Lpg Mobilift m6 beauty User manual

In order to respond better to customer requirements and expectations, LPG Systems is continuously

researching ways of improving the design and quality of its products. This will explain the few minor

differences between your equipment and the item described in this guide.

≥ATTENTION

GU 1303-EN_ind B1

Edition dated 06/17

OPERATOR’S MANUAL

Mobilift M6®

Beauty

Registered trademark

Please read the complete manual carefully

before using your equipment

Reproduction, even in part, is strictly prohibited.

Congratulations on the purchase of your Mobilift M6

Beauty

. This model represents

the fruits of numerous years of experience in the design and production of

cutaneous tissue care systems. You will fully experience the technical perfection

and reliability of LPG Systems, which is the leader in this sector.

This operator’s manual contains the operating description, basic maintenance

instructions to be performed periodically and the safety instructions.

Your device is intended for use in the care of connective tissue. It should be used

only by a professional who has attended the manufacturer’s training provided by

LPG Systems or an approved provider, if you live outside France.

If you have any doubts whatsoever concerning the operation or maintenance of

your equipment, please do not hesitate to contact LPG via the Customer Service

Department of your distributor.

2 3

Unpacking instructions to be retained.

The manufacturer reserves the right to amend the product technical specifications without prior

notice. Any reproduction – even in part – is prohibited. All the illustrations in this operator’s manual

are non-binding.

≥ATTENTION

> PACKAGE CONTENTS > TABLE OF CONTENTS

> One Mobilift M6 Beauty unit

> One main Ergolift head

> Two Ergolift chambers (Lift 20 and Lift10)

> One electrical power cord

> One operator’s manual

> One POS marketing set

1. DESCRIPTION OF THE UNIT ....................4

2. DESCRIPTION OF THE CONTROLS .................6

3. PRECAUTIONS OF USE .......................7

4. MAINTENANCE ..........................11

5. ERGOLIFT HEAD ..........................16

6. TROUBLESHOOTING .......................20

7. TECHNICAL SPECIFICATIONS ..................21

8. WARRANTY ............................22

GENERAL WARRANTY CONDITIONS .......................22

WARRANTY ACTIVATION ..................................25

4 5

The unit can only operate if it is connected to the mains by its power cord and provided the ON switch

has been activated and the green voltage light is on.

After switching on the unit, please wait a few seconds for the screen to display information.

≥ATTENTION

DESCRIPTION OF THE UNIT

> MOBILIFT M6® BEAUTY > MOBILIFT M6® BEAUTY (CONT’D)

DESCRIPTION OF THE UNIT

HOSE

USB PORT

ACCESSORIES HOLDER

FORWARD-FACING TOUCH

SCREEN

TREATMENT CHAMBER

ERGOLIFT HEAD

HANDLE

AND ACCESSORIES

HOLDER CLIP

ACCESSORIES HOLDER

POWER CORD

ON/OFF SWITCH

FILTER BOX

6 7

11Europe VIIG-H05VVF3G0,75-C13; Italy I/3/16-H05VVF3G0,75-C13; Switzerland 12G-H05VVF3G0,75-C13; UK

BS13/13-H05VVF3G0,75-C13; Japan 498GJ-VCTF3X1,25-C13; USA, Canada, Mexico N5/15-SJT3X18AWG-C13

≥ATTENTION

> CONTROL SCREEN

> ERGOLIFT HEAD

DESCRIPTION OF THE CONTROLS

PRECAUTIONS OF USE

> WARNING

> IMPORTANT SAFETY INFORMATION

All safety precautions must be observed whilst using electrical equipment. Please read all

safety notices and precautions prior to use of the equipment.

DANGER - TO MINIMIZE THE RISK OF ELECTRICAL SHOCK:

• Always disconnect the equipment from the electrical supply outlet after use and before

cleaning and maintenance.

• Check that the supply voltage of the unit indicated on the data plate complies with

the mains voltage.

• The unit must be connected by the power cord1 supplied to a grounded outlet in accordance

with current electrical standards. Electrical adapters must not be used with this equipment.

• The equipment must not be left unattended

whilst connected to the electrical supply.

• Disconnect the unit from the electrical

supply if it is not going to be used for a long

period.

• Special attention is required whilst using

the equipment with, or in the proximity of

children or disabled persons.

• Never use the unit for purposes other than

those recommended by LPG Systems. Only

use the treatment heads supplied with your

unit or those recommended by LPG.

• Never use the equipment if:

- the electrical supply cable or outlet

is damaged.

- the equipment does not function correctly.

- the equipment is damaged or has fallen

or been dropped.

- the equipment has been exposed

to excessive humidity.

