Lopi Sweet dreams User manual

Featuring the Burner

• Direct Vent Freestanding Stove

• Natural Gas or Propane

• Vent Horizontally or Vertically

• Standard Residential

• Mobile Home Approved

Tested and Listed by

OMNI-Test Laboratories, Inc.

Beaverton, Oregon

Report # 028-S-55-5

ANSI Z21.88

WARNING: If the information in these instructions is not followed exactly, a fire or

explosion may result causing property damage, personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or

any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the

gas supplier.

This appliance may be installed in an aftermarket permanently located, manufactured

home (USA only) or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases unless a certified kit is used.

Sweet Dreams Manual

Installer: After installation give this manual to the home-owner

and explain operation of this heater.

Mukilteo, WA 98275

2Introduction

Travis Industries 100-01155 4040903

Introduction

We welcome you as a new owner of a Lopi Sweet Dreams stove. In purchasing a Sweet Dreams you

have joined the growing ranks of concerned individuals whose selection of an energy system reflects

both a concern for the environment and aesthetics. The Sweet Dreams is one of the finest home

heaters the world over. This manual will explain the installation, operation, and maintenance of this

stove. Please familiarize yourself with the Owner's Manual before operating your heater and save the

manual for future reference. Included are helpful hints and suggestions that will make the operation

and maintenance of your new stove an easier and more enjoyable experience. We offer our continual

support and guidance to help you achieve the maximum benefit and enjoyment from your heater.

Important Information

No other Sweet Dreams Stove has the same serial

number as yours. The serial number is on the listing

plate chained to the gas control valve.

This serial number will be needed in case you require

service of any type.

Model: Lopi Sweet Dreams Stove

Serial Number:

Purchase Date:

Purchased From:

Mail your Warranty Card

Today, and Save Your Bill of

Sale.

To receive full warranty coverage,

you will need to show evidence of

the date you purchased your

heater. Do not mail your Bill of

Sale to us.

We suggest that you attach your

Bill of Sale to this page so that you

will have all the information you

need in one place should the need

for service or information occur.

Table of Contents 3

Travis Industries 100-01155 4040903

Introduction

Introduction & Important Information................2

Safety Precautions

Safety Precautions......................................4

Features & Specifications

Features ....................................................6

Installation Options......................................6

Heating Specifications..................................6

Dimensions.................................................6

Installation

Installation Warning......................................7

Packing List................................................7

Additional Items Required for Installation..........7

Installation Overview....................................7

Installation Hints..........................................8

Stove Clearances ........................................8

Mobile Home Requirements............................8

Heater Placement Requirements.....................9

Floor Protection Requirements........................9

Gas Line Installation.....................................10

Vent Requirements.......................................11

Altitude Considerations ............................11

Vent Clearances .....................................11

Part Numbers for 8” Vent...........................12

Vent Installation......................................12

Approved Vent Configurations........................13

Restrictor Position...................................13

Diffuser Plate .........................................13

Vertical Terminations ...............................14

Horizontal Terminations – LP (Propane) .......15

Horizontal Terminations – NG (Natural Gas)..16

Horizontal Term. with 45° Elbow (NG or LP)...17

Vent Termination Requirements ......................18

Finalizing the Installation

Stove Top and Face Removal .........................19

Glass Frame Removal...................................20

Log Installation............................................22

Purge Gas & Leak Test .................................24

Pilot Adjustment (if necessary).......................24

Air Shutter Adjustment (if necessary)...............24

Check Flame...............................................25

Explain Operation to Home Owner ...................25

Operation

Before You Begin.........................................26

Location of Controls .....................................26

Starting The Pilot .........................................27

Starting the Stove for the First Time.................28

Turning the Stove On and Off .........................28

Adjusting the Flame Height.............................28

Adjusting the Blower Speed (optional) ..............29

Normal Operating Sounds..............................29

Normal Operating Odors................................29

Maintenance

Maintaining Your Stove’s Appearance..............30

Yearly Service Procedure..............................30

Troubleshooting Table...................................31

How this Stove Works...................................32

What Turns the Main Burners On and Off......32

What Prevents Gas Buildup.......................32

Wiring Diagram ............................................33

Replacement Parts List.................................33

Safety Label

Safety (Listing) Label....................................34

Warranty

Warranty....................................................35

Optional Equipment

Optional Accessories...................................36

LP Conversion Kit ........................................37

Blower .......................................................40

Leg Mounting Kit..........................................43

Index

Index.........................................................44

4Safety Precautions

Travis Industries 100-01155 4040903

• IF YOU SMELL GAS:

* Do not light any appliance

* Extinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire

department

• This unit must be installed by a qualified installer to prevent the

possibility of an explosion. Your dealer will know the requirements in

your area and can inform you of those people considered qualified.

