Love HM35 User manual
2SHUDWLQJLQVWUXFWLRQV
'LJLWDOKDQGKHOG
SUHVVXUHJDXJH
+0
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
2SHUDWLQJ,QVWUXFWLRQV
&RQWHQWV
2SHUDWLQJ(OHPHQWV
'HVFULSWLRQ
6DIHW\LQIRUPDWLRQ
2SHUDWLRQ
6ZLWFKLQJRQDQGRII
/LJKWLQJ
3QHXPDWLFFRQQHFWLRQ
)XQFWLRQVDQGRSHUDWLQJPRGHV
0HQXVHOHFWLRQDQGVHWXS
'DWDORJJLQJ
'DWDUHFRUGLQJ
7UDQVIHURIGDWDWRD3&
'HOHWLQJGDWD
&RPPXQLFDWLRQ
,5563URWRFRO
,5+DUGZDUHRIWKHLQVWUXPHQW
%DWWHU\UHSODFHPHQW
&DOLEUDWLRQ
6SHFLILFDWLRQV
7HFKQLFDOGDWD
0HDVXULQJ5DQJHDQG3UHFLVLRQ
0HDVXUHPHQWXQLWV
0DLQVVXSSO\XQLWFRQQHFWLRQ
0DLQWHQDQFHDQGVWRUDJH
:DUQLQJPHVVDJHVDQGIDXOWV
$FFHVVRULHV
6XPPDU\RIWHFKQLFDOFKDUDFWHULVWLFV
Oerating Elements
( ,�
s- +P
&
2
'HVFULSWLRQ
7KH+0GLJLWDOSUHVVXUHJDXJHLVDSUHVVXUHPHDVXULQJLQVWUXPHQWZLWKDQLQWHJUDWHG
SUHVVXUHVHQVRUIRUWKHPHDVXUHPHQWRIGLIIHUHQWLDOUHODWLYHRUDEVROXWHSUHVVXUHVDQG
YDFXXP,WVYHUVDWLOHUDQJHRIIXQFWLRQVDQGKLJKSUHFLVLRQUHQGHULWVXLWDEOHIRUDZLGH
UDQJHRIDSSOLFDWLRQV9LDWKHLQIUDUHGLQWHUIDFH,5DQG6&3,6WDQGDUG&RPPDQGVIRU
3URJUDPPDEOH ,QVWUXPHQWV FRPPDQGV WKH +0 FDQ FRPPXQLFDWH ZLWK D 3& ,WV
RSHUDWLRQLVYHU\VLPSOHDQGVXSSRUWVWKHXVHULQKLVPHDVXUHPHQWWDVNV
2SHUDWLQJPRGHV
• 3UHVVXUHPHDVXUHPHQW'LIIHUHQWLDOSUHVVXUH
• 0LQ0D[YDOXHV
• 0HDQYDOXHDYHUDJH
• 3UHVVXUHFKDQJHUDWH
• 'DWDORJJLQJ
6HOHFWDEOHFRQILJXUDWLRQSRVVLELOLWLHV
• 'DWDORJJLQJ
Æ,QWHUYDOWLPHSULQWWUDQVIHUGHOHWHGPHPRU\
• &RQILJXUDWLRQ
Æ0HDVXUHPHQWXQLWVGLVSOD\ILOWHUDXWRVZLWFKRIIWLPHDXWR]HUROLJKWLQJOHYHOHWF
• $YHUDJHSHULRGSHULRGIRUGHWHUPLQLQJDYHUDJHYDOXH
• 'DWHDQG7LPHUHDOWLPHFORFN
• &DOLEUDWLRQ
Æ'DWHRIODVWFDOLEUDWLRQGDWHPDQXDOUHFDOLEUDWLRQ
6DIHW\LQIRUPDWLRQ
•7KHSUHVVXUHYDOXHVDQGRYHUORDGOHYHOVVWDWHGRQWKHUDWLQJSODWHDQGTXRWHGLQ
WKHVHRSHUDWLQJLQVWUXFWLRQVPXVWQRWEHH[FHHGHGDVRWKHUZLVHWKHSUHVVXUH
VHQVRUFRXOGEHGHVWUR\HGRUWKHUHFRXOGEHDULVNRILQMXU\
• 2QO\XVHSUHVVXUHKRVHVZLWKDPD[LPXPORDGLQJFDSDFLW\FRUUHVSRQGLQJWRWKDW
QHFHVVDU\IRUWKHDSSOLFDWLRQ
• (QVXUHWKDWWKHSQHXPDWLFKRVHVDUHVHFXUHO\ILWWHG'RQRWXVHGDPDJHGRUNLQNHG
KRVHV
• 'RQRWRSHQXSWKHLQVWUXPHQWWKLVZRXOGYRLGWKHJXDUDQWHH
• 7KHLQVWUXPHQWPXVWEHVWRUHGZLWKLQWKHSHUPLVVLEOHVWRUDJHWHPSHUDWXUHUDQJH
7KHLQVWUXPHQWPXVWQRWEHSXWLQWRRSHUDWLRQLQDQ
H[SORVLYHHQYLURQPHQW
:HDUH\HSURWHFWLRQLIZRUNLQJZLWKSUHVVXUHV!EDU
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
✓
✓
✓
✓
✓
T
✓
✓
IT
IT I
IT I
Note
8
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
10
Notes
1) „Over“ (data type DISCRETE) for invalid pressure value
2) For the Data Type key, refer to the table on Page 18.
3) User-interval period will, for example, be displayed as follows, “user 01:15:00”
3.6.2 Transfer of data to a PC
(with HM35 Communication Software)
1. Install the IR (IrDA) -adapter according the instructions of the manufacturer.
2. Install the HM35 Communication Software.