In such cases, return the equipment to an

approved LPG service centre.

• Do not move the unit by pulling on the

electrical supply cable.

• Fully unwind the electrical power cord and

keep it away from warm surfaces.

• Never use the equipment if the ventilation

ports are obstructed. Ensure that the

ventilation ports are kept clear of dust or

other contaminants.

• Do not allow solid debris, liquid or other

foreign bodies to fall or be sucked into the

unit, as these could cause damage.

• Never use the equipment on a dusty, uneven

floor, or in a moist atmosphere.

• Never use the equipment in the presence of

aerosols or oxygen.

• Before disconnecting the unit from the

electrical supply, set all controls to the ‘off’

position and unplug the unit.

• It is prohibited to modify this equipment

without prior authorisation from the

manufacturer.

• This device is a stationary device and shall

not be moved when in use.

-TO MINIMIZE THE RISK OF BURNS, FIRE, ELECTRICAL SHOCK OR INJURY

TOUCH SCREEN

TREATMENT

CONTROL SETTINGS

INFORMATION

ABOUT THE TREATMENT

TREATMENT CHAMBER

ERGOLIFT HEAD

FLAPS

8 9

ATTENTION: KEEP THESE INSTRUCTIONS

Your device should be used on clean, healthy skin. It is important to read and observe the

following precautions and contraindications before using your device.

• Never touch the client and the device’s

unprotected cables or connectors

simultaneously.

• Never use the auxiliary adapter as a

treatment head or allow it to come into

direct contact with the skin.

• Only use treatment heads supplied with your

unit or recommended by LPG.

• LPG Systems will not be liable for any

inappropriate use of the equipment.

• The operator must be particularly attentive

to the sensations felt by the person

undergoing treatment.

• The operator must ensure that the

parameters (intensity, sequentiality,

differential...) are always adapted to the

cutaneous tissue being cared.

• Do not use the USB and ethernet

connections during treatment.

• Do not operate the unit in unsuitable

environmental conditions (see technical

specifications).

• The MOBILIFT M6

Beauty

uses RF energy

only for its internal function. Therefore its

RF emissions are very low and not likely to

cause any interference to nearby electronic

equipment.

• The MOBILIFT M6

Beauty

is suitable for use

in all establishments including domestic and

those directly connected to the public low-

voltage power supply network that supplies

buildings used for domestic purposes.

• The MOBILIFT M6

Beauty

must be used on

a wooden, concrete or ceramic flooring. If

the floor covering is of synthetic material the

relative humidity must be at least 30%.

• The MOBILIFT M6

Beauty

must be connected

to an electrical supply equivalent in quality to

typical commercial or hospital supplies.

• If the operater of the MOBILIFT M6

Beauty

requires continuous function during power

supply network failure, it is recommended

that an alternative failsafe electrical supply

or battery power supply be provided.

• Portable or mobile RF communication

devices must not be used in close proximity

to the MOBILIFT M6

Beauty

or its cables.

• Interference may be encountered in

proximity to devices marked with the

following symbol:

> PRECAUTIONS OF USE

PRECAUTIONS OF USE

This unit contains programs to help the operator obtain the best anticipated results for each case undergoing

care. Under no circumstances may these programs be construed as a guarantee of successful care, which

varies, depending on the morphology, physiology and eating behaviour of each client.

≥ATTENTION

> CONTRAINDICATIONS

• Do not treat open wounds, the eyes,

intra-cavity areas, mucous membranes, the

genitals or breasts.

• Do not treat a client with an infectious

disease, a growing tumour, a phlebitis, a

wound, or an infected area.

• Do not treat a client with skin cancer, a

visible tumor, or other cancerous lesions.

Consult with a doctor in cases where the

client has a case history of tumours or is in

remission.

• Do not treat people with circulatory problems

without first consulting their doctor.

• Do not treat any swollen or inflamed

areas without seeking medical advice and

without having had training in specific LPG

techniques in this particular area.

• Do not treat client after basic medical care

without medical advice and LPG technical

training for the affected areas.

• Stop treatment immediately if the client

experiences pain and consult a doctor.

• This device should not be used on skin

rashes, herpes, inflamed or infected acne, or

vitiligo.

• To avoid bruising, exercise caution when

determining a client’s level of sensitivity and

avoid use on clients taking anti-coagulant

drugs.

• For a more detailed list of the indications

and contra-indications of ENDERMOLOGIE,

please refer to the training manuals.

• As this list is not exhaustive, always seek

medical advice in the event of doubt.

• Because of the risk of interference, it is

important that the professional ensures

the client is not equipped with a personal

medical device such as a pacemaker.

