Lucius FLEX R User manual

USER MANUAL

2 3
USER MANUAL
INTRODUCTION
1. PRODUCT DESCRIPTION
2. CONTENTS
Congratulations for purchasing your LUCIUS FLEX .
Please read and understand this manual in its entirety before using the LUCIUS
FLEX . Have a certified personnel to install this fixture. Only use this product as
specified within the manual.
A
B
D
I
C
E
GH
K
J
GLance Hanger (x2)I
J K FLEX Manual L
L
ALED Fixture BLED Driver C
DInput Power Cable 2.4m
EF
Output Cable
Driver Mount (x2) Output Extension Cable 2m
3.5mm Signal Cable 2m HRope Rachet (x2)
S-Hanger (x2) M4 Eyebolt (x2)
F
The LUCIUS FLEX provides growers with the latest OSRAM LED technology in a
robust design.
The series technology adopts enhanced red diodes to achieve a PPF efficacy up
to 3.50umol/J (400W & 680W) and 3.65umol/J (1000W).
Each bar is built to last with an innovative IP65 rated silicon that protects the LEDs
without compromising light output. Delivering optimal growth, crop after crop.

3
3. TECHNICAL SPECIFICATIONS
LUCIUS FLEX
Product Code M2142 M2143 M2146
Power 400W 680W 1000W
Voltage Range/
Frequency
120-277V
50/60Hz
100-277V
50/60Hz
200-277V
50/60Hz
Current
120V 3.50A 5.84A -
208V 1.98A 3.37A 4.91A
220V 1.86A 3.18A 4.63A
230V 1.78A 3.05A 4.43A
240V 1.71A 2.92A 4.25A
277V 1.50A 2.53A 3.72A
PPF Efficacy 3.5umol/J 3.65umol/J
Max PPF 1400umol/s 2380umol/s 3650umol/s
CCT 4000K
CRI 60%
PF >0.95
THD <10%
Beam Angle 120°
Control Knob OFF / 25% / 50% / 75% / 100% / RC
External Control Compatible with 0-10V LED Controllers
Signal Cable 3.5mm TRS Male Jumper Cable
Thermal
Management Passive
BTU/h 1365 2320 3413
Protection Over-voltage , Under-voltage, Short Circuit, Over-temperature
Dimensions 1170 x 690 x 62mm
46.06 x 27.16 x 2.44”
1170 x 1115 x 79mm
46.06 x 43.90 x 3.11"
1170 x 1115 x 79mm
46.06 x 43.90 x 3.11”
Weight 4.74±0.3kg
10.38±0.66lbs
8.5±0.5kg
18.7±1.1lbs
10.4±0.3kg
22.9±0.66lbs
Working Temp 0°C to 40°C / 32°F to +104°F (95% RH)
Storage Temp -40°C to 70°C / -40°F to +158°F (85% RH)
IP Rating IP65
Warranty 3 Years
Certificates

4 5
4. DIMENSIONS
79mm
680W (6 BAR)& 1000W (10 BAR)
1115mm
1170mm
See lucius.com.au to view the PPFD Map.
2
Coverage Area refers to the region that the plants receive at minimum 200PPFD for Flowering and 100PPFD for Vegetative.
1
Hanging Height refers to the distance between the plant canopy and the LED.
2
62mm
400W (4 BAR)
690mm
1170mm
LIGHT COVERAGE AREA
Fixture
400W 680W 1000W
Application
Veg Flower Veg Flower Veg Flower
Hanging
Height (cm)
73 38 28 96 50 38 126 76 65
Max PPFD
(umol/s/m
2
)
500 1000 1200 500 1000 1200 500 1000 1200
Coverage
Dimensions (m)
1.9 x1.7 1.4 x 1.1 1.4 x1.1 2.2 x 2.3 1.6 x 1.7 1.5 x1.7 2.9 x 2.9 2.0 x 2.1 1.9 x 2.0
Coverage
Area (m
2
)
3.23 1.62 1.48 5.17 2.76 2.50 8.52 4.10 3.90
1
2

5
5. INSTALLATION
NOTE: DO NOT remove safety covers protecting the LEDs until fixture is installed.
Push mounts onto driver.
Lock driver mounts onto LED bars.
Ensure mounts are flush to driver base.
Attach lance hangers to fixture hanging
tabs. Use two people to lift into position.
Unbox and unfold the LUCIUS FLEX on a flat surface with the LEDs facing down.
DRIVER-FIXTURE INSTALLATION
STEP 1. ATTACH DRIVER MOUNTS
STEP 2. ATTACH DRIVER AND HANG FIXTURE
REMOVE the LED safety covers before powering on fixture.

6 7
1. Slide and tighten eyebolts
in driver channel.
2. Secure S-Hanger to anchor
point and hang driver.
REMOTE DRIVER INSTALLATION
OPTION 1. SURFACE MOUNT
OPTION 2. S-HANGER
Mount driver to a secure
surface with screws.
Attach lance hangers to fixture
hanging tabs. Use two people to
lift into position.
Connect the output extension
cable between the fixture and
driver.
REMOVE the LED safety covers
before powering on fixture.

7
6. CONTROL
(1) Manual Control
(2) External Control
The dimming knob has 5 power levels. 25%, 50%, 75%, 100% and OFF.
Connecting Single LED Fixture
Connect your external LED controller to the driver by connecting the 3.5mm Signal
Cable to the “IN” Port. Then set the dimming knob to the RC setting.
Connecting Multiple LED Fixtures
Continuing on from ‘Connecting Single LED Fixture’ instructions. Connect 3.5mm
Signal Cable to the “OUT” port of the first driver and connect to the “IN” port of
the second driver. Repeat these steps until your desired numbers of fixtures are
connected.
RC
Input port
Output port
RC
Controller
Driver 1
Signal Cable
Driver 2 Driver 80
7. WARRANTY -CONTACT YOUR RETAILER FOR WARRANTY
CLAIMS AND SUPPORT.
The company guarantees the mechanical and electronic components of this
product. It ensures the materials and workmanship is free of defects, used under
normal operating conditions. If there are any defects with this product that relate
to the workmanship or the materials used, the company shall, at its discretion,
either replace or repair the product.
However, improper use is NOT covered by warranty. This includes but is not limited
to, overloading, user error, physical or water damage. Warranty is valid for a period
of three years from the original date of purchase.

8
CERTIFIED BY
CERTIFIED BY
CERTIFIED BY
lucius.com.au