Lopi Evergreen User manual

Evergreen
Wood Stove
Owner's Manual
Freestanding Stove
Hearth-Stove Approved
Save these instructions
for future reference
SAFETY NOTICE:
If this appliance is not properly installed, a house fire
may result. For your safety, follow the installation
directions. Contact local building or fire officials about
restrictions and installation inspection requirements
in your area.
Dragon Wholesaling Pty. Ltd.
Unit 4, 16 Lexington Drive
Bella Vista NSW
Australia 2153
Copyright 2016,
Travis Industries, Inc.
$10.00
100-01438
4160303
Tested by:
HRL Technology
Tramway Road, Morwell 3840
Victoria
Tested to: AS/NZS 4012/4013: 2014
Report Number: HCMG-016-006

2 Introduction
© Travis Industries 100-01438 4160303
Introduction
We welcome you as a new owner of a Lopi Evergreen wood-burning stove. In purchasing an Evergreen
you have joined the growing ranks of concerned individuals whose selection of an energy system reflects
both a concern for the environment and aesthetics. The Evergreen is one of the finest appliances the
world over. This manual will explain the installation, operation, and maintenance of this appliance.
Please familiarize yourself with the Owner's Manual before operating your appliance and save the manual
for future reference. Included are helpful hints and suggestions which will make the installation and
operation of your new appliance an easier and more enjoyable experience. We offer our continual
support and guidance to help you achieve the maximum benefit and enjoyment from your appliance.
Important Information
No other Evergreen wood stove has the same serial
number as yours. The serial number is stamped onto
the label on the back of the appliance.
This serial number will be needed in case you require
service of any type.
Model: Lopi Evergreen Wood Stove
Serial Number:
Purchase Date:
Purchased From:

Table of Contents 3
© Travis Industries 100-01438 4160303
Introduction ......................................................2
Important Information......................................2
Installation Options..........................................6
Features ............................................................6
Heating Specifications.....................................6
Dimensions.......................................................6
Emissions .........................................................6
Planning the Installation..................................7
Preparation for Installation....................................7
Packing List......................................................7
Floor Protection Requirements ......................8
Stove Placement Requirements .....................8
Clearances........................................................8
Chimney Connector Requirements................9
Chimney Requirements.................................10
Chimney Termination Requirements ...........11
Outside Air Requirements.............................11
Standard Ceiling with a Factory-Built Chimney...12
Cathedral Ceiling with a Factory-Built Chimney..12
Exterior Factory-Built Chimney ...........................13
Wall Penetrations Under 1.8796 meters (74”) ........13
Hearth Stove Installation.....................................14
Interior or Exterior Masonry Chimney .................14
Safety Notice ..................................................15
Before Your First Fire....................................15
Curing the Paint..................................................15
Carbon Monoxide (CO) Emissions......................15
Over-Firing the Stove..........................................15
Opening the Door...........................................16
Bypass Operation ..........................................16
Starting a Fire.................................................17
Adjusting the Burn Rate................................18
Approximate Air Control Settings........................18
Understanding Your Heater’s Combustion
System.............................................................19
Burning Your Heater......................................19
Ash Removal..................................................20
Ash Pan ..............................................................20
Re-Loading the Stove....................................22
Overnight Burn...............................................22
Normal Operating Sounds ............................22
Hints for Burning ...........................................23
Selecting Wood..............................................23
Why Dry Wood is Key.........................................23
Wood Cutting and Storage..................................23
Do Not Burn List..................................................24
Troubleshooting.............................................25
Daily Maintenance (while stove is in use)...26
Clean the Glass (if necessary)............................26
Monthly Maintenance (while appliance is in
use)..................................................................27
Door and Glass Inspection..................................27
Door Adjustment.................................................27
Creosote - Formation and Need for Removal .....28
Yearly Maintenance ....................................... 28
Touch-Up Paint...................................................28
Cleaning the Air Duct and Blower.......................28
Firebrick and Baffle Inspection............................28
Door Parts.......................................................29
Replacing the Glass............................................29
Replacing the Door Gasket.................................29
Replacing the Door Handle.................................29
Removing the Door.............................................29
Firebox Parts..................................................30
Baffle Removal & Replacement....................30
Air Tube Removal & Replacement...............31
Firebrick Removal & Replacement.................32
Listing Label...................................................35
Optional Rear Blower (Part # 99000143)......36
GreenStart™Woodstove Igniter (Part #
94400953)........................................................36
GreenStart Igniter Installation Addendum..37

