Lopolight 300-038 User manual

P/N 601-322 Rev 1.00
P/N 601-322 Rev 1.00 / 12 August 2020
Masthead lights: 300-036, 300-037, 300-038, 300-039, 300-136, 300-137, 300-138, 300-139
Installation guide
Installation guideInstallation guide
Installation guide
Thank you for purchasing a Lopolight product. Our products are built to ensure a long
lifetime in the most extreme marine conditions.
Mounting:
Mounting:Mounting:
Mounting:
Go to www.lopolight.com or use the R code
to get to the ‘products’ section where the
datasheet, that includes the dimensional
drawing, is found.
The alignment to vessel centerline is very important.
Horizontally mounted lights are opened/closed as illustrated.
Please ensure lock screw engages correctly.
Connecting power:
Connecting power:Connecting power:
Connecting power:
Supply Voltage: Any DC voltage between 20 and 32 volts (24 Volt systems).
C
CC
Cabled lights
abled lightsabled lights
abled lights:
::
: Red wire: Positive (+) Black
BlackBlack
Black wire: Negative ( - ).
(Double light: cables, same colour)
Light with green
Light with green Light with green
Light with green connector:
connector:connector:
connector:
Single light:
Pin 1: Positive (+) Pin 2: Negative ( - ) (pin 3-5: not used)
Double light:
Primary light: Pin 1: Positive (+) Pin 2: Negative ( - )
Secondary light: Pin 4: Positive (+) Pin 5: Negative ( - ) (pin 3
not used)
Recommended fuse or circuit breaker:
Recommended fuse or circuit breaker:Recommended fuse or circuit breaker:
Recommended fuse or circuit breaker: Less than 2A (slow).
Grounding:
Grounding:Grounding:
Grounding: The navigation light housing should not be connected to ground (Earth).
(We recommend that you connect the cable screen to ground (Earth)).
Cabl
CablCabl
Cabling
inging
ing:
: :
: Avoid chafe and route it away from sources of heat and large inductive
fields such as electric motors.

P/N 601-322 Rev 1.00
P/N 601-322 Rev 1.00 / 12 August 2020
Masthead lights: 300-036, 300-037, 300-038, 300-039, 300-136, 300-137, 300-138, 300-139
Cleaning your product:
Cleaning your product:Cleaning your product:
Cleaning your product:
•Wipe off your product with a normal detergent, on a damp cloth.
DO NOT use alcohol
DO NOT use alcoholDO NOT use alcohol
DO NOT use alcohol or thinner
or thinneror thinner
or thinner for cleaning your
for cleaning yourfor cleaning your
for cleaning your light
light light
light –
––
– this could
this could this could
this could
damage the lens.
damage the lens.damage the lens.
damage the lens.
Troubleshooting
TroubleshootingTroubleshooting
Troubleshooting:
::
:
If the light does not function:
•Check that you have a supply Voltage between 20 and 32 Volt DC.
•Check that the polarity is right (you will not damage the Lopolight by
accidentally wiring the polarity wrong).
End of life
End of life End of life
End of life signa
signasigna
signal
ll
ling
inging
ing:
::
:
Your Lopolight product has a microprocessor inside that ensures that the light has the
required intensity over a 50.000-hour projected lifetime. The light will signal to you when
it is getting to the end of its useful life. The following signals can be observed:
•All OK:
All OK: All OK:
All OK: 5 seconds after turning on the light it will go dark for 0,1 second and turn
on again. This is just a check for you to assure that the microprocessor is working.
•Less than 2000 working hours left:
Less than 2000 working hours left: Less than 2000 working hours left:
Less than 2000 working hours left: The dark period is extended to 2 seconds:
you should change the light at your next service within the next 12 months.
•Light Expi
Light ExpiLight Expi
Light Expired:
red: red:
red: The dark period is extended to 5 seconds: You should change
the light immediately. (The light will still be working, even in the expired state)
Warranty:
Warranty:Warranty:
Warranty:
•This product is covered by our 5-year limited warranty.
•If you want to claim a warranty for your product, please fill in the
form at www.lopolight.com/service
A
AA
Approval
pprovalpproval
pprovals
ss
s:
::
:
The light in this package is type approved to the following standards:
•EN-14744, UL-1104, COLREG72, IEC 60945
Recognized by the following authorities:
•IMO, MED (EU-wheelmark), USCG