace with
Travis Industries log set.
This
Manual
¥ Do not throw this manual
away. This manual has
important operating and
maintenance instructions
that you will need at a
later time. Always follow
the instructions in this
manual.
¥ Do not touch the hot
surfaces of the heater.
Educate all children of the
danger of a high-
temperature heater.
Young children should be
supervised when they are
in the same room as the
heater.
¥ Plug the heater into a
115V grounded electrical
outlet. Do not remove the
grounding plug.
¥ Don't route the electrical
cord in front of, over, or
under the heater
¥ Instruct everyone in the
house how to shut gas off
to the appliance and at the
gas main shutoff valve.
The gas main shutoff
valve is usually next to
the gas meter or propane
tank and requires a
wrench to shut off.
¥Travis Industries, Inc.
grants no warranty,
implied or stated, for the
installation or
maintenance of your
heater, and assumes no
responsibility of any
consequential
damage(s).

PAGE 4TABLE OF CONTENTS
General Information
Introduction & Important Information ............. 1
Safety Precautions......................................... 2
Features & Specifications
Installation Options ........................................ 5
Features......................................................... 5
Heating Specifications ................................... 5
Dimensions.................................................... 5
Fuel................................................................ 5
Emissions....................................................... 5
Electrical Specifications ................................. 5
Stove Installation
Installation Preparation.................................. 6
Items Packed with the Heater........................ 6
Additional Items Required for Stove Install.... 6
Order of Installation ....................................... 6
Stove Clearances .......................................... 6
Heater Placement Requirements................... 7
Floor Protection ............................................. 7
Gas Line Installation ...................................... 7
Gas Inlet Pressure ......................................... 7
Vent Requirements........................................ 8
Vent Termination Requirements.................... 8
Electrical Connection ..................................... 8
Finalizing the Installation
1 Removing the Glass ................................... 9
2 Installing the Logs and Embers .................. 10
3 Installing the Door....................................... 11
4 Purging the Gas Line.................................. 12
5 Checking the Pilot Flame............................ 12
6 Checking the Draft...................................... 12
7 Adjusting the Air Shutter ............................. 13
8 Checking the Flame Height ........................ 13
9 Explaining Heater Operation to the Owner . 13
Operating Your Heater
Before You Begin.......................................... 14
Location of Controls....................................... 14
Starting The Pilot ........................................... 15
Starting the Heater for the First Time ............16
Turning the Heater On and Off ..................... 16
Adjusting the Flame Height............................16
Adjusting the Blower Speed.......................... 17
Normal Operating Sounds ............................. 17
Maintaining Your Heater
Yearly Service Procedure .............................. 18
Troubleshooting
Troubleshooting Table .................................. 19
How this Heater Works ................................. 20
What Turns the Main Burners
On and Off .............................................. 20
What Prevents Gas Buildup................... 20
Why Nothing Should Be Placed
Against the Heater ................................. 21
Wiring Diagram...................................... 21
Warranty
Warranty ........................................................22
Listing Information
Safety Label................................................... 23
Optional Equipment
Legs Installation............................................. 24
Pedestal Installation...................................... 24
Thermostat.................................................... 25
Remote Control (with Thermostat)................. 26
Outside Air Kit ............................................... 26
Propane Conversion Kit................................. 26
Index
Index ..............................................................30
Symbols Used in this Manual
The illustration below details what the symbols used along the left margin indicate.
Requirement
¥¥
¥¥ 11 11 !! !! ?? ?? ++ ++
Hint
NoteWarningStep

FEATURES AND SPECIFICATIONS PAGE 5
Installation Options:
¥ Freestanding
Features:
¥ Works During Power Outages
(millivolt system)
¥ High Efficiency; Up to 80% for Natural Gas,
82% for LP (Steady State)
¥ Optional Thermostat or Remote Control
¥ Realistic "Wood Fire" Look
¥ Convenient Operating Controls
¥ Variable-Rate Heat Output
¥ Quiet Blower for Effective Heat Distribution
¥ Low Maintenance
Heating Specifications:
Approximate Heating Capacity (in square feet)* 600 - 1600
AFUE (Annual Fuel Utilization Efficiency) 68 %
Natural Gas LP (Propane)
High Burn Input Rate (In BTU's) 40,000 38,000
Low Burn Input Rate (In BTU's) 23,000 20,000
Efficiency** 80% 82%
* Heating capacity will vary with the home's floor plan and insulation, natural gas or Propane BTU rating, and outside temperature.
** Efficiency rating is a product of thermal efficiency rating determined under continuous operation independent of installed system.
To measure the net BTU's, multiply the BTU input by the efficiency percentage (80% for natural gas, 82% for LP).
Dimensions
18-3/4"
24"
4-7/8"
Pedestal: 34-7/8"
Brass, Cast Legs: 30-7/8"
Black Legs: 29-1/2"
Vent Dia. 4"
Weight: 205 Lbs.
The base of the starter
section is 4-3/4" below
the upper top.
Measure
clearances to
the upper top
Fuel: The heater is designed either for natural gas or for propane (but not
for both). Check the sticker on the top of the gas control valve.
Emissions: This unit has passed the ANSI emission standards for vented room
heaters as tested by OMNI Environmental Services, Inc.
Electrical Specifications: 115 Volts, 1.3 Amps, 60 Hz (150 watts on high)