If this is the case, the professional should

obtain details about the device in question to

ensure that any interference will not affect

the correct use of the equipment.

> ELECTROMAGNETIC COMPATIBILTY

10 11

Do not use corrosive products such as acetone, trichloroethylene, or rubbing alcohol.

≥ATTENTION

MAINTENANCE

4 > IDENTIFICATION RATING PLATE

MAINTENANCE

> CLEANING THE UNIT

Your unit is identified by a serial number

shown on the rating plate.

The rating plate also shows the permitted

supply voltage for the unit.

If you need to contact LPG Systems because

of a technical problem, please indicate the

serial number of your MOBILIFT M6 Beauty.

This serial number provides information

on the year and month of manufacture

of your unit.

The letter indicates the year the device was manufactured. Z=2009, A=2010, B=2011, etc. The two

digits indicate the production month: 01=January; 02=February; 03=March; etc.

serial

number

voltage, frequency

and power

It is recommended that you clean your unit as often as possible, not only for reasons

of hygiene and aesthetics but also because cleaning the unit will help keep it in a good

working order and extend its useful life.

Using a moist sponge, clean the following sections:

• All the external hoods.

• Hoses.

• The electrical supply cable.

Using a cloth soaked with a small amount of alcohol-free domestic cleaning product,

clean the following sections:

• Control screen and control panel.

This icon indicates that the unit was

sold after August 13, 2006. In conformity

with the 2002/96/CE directive, it cannot

be thrown away with standard

household waste but must be disposed

of by means of recycling. When your

device reaches the end of its useful life,

it must be brought to an appropriate

recycling center or returned to your

dealer. By doing so, you help the

environment by contributing to the

conservation of natural resources and

the protection of human health.

This icon indicates that some specific

warnings or precautions associated with

this device are not on the label.

This symbol means always consult the

accompanying documents before using

your device.

This symbol means store the device

somewhere protected from inclement

weather.

This symbol indicates temperature

limits.

This symbol indicates relative humidity

limits.

This symbol means

« Danger: High Voltage » (US only)

Identiﬁcation rating plates may vary. The approved one is one on your machine.

≥ATTENTION

1312

FIG. 2FIG. 1

FIG. 3 FIG. 4 FIG. 5

> INSTRUCTIONS FOR CONNECTING THE HOSE

• To connect the hose, proceed as indicated below:

• Position the locking ring in the locked position (fig. 1).

• Position the end of the hose so that the hose key is lined-up with the key slot of the treatment

head connection (fig. 2).

• Push the hose into the treatment head connection until it clicks into place.

FIG. 1 UNLOCKED LOCKED

FIG. 6 FIG. 7

FIG. 2

HOSE RETAINER KEY

LOCKING RING ORNAMENTAL RING

MAINTENANCE

4 > REPLACING THE FILTER CARTRIDGE

Your device contains a filter cartridge.

These components guarantee the efficiency of your unit and prolong its useful life.

Ensure that they are changed as soon as the command screen displays one of these

messages (fig 1-2) :

Access the ‘filter change’ menu as follows :

Select the ‘maintenance’ menu by pressing the icon indicated (fig. 3).

Select the ‘filter’ menu by pressing the icon indicated (fig. 4).

The ‘ﬁlter change’ screen indicates which ﬁlter requires to be changed (ﬁg. 5).

ICON INDICATING A FILTER

CHANGE IS REQUIRED (FIG. 2).

WARNING MESSAGE

Never use your device without a filter.

Turn the device off before replacing your filter cartridge.

≥ATTENTION

> REPLACING THE FILTER CARTRIDGE (CONT’D)

MAINTENANCE

Replace the filter cartridge with a new one. (fig. 6)

Once the filter cartridge is replaced, the filter meter should be reset by pressing the icon as

indicated : (ﬁg. 7).

1514

≥

MAINTENANCE

FIG. 3 FIG. 4

> TRANSPORTATION/MOVING

• Remove the accessories holder (fig. 1).

• Carry the device by the handle (fig. 2).

FIG. 2

> INSTRUCTIONS FOR DISCONNECTING THE HOSE

• To disconnect the hose, follow the same steps in the reverse order: Unlock by turning the locking

ring (fig. 3). Lift the locking ring, then remove the hose gently by pulling on the white ring (fig. 4).

MAINTENANCE

• Replacing flaps: once the flaps no longer treat the skin properly, they must be replaced. They

should be replaced after every 20 hours.

• A personal Endermolift Kit for use by the client is available for sale.

> REPLACING THE POWER CORD

> MAINTENANCE LOG SHEET

If the power cord of your device is damaged, please contact LPG Systems Customer Service

for a replacement.