3. Start the HM35 Communication Software.
4. Place the instrument max. 20 cm from the IR (IrDA)-Adapter and switch it on. Ensure
a line-of sight connection between instrument and IR-adapter!
If there is no communication with the instrument for more than 2 minutes, the IR
interface of the instrument turns off automatically! By restarting the instrument the IR
interface is reactivated.
3.6.3 Deleting data
1. In the Menu, select the Data Logging →Clear Memory function.
2. Press the Clear key.
3.7 Communication
3.7.1 IR/RS232-Protocol
COM-Port Settings
Baudrate 9600
Data bits 8
Parity no
Protocol no
Stop bit 1
Communication Protocol
Coding
The characters are transfered as ASCII-Code.
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
Initialisation Remarks
DTR
RTS
0
1
1
0
min. 50msec
ACT-220L/220L+ are programmed by toggling
the control lines RTS and DTR. These lines
may not be low at the same time during
operation. In this condition the ACT-
220L/220L+ goes in power down mode. If
DTR and RTS are low at the same time or in
an undefined condition, both lines must be set
high for at least 50 ms to leave the power
down mode.
Setting the baudrate
Remarks
RTS
DTR
min. 0.5usec
1
0
1
0
Before setting the baudrate the
ACT-220L/220L+ has to be initialised
according Initialisation. The baudrate is set
to 9600 bps according the opposite diagram.
A PC usually needs more than 0.5 us for an
I/O-Instruction.
Control commands
The control commands are largely defined by the Standard Commands for
Programmable Instruments (SCPI).
13
le�,
·-
16
Test Equipment Depot - 800.517.8431 - 99 Washington Street Melrose, MA 02176
TestEquipmentDepot.com
3.8 Battery replacement
•Open the battery compartment and insert 3 x 1,5 V Mignon cell AA, IEC LR6.
Always replace all three batteries at the same time!
Ensure correct polarity!
Dispose of used batteries in accordance with environmental
regulations!
3.9 Calibration
Re-calibration may only be carried out by specialist staff and with the corresponding
pressure standards.
We recommend that you have the HM35 re-calibrated at least once a year, and, in case
of highest demands for precision, several times a year.
Manual re-calibration
•In the Menu, select the Calibration →Manual Calibration function.
Zero point (Offset)
1. Open the pressure connection or, with the absolute pressure unit, set the given
pressure value to the normal pressure.
2. Press the Function key ( )
Îthe zero point will be re-calibrated.
Full-scale value
1. Set the given pressure value to the normal pressure.
2. Press the Function key ( )
Îthe full-scale value will be calibrated and the HM35 returns to normal operation.
19
Table of contents
Other Love Measuring Instrument manuals
