LS Industrial Systems XGT Series User manual

XDesignerPlus Ver2.0 Communication device
1 / 41
LS Industrial Systems Co., Ltd
XGT(XGK-CPU), XGB(XBC-CPU/XBM-CPU) Series
CNET Driver
Support version
OS
V4.0 and over
XDesignerPlus
4.0.0.0 and over
CONTENTS
Thank you for using TOP series of M2I corporation.
Please read this manual carefully to know connection methods and
procedures of “TOP to External device”.
1. System configuration
Page 2
A section for showing connectable external devices, serial signal
types, connection configurations. Refer this section to select the
right system configuration.
2. Selection of TOP, External device
Page4
A section for selecting a Top model and the external device.
3. Example of system setting
Page 5
A section for explaining examples to connect communications of
TOP to External Device.
Select the correct example in your case according to “1. System
configuration”
4. Communication setting
Page 27
A section for Communication setting.
The setting should be the same with the external device.
5. Cable diagram
Page 30
A section for cable to connect to external device.
Select a suitable cable diagram for your system.
6. Usable address
Page 35
A section for usable address to communicate with external
device.

XDesignerPlus Ver2.0 Communication device
2 / 41
Series
CPU*1)
Link I/F
Comm. type
System setting
Cable
XGK
XGK-CPUH
XGK-CPUA
XGK-CPUS
XGK-CPUE
XGK-CPUU
XGL-C22A, CH1
RS232
4.1 setting ex 1
( 5 Page )
5.1 cable diagram 1
( 30 Page )
XGL-C22A, CH2
RS232
4.2 setting ex 2
( 7 Page )
5.1 cable diagram 1
( 30 Page )
XGL-C42A, CH1
RS422
4.3 setting ex 3
( 9 Page )
5.2 cable diagram 2
( 31 Page )
RS485
4.4 setting ex 4
( 11 Page )
5.3 cable diagram 3
( 32 Page )
XGL-C42A, CH2
RS422
4.5 setting ex 5
( 13 Page )
5.2 cable diagram 2
( 31 Page )
RS485
4.6 setting ex 6
( 15 Page )
5.3 cable diagram 3
( 32 Page )
XGL-CH2A, CH1
RS232
4.1 setting ex 1
( 5 Page )
5.1 cable diagram 1
( 30 Page )
XGL-CH2A, CH2
RS422
4.5 setting ex 5
( 13 Page )
5.2 cable diagram 2
( 31 Page )
RS485
4.6 setting ex 6
( 15 Page )
5.3 cable diagram 3
( 32 Page )
XGB
XBM-D□16S
XBM-D□32S
XBC-D□32H
XBC-D□64H
CPU on Cnet*2), CH1
RS232
4.7 setting ex 7
( 17 Page )
5.4 cable diagram 4
( 33 Page )
CPU on Cnet*2), CH2
RS485
4.8 setting ex 8
( 19 Page )
5.5 cable diagram 5
( 34 Page )
XBL-C21A, CH2
RS232
4.9 setting ex 9
( 21 Page )
5.1 cable diagram 1
( 30 Page )
XBL-C41A, CH2
RS422
4.10 setting ex 10
( 23 Page )
5.2 cable diagram 2
( 31 Page )
RS485
4.11 setting ex 11
( 25 Page )
5.3 cable diagram 3
( 32 Page )
Type name
Image
Detail name
Cnet
on CPU unit
5 pin terminal port of XBC/XBM/XEC CPU module ( RS-232 1 port + RS-485 1 port )
1. System configuration
System configuration of TOP and “LS Industrial Systems Co., Ltd – XGT(XGK), XGB(XBC/XBM) Series”.
*1) Confirm that version written CPU unit label is 1.1 and over.
*2) Cnet port on CPU unit of XGB Series

XDesignerPlus Ver2.0 Communication device
3 / 41
■ Connection configuration
ㆍ1 : 1(TOP 1 unit to External device 1 unit) connection – It is available with RS232C/422/485.
ㆍ1 : N(TOP 1 unit to External device N unit) connection – It is available with RS422/485.

XDesignerPlus Ver2.0 Communication device
4 / 41
Setting Items
Description
TOP
Series
Series
OS Version
XTOP / HTOP
V4.0
Select a TOP series which is communicated with external device.
Install an OS file v3.1 as diagram below before download a project file you have made.
Name
Select a TOP model which is communicated with external device.
External Device
Vendor
Select vendor of the external device which is communicated with TOP.
Select “LS Industrial Systems Co., Ltd”.
PLC
Select a model name of the external device which is communicated with TOP.
Select “XGT(XGK), XGB(XBC/XBM) Series CNET”.
Check whether the external device you want to use is connectable or not
in “1. System configuration”.
2. Selection of TOP, External device
Select a external device which is communicated to the TOP.