4 Safety Precautions
© Travis Industries 100-01438 4160303
The viewing door must be
closed and latched during
operation.
Smoke from this appliance may
activate a smoke detector when
the door is open.
Never block free airflow through
the air vents on this appliance.
Gasoline or other flammable
liquids must never be used to
start the fire or "Freshen Up" the
fire. Do not store or use
gasoline or other flammable
liquids in the vicinity of this
appliance.
This appliance is designed and
approved for the burning of cord
wood only. Do not attempt to
burn any other type of fuel other
than cord wood in this
appliance, it will void all
warranties and safety listings.
Ashes must be disposed in a
metal container with a tight lid
and placed on a non-
combustible surface well away
from the home or structure.
Do not touch the appliance while
it is hot and educate all children
of the danger of a high-
temperature appliance. Young
children should be supervised
when they are in the same room
as the appliance.
Keep furniture, drapes, curtains,
wood, paper, and other
combustibles a minimum of
914mm (36") away from the
front of the appliance.
This appliance must be properly
installed to prevent the
possibility of a house fire. The
instructions must be strictly
adhered to. Do not use
makeshift methods or
compromise in the installation.
Contact your local building
officials to obtain a permit and
information on any installation
restrictions or inspection
requirements in your area.
Notify your insurance company
of this appliance as well.
Inspect the chimney connector
and chimney at least twice
monthly and clean if necessary.
Creosote may build up and
cause a house fire.
Do not connect this appliance to
any chimney serving another
appliance.
This appliance must be
connected to a listed high
temperature (UL 103 HT)
residential type chimney or an
approved masonry chimney with
a standard clay tile, or stainless
steel liner.
Gas
ASHES
36"
Ok
Type
HT Clay
Liner

Safety Precautions 5
© Travis Industries 100-01438 4160303
Do not place clothing or other
flammable items on or near this
appliance.
Never try to repair or replace
any part of this appliance unless
instructions are given in this
manual. All other work must be
done by a trained technician.
Do not make any changes or
modifications to an existing
masonry fireplace or chimney to
install this appliance.
This wood heater has a
manufacturer-set minimum low
burn rate that must not be
altered. It is against federal
regulations to alter this setting or
otherwise operate this wood
heater in a manner inconsistent
with operating instructions in this
manual.
Allow the appliance to cool
before carrying out any
maintenance or cleaning.
Over-firing the appliance may
cause a house fire. If a unit or
chimney connector glows, you
are over-firing.
Maintain the door and glass seal
and keep them in good
condition.
Do not operate this heater with
broken or missing glass.
Avoid placing wood against the
glass when loading. Do not
slam the door or strike the glass.
Do not use a grate or other
device to elevate the fire off of
the firebox floor. Burn the fire
directly on the firebox floor.
Do not throw this manual away.
This manual has important
operating and maintenance
instructions that you will need at
a later time. Always follow the
instructions in this manual.
Travis Industries, Inc. grants
no warranty, implied or
stated, for the installation or
maintenance of your
appliance,and assumes no
responsibility of any
consequential damage(s).