The room heater should be inspected before use and at least annually

by a qualified service person. More frequent cleaning may be

required due to excessive lint from carpeting, bedding material, etc.

• The instructions in this manual must be strictly adhered to. Do not use makeshift

methods or compromise in the installation. Improper installation will void the warranty

and safety listing.

For LPG only | Pout 11” W.C.

Look for this label:

If the label is present, the

heater is equipped for LP

(propane). If the label is

absent, the heater is equipped

for NG (natural gas).

•This heater is either approved for natural

gas (NG) or for propane (LP or LPG).

Burning the incorrect fuel will void the

warranty and safety listing and may cause

an extreme safety hazard. Direct

questions about the type of fuel used to

your dealer. Check for the label shown to

the right.

•Contact your local building

officials to obtain a permit

and information on any

installation restrictions or

inspection requirements in

your area. Notify your

insurance company of this

heater as well.

•If the flame becomes sooty,

dark orange in color, or

extremely tall, do not

operate the heater. Call

your dealer and arrange for

proper servicing.

•It is imperative that control

compartments, screens, or

circulating air passageways

of the heater be kept clean

and free of obstructions.

These areas provide the air

necessary for safe

operation. ?•Do not operate the heater if

it is not operating properly in

any fashion or if you are

uncertain. Call your dealer

for a full explanation of your

heater and what to expect.

Gas

•Do not store or use gasoline

or other flammable liquids in

the vicinity of this heater.

AAAA

•Do not use this appliance if

any part has been under

water. Immediately call a

qualified service technician

to inspect the appliance and

to replace any part of the

control system and any gas

control which has been

under water.

Safety Precautions 5

Travis Industries 100-01155 4040903

•Do not place clothing or

other flammable items on or

near the heater. Because

this heater can be controlled

by a thermostat there is a

possibility of the heater

turning on and igniting any

items placed on or near it.

•Light the heater using the

built-in piezo igniter. Do not

use matches or any other

external device to light your

heater.

•Never remove, replace,

modify or substitute any part

of the heater unless

•The viewing glass should be

opened only for lighting the

pilot or conducting service.

Do not operate with cracked,

broken, or removed glass.

•Any safety screen or guard

removed for servicing must

be replaced prior to

operating the heater.

instructions are given in this

manual. All other work must

be done by a trained

technician. Don't modify or

replace orifices.

•Allow the heater to cool

before carrying out any

maintenance or cleaning.

•Operate the heater

according to the instructions

included in this manual.

•If the main burners do not

start correctly turn the gas

off at the gas control valve

and call your dealer for

service.

•The pilot flame must contact

the thermopile and

thermocouple (see the

illustration to the left). If it

does not, turn the gas

control valve to "OFF" and

call your dealer.

•This unit is not for use with

solid fuel

•Do not place anything inside

the firebox (except the

included fiber logs).

•If the fiber logs become

damaged, replace with

Travis Industries log set.

This

Manual

•Do not throw this manual

away. This manual has

important operating and

maintenance instructions

that you will need at a later

time. Always follow the

instructions in this manual.

•Children and adults should

be alerted to the hazards of

high surface temperature

and should stay away to

avoid burns or clothing

ignition. Young children

should be supervised when

they are in the same room as

the heater.

• Plug the heater into a

120V grounded electrical

outlet. Do not remove the

grounding plug.

• Don’t route the electrical

cord in front of, over, or

under the heater

•Instruct everyone in the

house how to shut gas off to

the appliance and at the gas

main shutoff valve. The gas

main shutoff valve is usually

next to the gas meter or

propane tank and requires a

wrench to shut off.

•Travis Industries, Inc.

grants no warranty,

implied or stated, for

the installation or

maintenance of your

heater, and assumes

no responsibility of any

consequential

damage(s).