PAGE 6STOVE INSTALLATION -For qualified installers only!
Installation Preparation
! This appliance must be installed in accordance with all local codes, if any; if not, follow ANSI
Z223.1 and the requirements listed in this manual. Failure to follow all of the requirements
may result in property damage, bodily injury, or even death.
! Notify your insurance company before hooking up this heater.
! The requirements listed below are divided into sections. All requirements must be met
simultaneously. The order of installation is not rigid Ð the qualified installer should follow the
procedure best suited for the installation.
Items Packed with the Heater
¥Lopi Spirit Gas Heater
¥Log Set (2 Logs, 2 Twigs, Coals)
¥Owner's Manual
¥Door Kit (Door handle, mounting angle, T-nut)
¥Propane Conversion Kit
¥ Gas Inlet (3/8" Pipe)
Additional Items Required for Stove Installation
¥Brass or Black Door Frame
¥Brass, Black, or Cast Legs or Pedestal
Order of Installation
1If the heater is to use propane, follow the instructions on pages 28 - 34.
2Attach the legs or pedestal (see page 24) and optional equipment (if applicable)
3Position the heater (measure clearances from the upper top), use floor protection if needed
4Connect the gas line
5Connect the gas vent
6Follow the instructions under "Finalizing the Installation" on pages 9 through 13.
Stove Clearances
10" Min.
4" Min.
When installed with this
clearance, the vent is
6-1/2" from the back
wall, 19-3/4" from the
side wall.
Straight Installations
45¡
Corner Installations
When installed with this clearance, the
vent is 13" from the wall.
4" Min.
+Clearances may be reduced by methods specified in NFPA 211, listed wall shields, pipe shields, or
other means approved by local building or fire officials.

STOVE INSTALLATION (CONT.) - For qualified installers only! PAGE 7
Heater Placement Requirements
¥Heater must be installed on a level surface capable of supporting the heater and vent
¥Due to the high temperature of the heater, it should be located out of traffic and away from furniture and draperies. Heater
must be placed so no combustibles are within, or can swing within 36" of the front of the heater (e.g. drapes, doors)
?When placed in a location where the floor to ceiling height is under 7 feet , the installation is considered an alcove and
must meet the following requirements:
¥The alcove floor to ceiling height must be at least 58" tall
¥The alcove must not be more than 48" deep (before the ceiling returns to 7 feet)
¥The alcove must be at least 43-3/4" wide
¥The stove must not be placed so the vents below or above the door, along the sides of stove, or along the back of the
heater can become blocked.
Floor Protection
¥When the stove is installed directly on carpeting, vinyl or other combustible material other than wood flooring or a high
pressure laminate wood floor, the stove must be installed on a metal or wood protection panel extending the full width
and depth of the heater (Minimum 24Ó wide by 18-3/4Ó deep).
Gas Line Installation
!The gas line must be installed in accordance with all local codes, if any; if not, follow ANSI Z223.1 and the requirements
listed below.
!The heater and gas control valve must be disconnected from the gas supply piping during any pressure testing of that
system at test pressures in excess of 1/2 psig. For pressures under 1/2 psig, isolate the gas supply piping by closing the
manual shutoff valve.
¥This heater is designed either for natural gas or for propane (but not for both). Check the sticker on the top of the gas
control valve to make sure the correct fuel is used.
¥Leak test all gas line joints and the gas control valve prior to and after starting the heater.
¥The gas inlet accepts a 3/8" F.P.T. Fitting
¥The location of the gas inlet is shown below
¥A manual shutoff valve is required for installation (it must be located within 3' of the heater)
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
A
A
A
A
A
A
A
A
A
AA
AA
A
A
AA
A
AA
A
A
A
Rear
Panel
Gas Inlet
(3/8" diameter pipe)
AA
AA
NOTE:
Apply thread
sealant prior to
installing.
A
Use a pipe wrench
to tighten in place.
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
A
A
A
A
A
A
A
A
A
A
A
AA
AA
A
A
AA
A
13-1/2" Pedestal
9-1/2" Brass/Cast Legs
8" Steel Legs
1-1/2"
7-1/2"
Center of
Stove
Gas Inlet Pressure
¥With the heater off, the inlet pressure must meet the requirements listed in the table below
?If the pressure is not sufficient, make sure the piping used is large enough and the total gas load for the residence does
not exceed the amount supplied.
?The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should supply gas
at the suggested input pressure listed below. Contact the local gas supplier if the regulator is at an improper pressure.
Standard Input Pressure
Natural Gas 7" W.C.
Propane 11" W.C.