This
Manual

6 Features & Specifications
© Travis Industries 100-01438 4160303
Installation Options
Freestanding
Optional GreenStart Igniter
High-Tech Blower
Features
0.0577 cubic meter (2.04 Cubic Foot) Firebox
Volume
Single Operating Control
Accepts Logs Up to 521mm (20.5") Long
Steel Plate Construction (6.3mm & 4.7mm)
Heavy Duty Refractory Firebrick
Heating Specifications
Approximate Maximum Heating Capacity (in square feet)* up to 185.8 square meters (2,000 sq. ft.)
Maximum BTUs per Hour (Cord Wood Calculation) 72,400
Maximum Burn Time Up to 10 Hours
* Heating capacity will vary depending on the home's floor plan, degree of insulation, and the outside temperature.
It is also affected by the quality and moisture level of the fuel.
Dimensions
(a) Side, rear and corner clearances are measured from the stove top.
(b) Rubber-Tipped Leveling Bolts (at each corner).
Emissions
Appliance Emission Factor Burning Hardwood: 0.8 g/Kg
Overall Average Efficiency Burning Hardwood: 65%
a
33.5"
851mm
20.25"
515mm
1.5"
39mm
28"
712mm
5"
127mm
b
6" Dia.
152mm
a
31"
788mm
20.25"
515mm
1.5"
39mm
28"
712mm
b
6" Dia.
152mm
5"
127mm

Stove Installation (for qualified installers only) 7
© Travis Industries 100-01438 4160303
SAFETY NOTICE:
Please read this entire manual before you install and use your new room heater.
Failure to follow instructions may result in property damage, bodily injury, or even
death. Contact local building or fire officials about restrictions and installation
inspection requirements in your area.
Planning the Installation
We suggest that you have an authorized Travis Industries dealer install your stove. If you install the
stove yourself, your authorized dealer should review your installation plans.
Check with local building officials for any permits required for installation of this stove and notify your
insurance company before proceeding with installation.
The location of your wood heater in your home will decide how effectively the heat produced will spread
throughout your house. Attention to the home design with consideration of natural convection and air
circulation should be taken into account when choosing the placement of your heater within the home.
Preparation for Installation
Make sure the baffles are in place.
Check for damage to the exterior of the stove (dents should be reported, scratches can be fixed by
applying touch-up paint).
Check the interior of the firebox (replace any cracked firebricks and make sure the baffle is in place).
The stove can be lightened by removing the firebricks - replace before operation.
Packing List
Wood moisture meter
Bypass Tool
Ash Dump Tool
Igniter Cover Plate and Cover Box

8 Stove Installation (for qualified installers only)
303061483410-001seirtsudnIsivarT©
Floor Protection Requirements
Floor protection must extend to the sides, rear, and front of the stove (see “Clearances” below for
minimum floor protection).
Floor protection must be non-combustible and have a thermal resistance equal to 9mm Bellis Board.
Stove Placement Requirements
Clearances may be reduced by methods specified in NFPA 211, listed wall shields, pipe shields, or
other means approved by local building or fire officials.
Stove must be placed so that no combustibles are within, or can swing within 914mm (36") of the
front of the stove (drapes, doors, etc.)
Must maintain the clearances to combustibleslisted below (drywall, furniture)
The stove requires an air source to operate. Combustion air starvation will result in poor performance
or smoke in the house.
Clearances
The following clearances must be met
dleihSeulFhtiWecnaraelCmuminiM
mm523evotsotllawediSA
B Back wall to stove 200 mm
C Corner wall to stove 100 mm
mm003htraehtnorFD
mm002htraehediSE
mm002htraehkcaBF
AUSTRALIAN FLUE KIT REQUIREMENTS:
The above clearances are in accordance to the following:
The heater is to be installed with a 150mm/6” Stainless Steel triple skin (default) flue kit (fitted with heat
shields see below) which conforms to the requirements of the joint AS/NZS 2918:2001 Standard,
Appendix, with respect to the rear wall, side wall, floor and ceiling surface temperatures, when tested in
the positions shown.
Heat Shield Options:
1. 200mm/8” Decorative Mesh, up into the drop box, with the 1
st length (900mm) to have a solid back.
2. Stainless Steel ½ Heat Shield 900mm minimum length x 180 degrees.
.xobpordehtotnipuepipeulf,detalitnevmm002.3