6Specifications

Travis Industries 100-01155 4040903

Features:

- Ember Fyre™ Burner for "Wood Fire" Look

- Works During Power Outages (millivolt system)

- High Efficiency

- Optional Thermostat or Remote Control

- Optional Blower for Quicker Heat Distribution

- Convenient Operating Controls

- Variable-Rate Heat Output

- Low Maintenance

Installation Options:

- Freestanding Stove

- Horizontal or Vertical Vent

- Residential or Mobile Home

- Straight or Corner Placement

- Bedroom Approved

Heating Specifications:

Approximate Heating Capacity (in square feet)*..............................Up to 850 with optional blower, 650 without

Maximum BTU Input Per Hour.......................................................16,500

Minimum BTU Output on Low ......................................................10,500 (NG) 9,380 (LP)

Steady State Efficiency** (with optional blower on).........................up to 77.2% (NG) up to 74.5% (LP)

AFUE (Annual Fuel Utilization Efficiency).......................................63% (NG) 60.7% (LP)

• Heating capacity will vary depending on the home’s floor plan, degree of insulation, and the outside temperature.

** Efficiency rating is a product of thermal efficiency rating determined under continuous operation independent of

installed system.

Dimensions & Weight:

14-3/4"

36-1/2"

45-1/4" Leg Kit

15-1/16"

23-1/4"

28-5/8"

37-3/8" Leg Kit

1-5/8"

Weight: 310 Lbs.

Electrical Specifications (for optional blower)

Electrical Rating.........................................................115 Volts, 1.3 Amps, 60 Hz (150 watts on high)

Fuel:

This heater is shipped in natural gas (NG) configuration but may be converted to propane (LP) using

the included LP conversion kit. The sticker on top of the gas control valve will verify the correct fuel.

Installation (for qualified installers only) 7

Travis Industries 100-01155 4040903

Installation Warnings:

! Failure to follow all of the requirements may result in property damage, bodily

injury, or even death.

! This heater must be installed by a qualified installer who has gone through a

training program for the installation of direct vent gas appliances.

! This appliance must be installed in accordance with all local codes, if any; if not,

follow ANSI Z223.1 and NFPA 54(88).

! In Manufactured or Mobile Homes must conform with Manufactured Home

Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a

standard is not applicable, the Standard for Manufactured Home Installations,

ANSI/NCSBCS A225.1. This appliance may be installed in Manufactured Housing

only after the home is site located.

! This stove is designed to operate on natural gas or propane (LP).

! All exhaust gases must be vented outside the structure of the living-area.

Combustion air is drawn from outside the living-area structure.

! Notify your insurance company before hooking up this stove.

! The requirements listed below are divided into sections. All requirements must be

met simultaneously. The order of installation is not rigid – the qualified installer

should follow the procedure best suited for the installation.

Packing List

• Propane Conversion Kit

• Log Set

• Glass Latch Tool (to un-latch glass frame)

Additional Items Required

• Vent (see “Venting Requirements” for details)

• Gas Line Equipment (shutoff valve, pipe, etc.)

Installation Overview

AAAAAAAAAAAAAAAAAAAA

See "Vent

Requirements"

See "Floor

Protection

See "Gas

Line

Installation"

AAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAA

See

"Clearances"

8Installation (for qualified installers only)

Travis Industries 100-01155 4040903

Installation Hints:

• If converting to LP, convert the appliance prior to installation.

• If using the optional blower, install it prior to installation.

• Install the logs last - they are fragile.

• When determining the location of the stove, locate the wall studs (for horizontal penetrations) and

ceiling trusses (for vertical penetrations). You may wish to adjust the stove position slightly to ensure

the vent does not intersect with a framing member.

• Fumes and smoke from the paint curing and oil burning off the steel may occur the first time you start

this heater. This is normal. We recommend you open windows to vent the room.

Stove Clearances

3" Min.

1" Min.

Straight Installations Corner Installations

Measure stove

clearances to the

stove top.

45°

1" Min.

45°

Mobile Home Requirements

•When the stove is installed in a mobile home, it must be bolted to the floor (use the leg mounting kit

with or without legs) and the appliance grounded (use the optional blower with a grounded circuit or

other suitable grounding method - current ANSI/NFPA 70).

Installation (for qualified installers only) 9

Travis Industries 100-01155 4040903

Heater Placement Requirements

•Heater must be installed on a level surface capable of supporting the heater and vent

•Due to high temperatures, the appliance should be located out of traffic and away from furniture

and draperies.

