LST FSK700-2SX User manual

© LABOR STRAUSS SICHERUNGSANLAGENBAU GMBH • A-1231 WIEN • WIEGELESTRASSE 36 • TEL [phone] • FAX [phone]
[email protected] • WWW.LST.AT • ALL RIGHTS RESERVED
FSK-ZBH_DBL_LST_EN_0820.PDF • PAGE 1
ABuilding Safety. Building Security.
Flush Mounting Frame EZ700-2
The Flush Mounting Frame EZ700-2 is used for
the easy fl ush mounting of the Fire Brigade Key
Boxes FSK700-2 and FSK700-2SX.
When the building is structurally complete, the
fl ush mounting frame is embedded in a wall and
then the facade is completed.
Afterwards, the fi re brigade key box can be
inserted into the fl ush mounting frame and it can
be screwed on fi rmly by means of the two bolts.
Later on, disassembly is possible in the same
way.
Dimensions W × H × D 275 × 245 × 160 (mm)
Weight 3.3kg
Order number 265751
Order name Flush Mounting Frame EZ700-2
Specifi cations
Fire Brigade Key Box
Accessories
• Frames for fl ush mounting or for
installation into stainless steel
columns
• Various inner doors and accessories
for different locks
• Protective cover for installation on
outside facades
• Power supply for heating of the
outer door

© LABOR STRAUSS SICHERUNGSANLAGENBAU GMBH • A-1231 WIEN • WIEGELESTRASSE 36 • TEL [phone] • FAX [phone]
[email protected] • WWW.LST.AT • ALL RIGHTS RESERVED
FSK-ZBH_DBL_LST_EN_0820.PDF • PAGE 2
ABuilding Safety. Building Security.
Protective Cover WSD-FSK
The Protective Cover WSD-FSK is made of stain-
less steel and provides the Fire Brigade Key Box
FSK700-2 or FSK700-2SX with additional pro-
tection against moisture in the area of the outer
door, when rainwater hits this area from above
or at the side.
The protective cover is placed behind the blind
frame of the fi re brigade key box from above.
Dimensions W × H × D 287 × 267 × 55 (mm)
Weight 500g
Order number 249650
Order name Protective Cover for FSK700-2/2SX WSD-FSK
Specifi cations
Flush Mounting Frame with Drilling Protection EZBS700-2
The Flush Mounting Frame EZBS700-2 serves
for the installation of the Fire Brigade Key Boxes
FSK700-2 and FSK700-2SX. The integrated all-
round drilling protection allows for installation
according to the Guideline VdS 2350 in the fol-
lowing ways:
• Flush mounting: When the building is structu-
rally complete, the fl ush mounting frame is
embedded in a wall, and after completion of
the facade the fi re brigade key box is screwed
on the frame.
• Installation into a hollow stainless steel column
without concrete fi lling
• Mounting on buildings in light-weight construc-
tion, on heat-insulating facades or on any
walls that are not strong enough to provide
suffi cient protection against sabotage.
Dimensions W × H × D 275 × 245 × 160 (mm)
Weight 3.5kg
Approval VdS G106058
Order number 265818
Order name Flush Mounting Frame with Drilling Protection EZBS700-2
Specifi cations

© LABOR STRAUSS SICHERUNGSANLAGENBAU GMBH • A-1231 WIEN • WIEGELESTRASSE 36 • TEL [phone] • FAX [phone]
[email protected] • WWW.LST.AT • ALL RIGHTS RESERVED
FSK-ZBH_DBL_LST_EN_0820.PDF • PAGE 3
ABuilding Safety. Building Security.
Inner doors and accessories
Inner door for profi le half cylinder 30.5mm
Dimensions W × H × D 108 × 150 × 5 (mm)
Weight 500g
Order number 265752
Order name Inner Door for Profi le Half Cylinder 30.5mm ITA-2
Inner door for profi le half cylinder 35.5mm
Dimensions W × H × D 108 × 150 × 5 (mm)
Weight 500g
Order number 265748
Order name Inner Door for Profi le Half Cylinder 35.5mm ITA-3
Inner door for double-bit lock type 2/2005
Dimensions W × H × D 108 × 150 × 5 (mm)
Weight 400g
Order number 265753
Order name Inner Door for Double-bit Lock Type 2/2005 ITB-2
Inner door for double-bit lock type 70091/92
Dimensions W × H × D 108 × 150 × 5 (mm)
Weight 400g
Order number 265757
Order name Inner Door for Double-bit Lock Type 70091/92 ITF-2
Specifi cations
Depending on which lock has been determined
by the responsible fi re brigade, different inner
doors are available, which allow to accommodate
the respective locks.
The Inner Doors ITA-2 and ITA-3 are equipped
with a lock for the use of a 7-pin profi le half
cylinder.
The Inner Door ITB-2 can accommodate the
double-bit locks type 2 and type 2005.
The Inner Door ITF-2 can hold the double-bit lock
type 70091/92.
The Auxiliary Cylinder PHZ700-2 can be installed
into the fi re brigade key box instead of the profi le
half cylinder for the building key. In this case, one
or more building keys are attached by means of
a chain link.
By means of the Mounting Bracket for Profi le Half Cylin-
der PHZAW700-2, a Fire Brigade Key Box FSK700-2SX
can be easily upgraded from a two-key model to a
version for three or four building keys.

© LABOR STRAUSS SICHERUNGSANLAGENBAU GMBH • A-1231 WIEN • WIEGELESTRASSE 36 • TEL [phone] • FAX [phone]
[email protected] • WWW.LST.AT • ALL RIGHTS RESERVED
FSK-ZBH_DBL_LST_EN_0820.PDF • PAGE 4
ABuilding Safety. Building Security.
Operating voltage 230VAC +10/-15%, 50Hz
Output voltage 24VAC
Protection class IP30
Ambient temperature 0°C to +70°C
Dimensions W × H × D 110 × 180 × 80 (mm)
Colour grey white
Weight 900g
Order number 237700
Order name Power Supply for FSK Heating NT700-1
Specifi cations
Power supply for heating NT700-1
Auxiliary cylinder
Order number 265744
Order name Auxiliary Cylinder for FSK700-2/2SX PHZ700-2
Mounting bracket for profi le half cylinder
Order number 265743
Order name Mounting Bracket for Profi le Half Cylinder PHZAW700-2
The standard equipment of the Fire Brigade Key
Boxes FSK700-2 and FSK700-2SX includes a
heating device, which consists of several SMD
heating resistors that are placed on the drilling
protection board. The heating device prevents
the outer door from freezing in extreme weather
conditions, and at the same time it keeps the
interior of the safe dry.
The heating device of the fi re brigade key box
can be easily powered by the Power Supply
NT700-1.
A built-in miniature circuit breaker protects the
line side of the device.
The power supply is accommodated in a surface-
mount housing which is also suitable for moun-
ting on a DIN rail.