Stove Installation (for qualified installers only) 9
© Travis Industries 100-01438 4160303
Chimney Connector Requirements
Chimney connector is required from the flue collar of the stove to the factory-built chimney or
masonry chimney.
The chimney connector must be 152mm (6”) diameter and a minimum 24 gauge black steel, or one of
the reduced-clearance connectors listed on page 8.
NOTE: Aluminum or galvanized steel is not allowed – these materials cannot withstand the flue
temperatures and may give off toxic fumes when heated.
The chimney connector may not pass through a ceiling, attic, roof, closet, or any other concealed
space (use listed UL 103 HT chimney – see “Chimney Requirements for details). DO NOT USE
CONNECTOR PIPE AS CHIMNEY.
The chimney connector should be as short and direct as possible. No more than 180oof elbows (up to 4
45° elbows) may be used for the entire system (connector and chimney). Horizontal runs should slope
upwards 6mm (1/4”) per foot and be a maximum 914mm (36”) long.
The chimney connector must be installed with the crimped end pointing downwards. This prevents
creosote from leaking to the exterior of the pipe.
The chimney connector must be fastened to the stove and each adjoining section (and chimney).
Standard residential installations with reduced clearance connector may use the clearance determined
by the manufacturer of the connector for the connector to wall clearance or the clearance listed in this
manual. Offsets must be used to maintain the stove to wall clearance.

10 Stove Installation (for qualified installers only)
© Travis Industries 100-01438 4160303
Chimney Requirements
DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY AIR DISTRIBUTION DUCTWORK
UNLESS SPECIFICALLY APPROVED FOR SUCH INSTALLATIONS
IN CANADA: This appliance must be connected to a factory-built chimney conforming to CAN/ULC-
S629, Standard for 650°C Factory-Built Chimneys.
UL 103 HT Chimney must be used from the first ceiling or floor or wall penetration to the chimney
cap.
Use 152mm (6") diameter type UL 103 HT chimney from one manufacturer (do not mix brands) or
code approved masonry chimney with a flue liner.
Chimney must be fastened to each adjoining section.
Follow the chimney manufacturer's clearances and requirements.
Use the chimney manufacturer's fire stops, attic guards, roof supports, and flashings when passing
through a ceiling and roof (see “b” and “d” below).
No more than 180oof elbows (up to 4 45° elbows) may be used for the entire system (connector and
chimney).
NOTE: Additional elbows may be allowed if draft is sufficient. Whenever elbows are used the draft is
adversely affected. Additional chimney height may be required to boost draft.
(a) Min. System Height 4.5 meters (15’)
Max. System Height 10.058 meters (33’)
(b) Roof Penetration and Termination (see
chimney manufacturer’s requirements)
(c) Chimney Sections
(d) Ceiling Penetration (see chimney
manufacturer’s requirements)
(e) Minimum air space to combustibles (see
chimney manufacturer’s requirements –
typically 51mm (2”)
(f) Connector – see “Chimney Connector” on the
previous page.
Figure 1
Drafting Performance
This appliance relies upon natural draft to operate. External forces, such as wind, barometric pressure,
topography, or factors of the home (negative pressure from exhaust fans, chimneys, air infiltration, etc.) may
adversely affect draft. Travis Industries cannot be responsible for external forces leading to less than optimal
performance.











}
}

}
a
b
c
de
f
f
b

Stove Installation (for qualified installers only) 11
© Travis Industries 100-01438 4160303
Chimney Termination Requirements
Must have an approved cap (to prevent water from entering)
Must not be located where it will become plugged by snow or other material
Must terminate at least 914mm (3') above the roof and at least 610mm (2') above any portion of the
roof within 3.048 meters (10') (see Figure 2)
Figure 2
Outside Air Requirements
Must not be drawn from an enclosed space (garage, unventilated crawl space)
Requires a 76.2mm (3”) duct that attaches to the back of the stove (see “a” below).
Outside air duct must have a rodent screen and rain hood (see “b” below).
The Travis Industries Outside Air Kit (SKU 99200139) includes all the above components.
Slanted Roofs
Flat Roofs