•When placed in a location where the floor to ceiling height is under 7 feet, the installation is

considered an alcove and must meet the following requirements:

-The alcove floor to ceiling height must be at least 12”above the stove top

-The alcove must not be more than 30”deep before the ceiling returns to 7’

-The alcove must be at least 29-1/2”wide

•The heater must not be placed so the vents below or above the door, along the sides of heater, or

along the back of the heater can become blocked.

•This heater may be placed in a bedroom. Please be aware of the large amount of heat this

appliance produces when determining a location.

Floor Protection Requirements

•The stove may be placed directly on the floor (wood, carpet, linoleum, etc.). However, we

strongly recommend using floor protection under the stove (made of wood, tile, etc.)

when installing on carpet or linoleum to prevent heat from dis-coloring the surface.

10 Installation (for qualified installers only)

Travis Industries 100-01155 4040903

Gas Line Installation

MASSACHUSETTS INSTALLATIONS - WARNING:

THIS PRODUCT MUST BE INSTALLED BY A LICENSED PLUYMBER OR GAS FITTER WHEN INSTALLED WITHIN THE

COMMONWEALTH OF MASSACHUSETTS.

OTHER MASSACHUSETTS CODE REQUIREMENTS:

• Flexible connector must not be longer than 36 inches.

• Shutoff valve must be a “T”handle gas cock.

• Only direct vent sealed combustion products are approved for bedrooms or bathrooms.

• Fireplace dampers must be removed or welded in the open position prior to the installation of a fireplace insert or gas log.

!The gas line must be installed in accordance with all local codes, if any; if not, follow current ANSI

Z223.1 or NFPA 54.

!The heater and gas control valve must be disconnected from the gas supply piping during any

pressure testing of that system at test pressures in excess of 1/2 psig (3.45 kPA). For pressures

under 1/2 psig (3.45 kPA), isolate the gas supply piping by closing the manual shutoff valve.

•This heater is designed for natural gas but can be converted to propane. Check the sticker on top

of the gas control valve to verify the correct fuel is used (see page 4).

•Leak test all gas line joints and the gas control valve prior to and after starting the heater.

•A manual shutoff valve is required for installation (it must be located within 3’of the heater).

T-Handle gas cocks are required in Massachusetts in compliance with code 248CMR.

•The location of the gas inlet is shown below

2-3/4"

Center

Line 7-1/4"

Back of

Stove

The included fitting

accepts a 3/8" M.P.T.

or 1/2" F.P.T.

AAAAAAAA

Gas Inlet Pressure

•With the heater off, the inlet pressure must meet the requirements listed in the table below

•If the pressure is not sufficient, make sure the piping used is large enough and the total gas load

for the residence does not exceed the amount supplied.

•The supply regulator (the regulator that attaches directly to the residence inlet or to the propane

tank) should supply gas at the suggested input pressure listed below. Contact the local gas

supplier if the regulator is at an improper pressure.

Standard Input Pressure

Natural Gas 7”W.C. (1.74 Kpa)

Propane 13”W.C. (3.23 Kpa)

Installation (for qualified installers only) 11

Travis Industries 100-01155 4040903

Vent Requirements

•The vent must maintain the required clearance to combustible materials to prevent a fire (see

“Clearances”below). Do not fill air spaces with insulation.

•The gas appliance and vent system must be vented directly to the outside of the building, and never

be attached to a chimney serving a separate solid fuel or gas-burning appliance. Each direct vent gas

appliance must use it's own separate vent system.

Altitude Considerations

This heater has been tested at altitudes ranging from sea level to 8,000 feet (2,400 M). In this testing we have

found that the heater, with its standard orifice, burns correctly with just an air shutter adjustment.

•Failure to adjust the air shutter properly may lead to improper combustion which can create a safety hazard.

Consult your dealer or installer if you suspect an improperly adjusted air shutter.

Vent Clearances

Min. 2" Clearance Above

45°Sloping Vent

AAAAAA

0" Clearance to the sides

after the first firestop.

AAA

Use a firestop whenever

passing through a

ceiling, enclosure or

floor penetration.

Use a wall thimble (#1247) when

passing through any wall.

Min. 2" Clearance

Above the Vent

1" Clearance Below the Vent

0" Clearance to the side of vent after the

first firestop.