XDesignerPlus Ver2.0 Communication device
5 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-232 (COM2)
RS-232 (CH 1)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3. Example of system setting
Set Communication interface of TOP and " XGT(XGK-CPU),XGB(XBC-CPU/XBM-CPU)Series CNET Driver".
3.1 Example 1
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
6 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Parameter Write].
7. Reset PLC at [Online] > [Reset] > ][Reset PLC].
Item
Contents
Note
Connection
setting
CH 1
Comm. Type
RS232C
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
Fixed
Station No.
0
User set
RunMode
CH 1
XGT server
fixed

XDesignerPlus Ver2.0 Communication device
7 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-232 (COM2)
RS-232 (CH 2)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3.2 Example 2
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
8 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. Double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Write].
7. Reset PLC at [Online] > [Reset PLC].
Item
Contents
Note
Connection
setting
CH 2
Comm. Type
RS232C
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
fixation
Station No.
0
User set
RunMode
CH 2
XGT server
fixation

XDesignerPlus Ver2.0 Communication device
9 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-422 (4 wire, COM2)
RS-422 (4wire, CH 1)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3.3 Example 3
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
10 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. Double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Write].
7. Reset PLC at [Online] > [Reset PLC].
Item
Contents
Note
Connection
setting
CH 1
Comm. Type
RS-422
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
fixation
Station No.
0
User set
RunMode
CH 1
XGT server
fixation

XDesignerPlus Ver2.0 Communication device
11 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-485 (2 wire, COM2)
RS-485 (2 wire, CH 1)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”.
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3.4 Example 4
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
12 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. Double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Write].
7. Reset PLC at [Online] > [Reset PLC].
Item
Contents
Note
Connection
setting
CH 1
Comm. Type
RS-485
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
fixation
Station No.
0
User set
RunMode
CH 1
XGT server
fixation

XDesignerPlus Ver2.0 Communication device
13 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-422 (4 wire, COM2)
RS-422 (4wire, CH 2)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”.
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3.5 Example 5
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
14 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. Double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Write].
7. Reset PLC at [Online] > [Reset PLC].
Item
Contents
Note
Connection
setting
CH 2
Comm. Type
RS-422
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
fixation
Station No.
0
User set
RunMode
CH 2
XGT server
fixation

XDesignerPlus Ver2.0 Communication device
15 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-485 (2 wire, COM2)
RS-485 (2 wire, CH 2)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”.
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3.6 Example 6
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
16 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. Double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Write].
7. Reset PLC at [Online] > [Reset PLC].
Item
Contents
Note
Connection
setting
CH 2
Comm. Type
RS-485
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
fixation
Station No.
0
User set
RunMode
CH 2
XGT server
fixation

XDesignerPlus Ver2.0 Communication device
17 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-232 (COM2)
RS-232 (CH 1)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”.
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3.7 Example 7
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
18 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. Double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Write].
7. Reset PLC at [Online] > [Reset PLC].
Item
Contents
Note
Connection
setting
CH 1
Comm. Type
RS-232C
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
fixation
Station No.
0
User set
RunMode
CH 1
XGT server
fixation

XDesignerPlus Ver2.0 Communication device
19 / 41
Item
TOP
External device
Note
Serial Signal Level (port/channel)
RS-485 (2 wire, COM2)
RS-485 (2 wire, CH 2)
User set
Station number (PLC Address)
─
0
User set
Serial Baud rate
[BPS]
115200
User set
Serial Data bit
[Bit]
8
User set
Serial Stop bit
[Bit]
1
User set
Serial Parity bit
[Bit]
NONE
User set
Run Mode
XGT private server
User set
■ [ Project >Project Property > Project >TOP Setting > TOP Name ]
Set communication interface of TOP.
■ External device setup
Set the communication driver option “XGT(XGK), XGB(XBC,XBM) Series CNET”.
-Station Number : Station number of external device.
-CPU Type : Select CPU type
-Device Read Type : Select protocol type.
3.8 Example 8
Set your system as below.
(1) XDesignerPlus Setting
[Project >Project property] of XDesignerPlus as below and download it to TOP machine.

XDesignerPlus Ver2.0 Communication device
20 / 41
(2) External device setup
Run "XG-PD Editor" program for communication setting and set as below.
If you want to change communication interface, modify refer to PLC manual.
1. Run File > New File”. Select CPU Type and push OK button refer to “1. system configuration”.
2. Connect CPU LOADER port of XGT Series and serial port of PC by serial cross cable.
(If there is USB port in CPU, connect USB.)
3. Run [Online] > [Connection settings] menu. Select [Connection settings->Type] and click [Connect] button.
4. Run [Online] > [I/O Information] and read slot number. Run [Online] > [Read Parameter] and read parameter information of slot
of communication card.
5. Double click slot of Cnet card in [Project Window], show dialog box of [Default settings].
Set [Connection] and [Run Mode] as below and click [OK].
6. Transfer setting contents to CPU at [Online] > [Write].
7. Reset PLC at [Online] > [Reset PLC].
Item
Contents
Note
Connection
setting
CH 2
Comm. Type
RS-485
fixation
Baud rate
115200
User set
Data bit
8
User set
Stop bit
1
User set
Parity bit
NONE
User set
Modem Type
Null
fixation
Station No.
0
User set
RunMode
CH 2
XGT server
fixation