Chimney must
extend 3'
above the roof

Chimney must extend 2'
above any portion of the roof
within 10' of the chimney



Chimney must
extend 3'
above the roof
Chimney must extend 2'
above any portion of the roof
within 10' of the chimney

b
a

12 Stove Installation (for qualified installers only)
© Travis Industries 100-01438 4160303
Standard Ceiling
with a Factory-
Built Chimney
Figure 3
Cathedral Ceiling
with a Factory-
Built Chimney
Figure 4
Chimney Cap
(See the section "Chimney
Termination Requirements"
for more details)









Chimney Sections
Minimum Air Space to
Combustibles (See
Chimney Manufacturer's
Instructions)
Chimney Connector Sections
Follow the chimney
manufacturer's instructions
and clearances for roof
penetrations. A storm collar
and flashing are required
(some require a radiation
shield).
}
}
Stove Clearances
(See the section "Stove
Placement Requirements"
for more details)
Floor Protection
(See the section "Floor
Protection Requirements"
for more details)
Follow the chimney
manufacturer's instructions
and clearances for floor
penetrations. A ceiling
support is required, an attic
insulation shield is required
where insulation is present.
Insulation
Minimum 15'
(4.57M)
Maximum 33'
(10.05M)
Chimney Cap
(See the section "Chimney
Termination Requirements"
for more details)







Chimney Sections
Minimum Air Space to
Combustibles (See Chimney
Manufacturer's Instructions)
Follow the chimney
manufacturer's instructions
and clearances for roof
penetrations. A storm
collar, flashing, and
cathedral-style chimney
support are required
(some require a radiation
shield).
}
Minimum 15'
(4.57M)
Maximum 33'
(10.05M)
Stove Clearances
(See the section "Stove
Placement Requirements"
for more details)
Floor Protection
(See the section "Floor
Protection Requirements"
for more details)
Chimney
Connector
Sections

Stove Installation (for qualified installers only) 13
© Travis Industries 100-01438 4160303
Exterior Factory-Built Chimney
A vertical rise of 1.8796 meters (74”) of chimney connector is required, measured from the floor, before
entering a Class ‘A’ wall penetration. For those wishing to pass the chimney through the lower wall, a
NFPA 211 wall pass-through may be used (if approved by local building codes).
Wall Penetrations Under 1.8796 meters (74”)
In cases where the chimney connector must be passed through a combustible wall or partition under
1.8796 meters (74”), the following NFPA 211 method may be used if local building codes permit. Check
with local authorities before installation to insure all necessary requirements have been met. Figure 12
details a wall pass-through based on the NFPA 211 standard. After the pass-through, Class A Chimney
may be used in accordance with the chimney installation instructions.
Figure 5
NFPA 211 Wall Pass-Through
(see NFPA 211 for a full description)
12 Min.
12 Min.
Combustible Materials
Brick
Fire Clay Thimble

14 Stove Installation (for qualified installers only)
© Travis Industries 100-01438 4160303
Hearth Stove
Installation
NOTE:
This type of installation
requires a full reline
(positive connection).
Interior or Exterior
Masonry Chimney
NOT ALLOWED IN
CANADA UNLESS FULL
RELINE IS USED>.
NOTE:
This type of installation
requires a UBC approved
masonry connector or
other method approved by
the NFPA 211 Standard.
See Chimney Connector
Requirements on page 9
for further details.
WARNING:
We strongly recommend a
full reline (positive
connection) when venting
through a masonry
chimney. We also
recommend that a
minimum 914.1mm (3’)
chimney be added to the
minimum system height
for every 304.8mm (1’) of
horizontal run.
NOTE: The entire fireplace and
chimney must be clean, undamaged,
and meet all local building codes (UBC,
etc.). Damage must be repaired prior to
installation. The chimney must be 15'
to 33' tall.
Combustible
Mantle
Min. 36"
Floor Protection (See the
section "Floor Protection
Requirements" for more
details)
Cap and flashing prevents
water from entering.
The liner must be
stainless steel connector
or flexible vent. Follow
the liner manufacturer's
instructions for installation
and support.
Airtight Insulated
Clean-Out
Remove damper or
wire it open
See the section "Stove
Placement
Requirements" for
minimum clearances
required.
NOTE: the chimney must
have a clay tile liner. If it does
not, the installation must use
a positive connection (full
reline). The entire fireplace
and chimney must be clean,
undamaged, and meet all
local building codes (UBC,
etc.). Damage must be
repaired prior to installation.
The chimney must be 15’
(4.57M) to 33’ (10.05M) tall.
See section “Stove Placement
Requirements” for minimum
clearances required.
Min. 18”
(457mm)
clearance to
ceiling
Chimney connector sections
See the section
“Floor Protection
Requirements”
Clay Liner
This type of
installation
requires a
UBC
approved
masonry
connector or
a factory built
(U.L. Listed)
wall thimble.
Make sure
the clean-out
seals in
place.
Full Reline