LPG Systems Customer Service:

+33 (0)4 75 78 69 89

WHITE RING

FIG. 1

When transporting your Mobilift M6 Beauty, you should:

Never carry the device by the accessories holder.

ATTENTION

DATE NO. OF HOURS OPERATIONS PERFORMED

1716

CONNECTION

ERGOLIFT HEAD

5 > ERGOLIFT HEAD DESCRIPTION

ERGOLIFT HEAD

> ERGOLIFT CHAMBER

Only the Lift 20 and Lift 10 chambers can be connected to the Ergolift head.

They can be connected and disconnected by a simple push-pull action.

Lift 20

chamber

with removable

Lift 20 flaps

Lift 10

chamber

with removable

Lift 10 flaps

HOSE

HOSE CONNECTION

ERGOLIFT CHAMBER

TREATMENT CHAMBERS

CONNECTION

1918

ERGOLIFT HEAD

5 > CLEANING THE ERGOLIFT HEAD

AND ERGOLIFT CHAMBERS

FIG. 1 REMOVAL TOOLS

FIG. 2

90° ROTATION

For reasons of hygiene, the treatment heads should be cleaned after each use, using

antiseptic wipes impregnated with a bactericidal and fungicidal solution.

Special attention must be given to the cleanliness of the parts that are in contact with the

client.

Before each use, clean the flaps and Ergolift chamber:

1. Disconnect the chamber from the Ergolift treatment head. (fig. 1)

2. Remove the flaps thanks to the dedicated tool. (fig.2)

3. Thoroughly clean the Ergolift chamber, the flaps and the tool for at least one minute

with the wipes described here below. (fig.3)

4. Put the flaps back in the Ergolift chamber by following the same steps in the reverse

order (fig.4)

ERGOLIFT HEAD

> CLEANING THE ERGOLIFT HEAD

AND ERGOLIFT CHAMBERS (CONT’D)

FIG. 3

90° ROTATION

FIG. 4

The use of aggressive products, such as acetone, trichloroethylene, or alcohol, and abrasive sponges, ultrasound

or UV lamps is strictly prohibited. All cleaned and/or disinfected heads should be placed in the storage drawer to avoid

any confusion.

≥ATTENTION

2120

> WHAT IF I’VE PROBLEM?

TROUBLE SHOOTING

TECHNICAL SPECIFICATIONS

> TECHNICAL SPECIFICATIONS

Dimensions; length x width x height: ...................................65 x 26 x31 cm

Net weight: ..............................................................10,5 kg

Maximum set depression: .........................................35 kPa (350 mbar)

Cooling: ..........................by mechanical ventilation incorporated into the pump

Protection index: ............................................................ IP20

Electrical protection class: ......................................................1

Operating temperature: ............................................. +10°C to +30°C

Storage temperature: ............................................... -20°C to +70°C

Electrical features: .......................................100-240V / 50-60Hz / 80 VA

Operating environment:

Ambient temperature: ............................... 10 to 30° C for normal operation.

Ambient relative humidity: ............................ 30 to 75% without condensation.

Atmospheric pressure: ..........................no significant influence for operation.

Max altitude: ............................................................ 2,500 m

Unit fitted with patented treatment heads.

Device designed for uninterrupted use.

The Mobilift M6 Beauty is labeled in accordance with legislation and standards set

forth in directives EMC 2004/108/EC and low voltage 2006/95/EC.

• Is the unit properly connected to a mains plug?

• Is the mains plug live?

• Is the ON switch lit up?

• Are the filter cartridges clean and correctly placed?

• Is the hose properly connected?

•Is the hose clogged?

• Are the care chamber and flaps properly connected?

Once these checks have been carried out and if the malfunction persists, please contact

LPG Systems Customer Service or the nearest authorized dealer, indicating the model of

your unit and its serial number.

If your unit is not working properly, proceed with the following checks before calling

Customer Service:

LPG Systems Customer Service:

+33 (0)4 75 78 69 89

2322

WARRANTY

8 > GENERAL WARRANTY CONDITIONS

You have recently acquired an appliance

distributed by LPG Systems or an LPG

Systems approved distributor. It is the

purchaser/user’s responsibility to find out

from the local authorities the conditions and

professional qualifications that should be met

before using the appliance.

The purchase of this equipment implies

the legal acceptance by the purchaser/

professional user of these general warranty

conditions. If the appliance was sold to you

by an approved LPG Systems distributor, the

purchaser/user should refer to the supplier’s

warranty conditions. These may in no way

increase the undertakings made in these

present warranty conditions. The warranty

can only be implemented and is only valid if

the warranty slip has been duly filled out and

returned to LPG Systems within two weeks of

delivery, irrespective of the country. Warranty

slips that are only partially completed will be

rejected.