Part Numbers for 8”Diameter Pipe

•Use Model GS Direct Vent manufactured by Simpson Dura-Vent only

. Follow the installation

instructions included with the vent. For the nearest Simpson Dura-Vent supplier, call (800) 835-4429.

Vent part numbers and descriptions are listed below.

Straight Lengths

1208B 6" Pipe Length, Black

1207B 9" Pipe Length, Black

1206B 12" Pipe Length, Black

1204B 24" Pipe Length, Black

1203B 36" Pipe Length, Black

1202B 48" Pipe Length, Black

1211B 11”to 14-5/8" Adjustable Pipe,

Black

Terminations

1285 Horizontal Square Termination

1291 Vert. High Wind Termination

1250 Vinyl Siding Stand-off

Elbows

1245B 45°Elbow, Black

1290B 90°Elbow, Black

Penetration, Support

1247 Wall Thimble

1241 Cathedral Ceiling Support Box

1263 Ceiling Fire-stop

1288 Wall Strap

NOTE:

All measurements are for 8"

diameter vent.

12-3/8" tall

10-3/4" wide with

1-3/4" to 3-3/8" overlap 16-1/4"

1-3/4"

Vent Length

(2', 3', etc.)

NOTE:

Vent sections overlap

each other by 1-3/4"

3-1/2"

Side View

3-1/2"

Vent

Horizontal

Run

Vent

Height

12 Installation (for qualified installers only)

Travis Industries 100-01155 4040903

Vent Installation

•In addition to the requirements below, follow the requirements provided with the vent.

Vertical Termination

(part # 1291)

Use a roof flashing and storm collar

whenever passing through the roof

Vertical Vent

Requirements

Horizontal Vent

Requirements

Minimum framing

for fire stop

0" Clearance on Vertical

Sections to combustible

surfaces.

Use a ceiling firestop whenever passing through a

ceiling (or enclosure and at every floor penetration.

Combustible

Framing

Use a firestop when passing through a wall. Make

sure there is a 2" clearance above the vent.

2" Min.

1" Min.

0" Clearance

Combustible

Surfaces

Minimum framing

for fire stop

Minimum

11" tall

Minimum

8" wide

•Slide the vent sections together and turn 1/4 turn until the sections lock in

place.

•Screws are not required to secure the vent. However, three screws may be

used to secure vent sections together if desired.

•High temperature sealant is recommended at the appliance starter section

connection (use high-temperature silicone or Mill-Pac®).

•If disassembly is required, at time of re-assembly check to see if the vent

creates a tight fit. If it does not, apply high temperature sealant to the joints of

the affected sections.

•Horizontal sections require a 1/4" rise every 12" of travel

•Horizontal sections require non-combustible support every three feet (e.g.: plumbing tape)

Installation (for qualified installers only) 13

Travis Industries 100-01155 4040903

Approved Vent Configurations

Restrictor Position

•A vent restrictor is built

into the appliance to

adjust the flow rate of

exhaust gases. This

ensures proper

combustion for all vent

configurations.

Depending upon the vent

configuration, you may be

required to adjust the

restrictor position. The

charts for acceptable vent

configurations detail the

correct vent restrictor

position.

To Access the Restrictor:

Remove the face (with the stove

cool). You can use the glass

latch tool to move the restrictor.

Determine the correct restrictor position (see the charts under "Approved

Vent Configurations" - the factory position is #1).

Lift up the adjustment plate and move it so the correct notch falls into the

slot on the adjustment bracket.

This restrictor is in position 1

(factory setting).

Adjustment Bracket

Adjustment

Plate

To adjust, lift the adjustment plate and

pull it forward

Restrictor Position

# 7

# 6

etc...

# 2

This restrictor is in position 6.

To Adjust the Restrictor:

Diffuser Plate

•Certain vent configurations require the

diffuser plate to be removed. It is located in

the firebox, behind a baffle above the burner

(remove the firebox liner first). Refer to the

charts for approved vent configurations to

determine if the diffuser plate requires

removal.

Remove the

baffle.

Remove the

diffuser plate.

Replace the screws for the diffuser

plate to seal the holes in the firebox.

Replace the baffle.

1/4" Nutdriver

14 Installation (for qualified installers only)

Travis Industries 100-01155 4040903

Vertical Terminations

•The diffuser must be

removed.

•The termination must fall

within the shaded area

shown in the chart. Use

the indicated restrictor

position.