Operating Your Appliance 15
© Travis Industries 100-01438 4160303
Safety Notice
If this appliance is not properly installed, a house fire may result. For your safety, follow the installation
directions. Contact local building or fire officials about restrictions and installation inspection
requirements in your area.
Read and follow all of the warnings on pages 4 and 5 of this manual.
Do not operate this stove with the ash pan door open.
A fire hazard will result.
Before Your First Fire
Verify the Installation:
Before starting the stove, verify that the stove is properly installed and all of the requirements in this
manual have been followed.
Keep all flammable materials 914mm (36") away from the front of the stove (drapes, furniture, clothing, etc.).
Curing the Paint
Follow the steps below to cure the paint (first fire):
a) Open doors and windows in the room to ventilate the heater during the
curing process.
b) Vacate the room. The fumes from the initial heating process are non-toxic
but may be unpleasant.
c) Slowly bring the heater to a medium burn (400°F/204°C) for 45 minutes.
Then increase the burn temperature to a hot burn (600°F/315°C) for an
additional 45 minutes. This will cure the paint.
Door Gasket - The door gasket can adhere to the paint on the front of the
heater. To prevent this, carefully open and close the door a few times during
the paint curing process.
Carbon Monoxide (CO) Emissions
Smoke from wood heaters contain CO. This gas is an indication of incomplete combustion and is
detrimental to the environment and to your health. The more visible the smoke, the higher the CO levels.
Burning dry wood is the most significant step you can take to reduce CO emissions. It is also important to
understand the combustion process so you can burn your heater efficiently. Read the manual thoroughly
so that you can operate your heater in the most efficient and clean manner possible.
Over-Firing the Stove
DO NOT OVERFIRE THIS HEATER: Attempts to achieve heat output rates that exceed heater design
specifications can result in permanent damage to the heater.
This stove was designed to operate at a high temperature. But due to differences in vent configuration,
fuel, and draft, this appliance can be operated at an excessive temperature. If the stove top or other area
starts to glow red, you are over-firing the stove. Shut the air control down to low and allow the stove to
cool before proceeding.
If you are uncertain of over-firing conditions, we suggest placing a stove thermometer (e.g. Rutland®
Model 710) directly in front of the flue outlet on the stovetop temperatures exceeding
800°F/426.667°C are generally considered over-firing and will void the warranty.








2 to 4 hours

16 Operating Your Appliance
© Travis Industries 100-01438 4160303
Opening the Door
The door becomes hot during use. Use a glove to open the door if the handle is hot.
Do not operate this stove with the door open. A fire hazard will result.
To prevent smoke from entering the room, open the air control and bypass (see instructions below)
before opening the door. You can also open the door a small amount and let air enter the firebox to
equalize the pressure, and then open the door fully.
Bypass Operation
The bypass controls the flow of smoke inside the heater. When pulled out, smoke goes directly up the
flue, creating more draft. When pushed in, the smoke goes around the baffle, utilizing the secondary
combustion and making the heater more efficient.
When re-loading, pull the bypass out.
During normal operation, push the bypass in.
Bypass Pushed In
Used for normal operation
Bypass Pulled Out
Used for starting and re-loading










