Connecting the Cameras
Individual Power Adapter* Multi-Camera Power Adapter*
Connecting the Cameras
* Images for representation only
To install your camera:
1. Set the camera in the desired mounting position and mark
holes for screws through the camera base.
2. Drill the holes, then feed the cable through the mounting
surface or cable notch.
NOTE: Insert the included drywall anchors if you are
mounting the camera onto drywall.
3. Mount the camera stand to the mounting surface using
the provided screws. Make sure all screws are fastened
tightly.
4. Adjust the camera as shown below:
Installing the Camera
Extend the cable run for your camera depending on the cable type used.
Additional extension cables sold separately. See table below:
Connect the male power head
and the BNC connector to the
camera.
Connect the BNC connector
to a video input on your DVR.
Connecting the Camera
Cable Notch
LAB223_LAB243_QSG_EN_R3
Power Adapter Types
A multi-camera power adapter that provides power to multiple cameras
or individual power adapters may be provided, depending on product
configuration.
Problem Solution
No picture / signal • The cameras are only compatible with
certain Lorex HD DVRs. For the full list of
compatible recorders, visit
lorex.com/compatibility
• Ensure your TV or monitor is on the correct
input channel. Common terms for input
channels: INPUT, AV CHANNEL, LINE1,
LINE2, AUX.
• Ensure your DVR is properly connected to
your TV or monitor.
• Ensure connections are properly connected.
• Ensure the camera power supply is plugged
in.
Picture is too bright • Ensure your camera isn’t pointed directly at
a source of light (e.g., sun or spot light).
• Check the brightness settings of the DVR
and monitor.
• Move your camera to a different location.
Picture is too dark • Check the brightness and contrast settings
of the DVR and monitor.
Night vision is not
working
• The night vision activates when light levels
drop. The area may have too much light.
Picture is not clear • Check the camera lens for dirt, dust,
spiderwebs. Clean the lens with a soft,
clean cloth.
• Make sure that the cable run is within the
limitations specified in the section ‘Cable
Extension Options’.
Bright spot in video when
viewing camera at night
• Night vision reflects when pointing a
camera through a window. Move the camera
to a different location.
Troubleshooting
A. ROTATING THE ARM: Loosen the adjustment ring by turning it
counter-clockwise. Rotate the arm of the camera up to 360°, then
tighten the adjustment ring against the base.
B. BENDING THE ARM: Use a Phillips head screwdriver (not included)
to loosen the adjustment screw closest to the camera base. Bend the
arm of the camera up to 90°, then tighten the screw.
C. LEVELING THE CAMERA: Use the screwdriver to loosen the
adjustment screw furthest from the camera base. Rotate the camera
until it is level with the viewing area, then tighten the screw.
ATTENTION:
Test your camera prior to selecting a permanent mounting location by
temporarily connecting the camera and cable to your DVR.
Before Installing the Camera
• Decide whether to run the cables
through the wall / ceiling (drilling
required) or along the wall / ceiling.
• If you run the cables along the
wall / ceiling, you must run the
cable through the cable notch on the
base. This will keep the camera base
flush to the surface when mounted.
A B C
ATTENTION:
This camera includes an Auto Mechanical IR Cut Filter. When the camera
changes between Day/Night viewing modes, an audible clicking noise may
be heard from the camera. This clicking is normal, and indicates that the
camera filter is working.
Connect the female power
head to the included power
adapter.
Camera DVR
Male Power Female Power
Setup Diagram
BNC Video
12V DC Power
Camera
Extension Cable
Power Adapter
HD DVR
Cable Extension Options
Option Cable Type Max Cable Run
Distance
1Lorex model MCBL-60BNC4 BNC Cable
(included with camera) 60ft (18m)
2‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ Siamese
(Video and Power) 200ft (60m)
3‘RG59’ or ‘Coax’ or ‘Coaxial BNC’ (Video
Only)2500ft (150m)
Notes:
1. The extension cable must be a single stretch of cable between the
DVR and camera. You cannot connect multiple extension cables to
each other.
2. For cable runs above 200ft (60m), you must connect the power
adapter directly to the camera, rather than at the end of the
extension cable.
3. Baluns are not supported for LAB223.
4. Indicators that your cable run may be too long:
• Video is permanently black & white (even during day time)
• Video is unclear, soft, or distorted
5. For more information on extension cables, visit lorex.com
