LOUQE GHOST S1 MkII User manual

LOUQE AB
Designed in Sweden
[e-mail]
GHOST S1 MkII
LQ-GHS102-CA
USER MANUAL (ENG)

LOUQE AB
Designed in Sweden
[e-mail]

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
BOX CONTENT
4x M3x6 countersunk
8x M3x4 button head
4x M3x6 button head
4x #6-32 UNC
T10 torx key
Mounting platform
(for use with TopHat)
GHOST S1 MkII USER MANUAL

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Lift the grill away by pulling the rag tag in the
back
•Take out the screws bag and the mounting
platform

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Unscrew the 4 bottom screws that are holding
down the side panels x4

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Pull the side panels straight up and put them a
way

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Unscrew the PSU bracket x4

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Install the motherboard I/O shield

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Install the motherboard and screw it in place
•Push the Riser cable connector into the PCI-e
port on the motherboard
x4

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Connect the LED cables (white LED+, grey
LED-)
•Connect the power switch cables (brown and
black)
LED+
LED-
PWR SW
PWR SW
Black
Grey
White
Brown

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Screw the PSU to the PSU bracket
x4

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Connect the power cables needed to the PSU
and feed them to the approximate position
•Screw the PSU bracket back in place
•Connect the 24-pin power cable to the
motherboard and the CPU power (if needed)
x4

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Unscrew the GPU cover plate
•Remove the bottom flat nut x2

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Mount the GPU and fixate it by screwing the
bottom flat nut in place
•Slide in the GPU cover late in place and screw
it tight with the top flat nut
•Connect PCI-e power cables if needed
x2

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Slide down the side panels

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Fix the side panels to the case with screws
from the bottom x4

LOUQE AB
Designed in Sweden
[email protected]www.louqe.com
ILLUSTRATION
ASSEMBLY STEPS SCREWS
GHOST S1 MkII USER MANUAL
•Place the grill on top of the case

LOUQE AB
Designed in Sweden
[e-mail]
LOUQE AB
Designed in Sweden
[email protected]www.louqe.com