Use the included pull tool
to operate the bypass rod

Operating Your Appliance 17
© Travis Industries 100-01438 4160303
Starting a Fire
Use of the optional GreenStart igniter will greatly simplify this process. See page 36.
Since the dawn of time man has debated the best way to start a fire. Some use the boy-scout "tee-pee"; some
prefer the "tic-tac-toe" stack. Either way, review the hints and warnings below to ensure proper fire starting.
Make sure the air control is open (pulled out). If additional air is needed, open the door 6.35mm
(1/4") during the first five minutes of startup.
Make sure the bypass is pulled out.
Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start
or "freshen up" a fire in this stove. Keep all such liquids well away from the stove while it is in use.
DO NOT USE CHEMICALS OR FLUIDS TO START THE FIRE. DO NOT BURN GARBAGE OR
FLAMMABLE FLUIDS SUCH AS GASOLINE, NAPHTHA OR ENGINE OIL. Do not place such fuel
within space heater installation clearances or within the space required for charging and ash removal.
If using a fire-starter, use only products specifically designed for stoves - follow the manufacturer's
instructions carefully.
HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT
MAY CAUSE SKIN BURNS.
Do not open the ash pan when the stove is lit. An extreme fire hazard will result.
If the smoke does not pass up the chimney, ball up one sheet of newspaper, place it in the center of the
firebox and light it. This should start the chimney drafting (this eliminates "cold air blockage").
Use plenty of kindling to ensure the stove reaches a proper temperature. Once the kindling is burning
rapidly, place a few larger pieces of wood onto the fire.

18 Operating Your Appliance
© Travis Industries 100-01438 4160303
Adjusting the Burn Rate
Use the air control slider to control the burn rate of the stove. See the illustration below for details.
Approximate Air Control Settings Overnight Burn Fully In
Medium Low Burn 5mm Out
Medium High Burn 10mm Out
High Burn Fully Out
The air control becomes hot during operation - use gloves or a tool to prevent burns.
The air control may take several minutes to influence the burn rate. When making adjustments, you
may wish to let the stove burn for 10 minutes to gauge performance.





