Lovencare ASTRO ROCKER BP 6612 User manual

INSTRUCTIONS FOR
ASTRO ROCKER
BP 6612
www.lovencare.com.au
[email protected]

WARNING
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
Failure to follow warnings and instructions could result in injury or death to your
child.
Make sure bouncer is fully assembled and secure before use.
•Never place a rocker on a table or other raised surface.
•Stop using the rocker when the baby begins to roll.
•Never leave a baby asleep unsupervised in a rocker.
•When handle not in use please store in rear pocket to prevent
Strangulation.
•Use a harness at all time
•Place the rocker clear of hazards such as heaters and kitchen stoves.
•Place the rocker clear of curtain and blind cords as they
are a strangulation hazard.
•Discontinue using rocker if it becomes bent, broken or if the cloth cover is
ripped or torn.
•ensure that the side adjustment latches are closed and secure before each use.
•NEVER use bouncer as a car seat as it will not protect your baby during an
accident.
•DO NOT lift bouncer by toy bar and canopy.
NOTE: This infant bouncer is designed only for use for children from birth to 20
lbs (9.0kgs), approximately 0-6 months.

Parts list
Toy Bar Frame
Care and maintenance
zClean frame with a damp cloth and a mild detergent and dry thoroughly.
zDo not use abrasive cleaners. Do not soak in water.
zThe toy bar cover may be sponged lightly using a damp cloth and mild
detergent.
zDry thoroughly before reuse. Do not fold or store the product while wet or in a
damp environment as this can cause mildew to form.
zAlways store your product in a clean dry place.
zDo not leave in the boot of car.
zAvoid exposure to salt water, as this may encourage the formation of rust. If
bouncer is used in this environment completely clean your bouncer afterward
to remove sand and salt from mechanisms.
zShould parts of your bouncer become stiff, squeak or difficult to operate
ensure dirt is not the cause.
zClean metal parts with a damp cloth and wipe dry.
zClean vinyl with mild soap and water solution.
zWhen storing bouncer, never stack other items on top of it, this may damage
the bouncer.
zPeriodically check for worn parts, loose screws, torn materials or stitching.
zReplace any damaged parts immediately

Assembly instructions
Step 1 – open frame
PUSH BOTH SIDE LATCHES DOWN TO LOOSEN THE STATE AND OPEN THE FRAME.
PUSH BOTH SIDE LATCHES UP TO SECURE THE FRAME, DRAW THE CANOPY.

Step 2 – install toy bar
TO INSERT THE EXPOSED ENDS OF TOY BAR INTO THE HOLES AT THE TOP OF
EACH OF THE PLASTIC SIDE MEMBERS.
EACH TOY IS ATTACHED BY A TAB TO THE TOY BAR COVER. PASS THE TAB
THROUGH THE LOOP OF EACH TOY TO SECURE IT TO THE BAR COVER.
Step 3 – using the carry handles
ALWAYS CHECK THAT ALL HOOKS ARE SECURELY CLASPED AND IN PLACE
BEFORE LIFT THE BOUNCER.
CAREFULLY AND SLOWLY PICK UP
THE BOUNCER USING BOTH
CARRY STRAPS.

Step 4 – using the safety harness
THIS BOUNCER IS FITTED WITH A 5 POINT SAFETY HARNESS.
YOUR CHILD MUST ALWAYS BE HARNESSED WHILE IN THE BOUNCER.
TO SLIDE COVER CLOTHS BEFORE ADJUST THE HARNESS STRAPS OR
RELEASE THE BUCKLE PRONGS.
RELEASE THE BUCKLE PRONGS – SQUEEZE ON THE TOP AND PULLAPART
FROM THE BUCKLE HOUSING.

Step 5 - TO ADJUST THE SEAT RECLINE Position
PUSH BOTH SIDE LATCHES DOWN FOR LOOSE STATE.
GRASP THE TOP OF SEAT AND ADJUST THE SEAT TO THE REQUIRED
POSITION. PUSH BOTH SIDE LATCHES UP TO SECURE THE BOUNCER.
Step 6 - SELECTING BETWEEN ROCKING MOVEMENT AND
STABILISED SEAT
TO ALLOW THE INFANT BOUNCER TO ROCK; SWING STABILISER PLASTICS
UP AND INWARD.
STABILISE THE SEAT BY SWINGING STABILISER PLASTICS OUT AND
DOWNWARD, SO THAT THEY REST ON THE GROUND.

Step 7 – to fold the rocker
REMOVE THE TOY BAR, PUSH BOTH SIDE LATCHES DOWN.
PUSH SEAT FORWARD.
PRESS THE SECOND LATCH ON THE BACK OF SIDE PLASTIC.
GOES ON, PUSH SEAT FORWARD UNTIL BOUNCER IS FLAT.

Contact Us:
Love N Care Pty Ltd.
297-299 Canterbury Rd, Revesby
NSW 2212 Australia
Contact No: 02 9774 4655
Fax: [phone]
Email: [email protected]
Website: www.lovencare.com.au