PAGE 8STOVE INSTALLATION (CONT.) - For qualified installers only!
Vent Requirements
!Always maintain the required 1" clearance (air space) to combustible materials to prevent a fire
hazard. Do not fill air spaces with insulation.
!The gas appliance and vent system must be vented directly to the outside of the building, and never
be attached to a chimney serving a separate solid fuel or gas-burning appliance.
¥Minimum 5' vertical rise
from top of stove
¥When the vent passes
through a wall, a wall
thimble is required.
When the vent passes
through a ceiling, a
support box or firestop is
required. When the vent
passes through the roof,
a roof flashing and storm
collar are required.
Follow the instructions
and requirements
provided with the vent
when installing.
¥The horizontal run may
not exceed 50% of the
vertical rise
AAAAAA
AAAAAA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Type B Vent
Vent must
terminate a
minimum 1'
above the roof.
Listed Gas
Chimney Liner
Maintain 1"
minimum
clearance
Provide a 1/4" rise
for every 12" run.
AAAAAA
AAAAAA
Min. 5' Rise High
temperature
factory built
chimney and
connector
Chimney with LinerStandard Installation Exterior Vent
Min. 5' Rise
The total
horizontal
run must
not exceed
50% of the
vertical rise
Do not block gas
vent termination
¥Use 4" dia. B vent for entire system from one manufacturer (don't mix brands)
- or -
Use high temperature factory built or masonry chimney with listed gas chimney liner running the
entire length
¥Vent termination must be above the roof and not below any eaves or overhangs
Drafting
Performance
This appliance relies upon natural draft to operate. External forces, such as wind,
barometric pressure, topography, or factors of the home (negative pressure from exhaust
fans, chimneys, air infiltration, etc.), may adversely affect draft. Travis Industries can
not be responsible for external forces leading to less than optimal performance.
Vent Termination Requirements
¥Vent termination must have an approved cap (to prevent water from entering)
¥Vent termination must not be located where it will become plugged by snow or other material
¥Vent termination must be
1' above the roof and
meet the requirements
outlined in ANSI
Z223.1, section 7.6.2.
12Ó Min.
Note: ANSI 223.1, section 7.6.2 outlines additional
requirements for gas vent terminations. If your
installation involves a roof with a slope greater
than 6/12 or if a wall or other vertical obstruction is
within 8' of the vent termination, the vent
termination will need to be taller. Refer to ANSI
223.1 for full details.
!When installed, the vent must provide suitable draft for the appliance. Other factors, such as exhaust
fans, may create negative pressure inside the home and cause down drafts. Additional vent height
may be required in these circumstances.
Electrical Connection
¥Plug the power cord into a grounded 110 Volt outlet (do not remove the grounding plug).

FINALIZING THE INSTALLATION -For qualified installers only! PAGE 9
1Remove the glass.
Cross Section of
Glass Attachment
AA
AA
AA
AA
AA
AA
AA
Glass
Glass Gasket
(5/8" self-adhesive
channel gasket)
Glass Clip
Glass Clip
Attachment Studs
Face of Heater
Glass Clip Nuts
a
5/16" Nutdriver
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
AAAAAA
b
Loosen the nuts on the bottom and
left side glass clip. Then slide the
glass to the right, pivot the glass
forward, and remove it from the
heater.
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
Follow the directions above in reverse order. Make sure the
gasket forms an air-tight seal around the perimeter of the glass.
To remove the glass:
To replace the glass:
Loosen the nuts on the top and
right side glass clips. Then
slide the glass clips off.
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA
AAAAAAA

PAGE 10 FINALIZING THE INSTALLATION (CONT.) - For qualified installers only!
2Install the log set and embers (see the illustration below).
Rear Log (largest)
Front Log
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Burner Pan
The rear log has a
flat portion that
rests on this ledge.
The front log rests on
these platforms.
These clips keep the rear log
from tilting backwards.
Log Installation
Twig
Installation
A
A
A
A
A
A
A
A
A
A
A
A
A
A
Slide the front log all the way
back against the air deflector.
The rear log
protrudes over the
burner pan on both
sides.
The front edge of
the front log rests
on this ledge.
The rear log contacts
the air deflectors.
Align the holes
in the left twig
over the pegs
on the front and
back logs.
Ember
Installation
Place the embers on this ledge at the
front of the firebox . Do not place the
embers over the burner holes.
A
A
A
A
A
A
AA
A
AA
A
A
AA
AA
A
A
Align the holes
in the right twig
over the pegs
on the left twig
and back log.
3Replace the glass (see the illustration on the previous page).