•If using offsets, use the

table below to calculate the

vertical rise and horizontal

offset

Offset

Length

Horizontal

Offset

Vertical

Rise

Offset Length Hor. Offset Vert. Rise

None 5”1’

1’Section 1’1’7”

2’Section 1’9”2’4”

3’Section 2’5”3’

4’Section 3’2”3’8”

4’+ 1’Section 3’9”4’4”

4’+ 2’Section 4’6”5’

4’+ 3’Section 5’2”5’9”

4’+ 4’Section 6’6’9”

AAAAAAAAAAAAA

5 feet

10 feet

15 feet

20 feet

25 feet

30 feet

0 feet

40' (max)

5 feet

10 feet

0 feet

5 feet

10 feet

14' (max)

15 feet

20 feet

25 feet

30 feet

0 feet

NOTE:

Horizontal sections require a

1/4" rise every 12" of travel.

10 feet

40' (max)

14' (max)

NOTE:

Restrictor positions are

based upon lab tests.

The ideal restrictor

position may vary

slightly, especially when

the termination is near a

demarkation line.

5 feet

NOTE:

One 45°or 90°elbow may

be used between horizontal

sections. Horizontal length

is caculated by adding each

horizontal run together.

35 feet35 feet

Restrictor

Position # 1

Restrictor

Position # 6

Restrictor

Position # 7

6' (min) 6' (min)

NOTE:

Two 45°elbows

may be used.

Installation (for qualified installers only) 15

Travis Industries 100-01155 4040903

Horizontal Terminations – LP (Propane)

•The diffuser must be removed.

• 0 or 2 90°Elbows may be used. See "Horizontal Termination with 45°Elbow" if installing into a corner

application.

•If using a Snorkel Termination (14”or 36”) add the snorkel height to the vertical height (snorkel

terminations are used primarily for basement installations).

•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor

position.

AAAAAAAAAAAA

5 feet

10 feet

0 feet

5 feet

0 feet

10 feet

5 feet

10 feet

14'

(max)

10 feet

Restrictor

Position # 1

14 feet

(max)

NOTE:

Horizontal sections require a 1/4" rise

every 12" of travel.

14 feet

(max) 14 feet

(max)

NOTE:

Restrictor positions are based upon lab tests.

The ideal restrictor position may vary slightly.

16 Installation (for qualified installers only)

Travis Industries 100-01155 4040903

Horizontal Terminations – NG (Natural Gas)

• 0 or 2 90°Elbows may be used. See "Horizontal Termination with 45°Elbow" if installing into a corner

application.

•If using a Snorkel Termination (14”or 36”) add the snorkel height to the vertical height (snorkel

terminations are used primarily for basement installations).

•The termination must fall within the shaded area shown in the chart. Use the indicated restrictor

position.

AAAAAAAAAAAA

5 feet

10 feet

0 feet

5 feet

0 feet

10 feet

5 feet

10 feet

14'

(max)

10 feet

Restrictor

Position # 1

Diffuser

Removed

14 feet

(max)

NOTE:

Horizontal sections require a 1/4" rise every

12" of travel.

NOTE:

Restrictor positions are based upon lab tests.

14 feet

(max) 14 feet

(max)

Restrictor Position # 1

Diffuser Installed

Installation (for qualified installers only) 17

Travis Industries 100-01155 4040903

Horizontal Termination with 45° Elbow (NG or LP)

• This type of installation requires (1) 45° elbow, a maximum 12" of horizontal vent, and the horizontal

termination.

• Use restrictor position # 1.

• When using NG, leave the diffuser installed.

• When uing LP, remove the diffuser.

5 feet

0 feet

5 feet

Restrictor Position # 1

NG = Diffuser Installed

LP = Diffuser Removed

45°Elbow

Maximum 12" Section Termination

18 Installation (for qualified installers only)

Travis Industries 100-01155 4040903

Vent Termination Requirements (see illustration below)

! Venting terminals shall not be recessed into a wall or siding.

A Minimum 9" clearance from any door or window

B Minimum 12" above any grade, veranda, porch, deck or balcony

C Minimum 3-3/8" from outside corner walls

NOTE: Clearance in accordance with local installation codes and the requirements

of the gas supplier.

DMinimum 0" from inside corner walls

11” Min.

6” Min.