The appliance is guaranteed against

manufacturing flaws and defects in the raw

materials. The warranty extends for the

shorter of the following two periods: one (1)

year OR two thousand (2000) hours of use

from the invoice date. During this period, LPG

Systems undertakes to exchange or repair

free of charge, as quickly as possible, any part

that LPG Systems acknowledges as defective,

however LPG Systems does not undertake

to replace the entire appliance. Travelling

and living expenses for our technicians and

transportation costs of the appliance or parts

to and from the after-sales service workshop

are not covered by this warranty.

Replacements and repairs performed within

this warranty, with or without immobilization

of the equipment, shall not have the effect of

extending the warranty period. Replaced parts

become the property of LPG Systems or the

approved distributor. No compensation shall

be paid for loss of use. The purchaser/user is

required to allow LPG Systems the necessary

time and means to carry out all repairs and

deliveries of replacement spare parts. Failure

to comply will absolve us from our obligations

under the warranty.

The only courts of competent jurisdiction are

those within the legal district of LPG Systems’

head office regardless of any jurisdiction

clauses in any other document.

WARRANTY

> GENERAL WARRANTY CONDITIONS (CONT’D)

Warranty exclusions:

• Damage occurring during transportation.

Transportation of this equipment and/or

spare parts is at the recipient’s own risk.

Before taking delivery, it is the recipient’s

responsibility to verify the state of the goods

and to make a claim against the transport

company in the manner usual in the delivery

country.

• Non-observance of the installation and

operating instructions, failure to carry

out maintenance and/or negligence in

maintaining the appliance and/or its filter

cartridges, connection to a faulty electric

supply or a non-earthed electric supply or

a power supply whose voltage is different to

the one indicated on the appliance.

• If an appliance is sold before the end of the

warranty period, the warranty is transferred

to the purchaser for the remaining warranty

period, on the condition that:

i) the original invoice is provided.

ii) that the initial vendor is informed of

the sale.

• Modification, mounting of accessories or

dismantling of the equipment.

• Any operation and/or intervention not

specified in the LPG Systems Operating

Instructions and performed on the

equipment by the purchaser/user and/or any

party not approved by LPG Systems.

• Use of consumables, spare parts,

inappropriate components or parts not

supplied by LPG Systems.

• Blockage of the appliance through aspiration

of a foreign body.

• Normal wear and tear of any of the

equipment’s parts.

• Falls, impacts, lightning, fire, force majeure,

water damage and natural disasters.

2524

WARRANTY

> LIMITATION AND EXONERATION OF LIABILITY

Non-compliance with the general guarantee conditions during the term of the warranty and

following expiry of the latter, may lead to LPG Systems being exonerated of any liability in

the event of damage attributed to the products supplied.

LPG Systems will not be held liable in respect of equipment/material losses or physical

accidents (i), following installation that does not comply with the statutory or regulatory

provisions of the country where the unit is to be used or (ii) which could jeopardize a

MOBILIFT M6

Beauty

unit, which was the subject of intervention work not scheduled in

the LPG Systems operator’s manual and/or carried out by the operator or a third party not

authorized by LPG Systems.

LPG Systems will be absolved of its liability in the event of use exceeding the level of

professional competence/qualification of the operator or resulting from the incorrect use of

the unit.

The personal data collected in this form are sent to LPG Systems, which is responsible for processing it in order to manage customers relations, including

after-sales service and warranties. Information with an asterisk must be provided in order for this form to be processed. According to modified French law

78-17 from January 6, 1978 relating to computers, digital files, and freedoms, also known as the “Informatique et Libertés” law, you have a right of access,

rectify, and remove personal data about you by contacting LPG Systems in writing at the following address: LPG SYSTEMS – 30, rue Dr Abel – Technoparc

de la Plaine - CS 90035 - 26902 VALENCE (FRANCE).

> WARRANTY ACTIVATION

> OR FILL IN THE FORM AND RETURN

TO LPG SYSTEMS

You can activate your warranty online by connecting to our

warranty webpage:

http://warranty.lpgsystems.com

Name*: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Address*: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Country*: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Tel*: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Email: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Type of business: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Profession: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Type of unit: MOBILIFT M6 Beauty

Serial number*: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Date: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

≥ATTENTION

To validate the warranty, detach this slip and return to the address below within 15 days following delivery of the unit:

LPG SYSTEMS SA - 30, rue du Dr Abel

Technoparc de la Plaine - CS 90035 - 26902 VALENCE Cedex 9 – France