Operating Your Appliance 19
© Travis Industries 100-01438 4160303
Understanding Your Heater’s Combustion System
This heater uses a dual combustion system detailed below:
Primary Combustion: This is the combustion (fire) that takes place directly on the wood. Primary combustion
determines how fast the fire burns. Air for primary combustion is supplied through the air control. When you
adjust the air control you control the amount of air that reaches the fire and creates primary combustion. The air
control supplies air to the air wash (the air holes above the door opening – used to help clean the glass) and
through the pilot orifice (center bottom of the door opening). By using the air control, and supplying air through
these two openings, you control primary combustion.
Secondary Combustion: This is the combustion (fire) that does not contact the wood. Secondary combustion
burns the visible emissions or smoke that is not consumed during primary combustion. During some phases of
combustion you will see secondary combustion. It appears as a glowing flame at the top of the firebox. Air for
secondary combustion is supplied by the air tubes at the top of the firebox.
Items to Consider:
During medium and high burn rates the stove will manage secondary and primary combustion on its own.
When the heater is set to a low burn rate more care is needed to ensure the secondary combustion system
works properly. Make sure the stove is hot and a good coal bed is established before adjusting your heater to
low burn.
Understanding the combustion system in this heater will help minimize the visible emissions this heater
releases into the environment. The primary pilot orifice at the center bottom of the door opening is designed to
help the secondary combustion at low burn settings. The pilot provides a small amount of air that burns up
through the fuel load providing the heat and flame needed for the secondary system to ignite. The air tubes
under the baffle need to remain ignited for low burns to be effective.
As you load your heater for a low burn, take care in placing the wood. This will affect how well your
secondary system works as the wood is consumed. Do not block the pilot orifice. Stack wood so the pilot air
can burn its way up between the pieces, helping your heater burn effectively throughout the low fire. This will
reduce the visible emissions your heater produces and increase the amount of heat you get from the wood. If
you are unsure how well your heater is burning look at the chimney cap to monitor visible emissions.
Burning Your Heater
Starting a Fire: When starting a fire it is imperative to get the heater hot and drafting as quickly as possible.
This promotes combustion and reduces emissions. There are many ways to start a fire and you will become adept
as you become familiar with the way your heater burns. Before you start, make sure your burn rate setting (air
control) is all the way open and the by-pass (if equipped) is open. We suggest that you use a layer of crumpled
newspaper covered with three layers of small kindling, stacked tic tac toe style with approximately 12.7mm-
25.4mm (½”-1”) gaps between them. Continue to layer wood on top of the kindling with the same air gaps using
slightly bigger pieces increasing in size as you stack upward with the final layer being 76.2-127mm (3-5”)
diameter pieces loaded on the top. This should fill the firebox. Light the newspaper in several places near the
door opening. Shut the door but do not latch it, creating a small opening to allow air to feed the kindling fire. Never
leave your heater unattended if your door is not latched shut. While the kindling burns the fire will heat and ignite
the larger pieces above. Once the whole load is burning shut and latch the door leaving the burn rate on high.
Depending on your heater, the chimney, and the outside environment, you may need to leave your bypass open
for up to 20 minutes after lighting the fire. If the fire dies when you shut the bypass you will need to leave it open
longer. The presence of a hot coalbed is critical to good combustion. We cannot overstate the importance of a
hot coal bed before slowing your burn rate or re-loading your heater. We recommend that you allow the first
ignition load of wood to burn through at the high burn rate. This will get your heater up to temperature and
establish a coal bed.
Reloading: When reloading a hot heater set the burn rate on high for at least 15 min before slowing it down.
Low Burn: If preparing for an overnight or low burn a longer heat up period may be necessary. Reload the
heater full of wood making sure there are air gaps between the wood pieces so the pilot air can burn up through
the middle load keeping the secondary combustion system hot and active throughout the burn. After loading, burn
the heater on high for at least 15 minutes before setting the air control to low. Excessive creosote buildup (or
sooting) in the heater at the end of a low burn signifies that the heater was not hot enough and the wood load was
not burned long enough on high after loading before shutting down the air control.

20 Operating Your Appliance
© Travis Industries 100-01438 4160303
Ash Removal
Whenever ashes get 76.2-101.6mm (3 to 4) inches deep in your firebox or ash pan, and
when the fire has burned down and cooled, remove excess ashes. Leave an ash bed
approximately 1inch deep on the firebox bottom to help maintain a hot charcoal bed. Let the
stove cool completely before removing ashes (wait at least two hours after the last coal has
extinguished). Ashes should be placed in a metal container with a tight-fitting lid. The closed
container of ashes should be placed on a noncombustible floor or on the ground, away from
all combustible materials, pending final disposal. The ashes should be retained in the closed
container until all cinders have thoroughly cooled.
Improperly disposed ashes lead to fires. Hot ashes placed in cardboard boxes, dumped in back yards,
or stored in garages, are recipes for disaster.
Wood-burning stoves are inherently dirty. During cleaning have a vacuum ready to catch spilled ash
(make sure ash is entirely extinguished).
There are vacuum cleaners specifically made to remove ash (even if the ash is warm). Contact your
dealer for details.
Ash Pan
Do not operate this stove with the ash pan door open. A fire
hazard will result.
The ash pan must be properly inserted and fully closed during operation. Failure to fully close and
seal the ash pan may lead to an over-fired stove, negating the warranty and creating a safety hazard.
Ashes must only be dumped into the ash pan only after the stove has fully cooled and all embers are
extinguished.
Moving Ashes to the Ash Dump
This stove is equipped with an ash dump tool. It is stored on the hook a the back of the stove (see
pictures below). NOTE: The tool will become hot when the stove is in use.
Use the included tool to lift the ash dump from the floor of the firebox (there are two – use either or both).
Then scrape the ashes into the ash dump. NOTE: This tool is only designed for use with the ash dump
(do not use it as a poker or to position wood).
ASHES