Roof

Surface

Roof

Eaves

E Minimum 11" clearance below unventilated soffits or roof surfaces

Minimum 18" clearance below ventilated soffits

Minimum 6" clearance below roof eaves

NOTE: Vinyl surfaces require 24"

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

F Minimum 12" clearance below a veranda, porch, deck or balcony

NOTE: Permitted only if veranda, porch, deck, or balcony is fully open on a minumum of two sides beneath the floor.

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

G Minimum 48" clearance from any adjacent building

H Minimum 84" clearance above any grade when adjacent to public walkways or driveways

NOTE: may not be used over a walkway or driveway shared by an adjacent building

I Minimum 48" clearance from any mechanical air supply inlet

J Minimum 36" clearance above and 48” below and to the sides of non-mechanical air supply inlet

K Minimum 36" from the area above the meter/regulator (vent outlet)

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

L Minimum 36" from the meter/regulator (vent outlet)

NOTE: Clearance in accordance with local installation codes and the requirements of the gas supplier.

M Minimum 12” above the roof line (for vertical terminations)

N Minimum 24” horizontal clearance to any surface (such as an exterior wall) – for vertical terminations

NOTE: Measure clearances to the nearest edge of the exhaust hood.

• Use the vinyl siding standoff (#1250) when installing on an exterior with vinyl siding.

• Vent termination must not be located where it will become plugged by snow or other material

Finalizing the Installation(for qualified installers only) 19

Travis Industries 100-01155 4040903

1Remove the stove top and face following the directions below.

Warning: The appliance must be completely cool prior to removing the top and face.

With both hands, lift

the stove top and

place it aside.

NOTE:

If using the

Aromatherapy

tray, remove it at

this time.

Lift the face and

off of the stove.

Four hooks on the

face insert into the

slots on the stove.

Installation Hint:

Tilt the face back, insert the bottom hooks first, then lift and insert

the top hooks. The face can then be slid down into place.

HINT:

Lift the face from

under the arch -

this allows your

hand to wrap

around the face.

20Finalizing the Installation (for qualified installers only)

Travis Industries 100-01155 4040903

2Remove the glass following the directions below.

Warning: Do not strike or slam the glass.

Note: Verify the gasket (inside the glass frame) is intact and contacts the firebox when installed.

Open the four latches holding the glass

frame in place (start with the two below

the glass) - follow the directions shown

to the right.

Twist 1/4 turn.

The spring pin will

disengage from the

latch bracket,

opening the latch.

Latch Bracket

Insert the 1/4”key

into the spring

pin.

Glass

Top of

Firebox

Spring Pin

Glass Frame

Lift the glass

frame up and

pull it forward to

remove.

Re-Attaching the Glass Frame:

a) Hang the glass frame on the firebox.

b) While holding in place, attach the upper latches

(follow the instructions to the right in reverse).

c) Lift the glass frame slightly and attach the lower latches.

NOTE:

You may need to lift the glass

frame while re-attaching.

Table of contents

Other Lopi Stove manuals

Popular Stove manuals by other brands

Dimplex

Dimplex Piermont PMN20 user manual

CASATELLI

CASATELLI ALEX 13 2C GENERAL INFORMATION - WARNINGS - INSTALLATION - MAINTENANCE

Eco-ideal

Eco-ideal eco 4 Installation and operating instructions

KAL-FIRE

KAL-FIRE Heat Pure 45 quick start guide

bemodern

bemodern 2661 Installation & user's instructions

AL Tech

AL Tech TORUS instructions

Ecosy+

Ecosy+ Snug 7 manual

HAMPTON BAY

HAMPTON BAY EST-540T-40R Use and care guide

Comfort Bilt

Comfort Bilt HP21-SS owner's manual

Haas+Sohn

Haas+Sohn HSP 6 Pallazza III 520.08 RLU-PGI Equipment sheet

Vanguard

Vanguard SCIVFBC Azure Blue Safety information

Austro Flamm

Austro Flamm GLASS manual

VALERII S & M GROUP

VALERII S & M GROUP K636 user manual

Alfa Plam

Alfa Plam COMMO COMPACT Installation, operation and maintenance manual

foc.us

foc.us Stofocus 2 Specific instructions

Austro Flamm

Austro Flamm Cody 2.0 operating manual

Austro Flamm

Austro Flamm BINGO manual

BOSSCO

BOSSCO Chefmax B-537 instruction manual

Lopi Sweet Dreams User manual

Popular Stove manuals by other brands