LUCKY DOG Easy Ship CL 61598 User manual

BOX KENNELS
C
L 41098
5' wide x 10' long
x 4' high
C
L 40598
5' wide x 5' long x 4' high
C
L 61098
5' wide x 10' long
x 6' high
C
L 61598
10' wide x 10' long
x 6' high
or
5' wide x 15' long
x 6' high
*Includes Weatherguard Kennel Cover
CL 64410*
4' wide x 4' long x 6' high
CL 61099* ~ 5' wide x 10' long x 7' high

STEP #1
PARTS LIST
Separate and compare all Parts A through K. If you
purchased the Yard Guard or Hi-Rise Dog Kennel set
aside Parts L-O for use in construction of your kennel
cover.
IMPORTANT NOTICE!
PLEASE READ INSTRUCTIONS COMPLETELY PRIOR TO
ASSEMBLING YOUR LUCKY DOG EASY SHIP
™
CHAMPION DOG KENNEL.
Watch for helpful assembly “
Hints!
” when following these instructions.
A
C D E F G H K
I J
B
Parts A-
K
Parts A-E quantities are the same for all
kennels
A
24" Swing Gate with Stand 1
A 24" Swing Gate with Stand 1A
B
Lockable Fork Latch 1
C
Corner Stand NO Rod Clips 3
D
Corner Stand WITH Rod Clips 1
E
Upper & Lower End Rails 4
Hi-Rise 5' 10' 15'
Parts F-K quantities are different for most
kennel lengths
F
Center Stand 0 0 2 4
G
Upper & Lower Side Rails 4 4 8 12
H
Round Tension Rods 2 2 2 2
I
Steel Wire Ties 20 30 45 60
J
Stand Caps 1 4 6 8
K
Chainlink Roll 1 1 1 1
K Chainlink Roll 1 1 1 1K
Quantity per kennel length
Quantity per kennel length
TOOLS REQUIRED
#2 Phillips screwdriver and Pliers
#2 Phillips screwdriver and Pliers
#2 Phillips screwdriver and Pliers
STEP #2
SITE CHOICE AND GROUND PREPARATION
Choosing your kennel location is very important
to the well being and safety of your pet-companion. The
site should be flat and clear of foreign objects and should be
protected from sun and other weather elements that may be
harmful to your pet.
Receiver Tube
Receiver Tube

STEP #3
FRAMEWORK ASSEMBLY
You will note that the pre-assembled gate is pre-hung
on the gate stand (Part A) and is constructed to allow
the upper and lower end rails (Part E) to slide through
receiver tubes at the top and bottom of the gate stand.
To accomplish this, simply loosen the set screws on the
receiver tubes and lay the gate frame with chainlink
mesh side down flat on the ground. Slide the end rails
through the receiver tubes.
DO NOT TIGHTEN SET
SCREWS AT THIS POINT.
Hint!
All Lucky Dog
Kennels feature a
1
" extension
on the bottom side of each stand. This allows the
kennel to sit above the ground surface for easy
cleaning and air flow
to lessen the potential for
bacterial buildup. Make
sure all extensions are on the
bottom.
STEP #4
Attach corner stand with rod clips (Part D) to latch
end of upper and lower end rails just installed and
tighten set screws of corner stand. (Figure 1)
Hint!
Use caution not to over tighten set screws to
avoid damaging the welds.
STEP #5
Attach corner stand with no rod clips (Part C) to
opposite end of end rails and tighten set screws.
The CL61598 Kennel can be assembled in a
5' wide x
15' long or a 10' wide x 10' long size.
If the 5' wide
x 15' long design is choosen use two center stands
(Part F) on two sides of you kennel. If the
10' wide x
10' long design is chosen use one center stand (Part F)
on each side.
Fig. 2
Fig. 3
Fig. 4
Fig. 1
Receiver
Tubes

STEP #6
Now you are ready to install the bottom two side
rails (Part G) into the bottom receiver tubes of the
corner stands just installed and tighten set
screws.
At this point, carefully stand the entire gate
side of
kennel upright and install the top two side rails into
the top receiver tubes and tighten set screws.
STEP #7
If you have purchased a 5' long kennel, you will
now
install the remaining two corner stands
(Part C) and
remaining two upper and lower end
rails (Part F).
If you have purchased a 10' or 15'
long kennel,
you must continue to install the side
rails using
the
center stands (Part F) until you have
completed
the
full length of your kennel. Now
install your remaining
two corner stands and two
remaining upper and lower end rails as first outlined
in this section.
Hint!
There is one side section on a 5' long kennel,
two side sections on a 10' long kennels and three
side sections on a 15' long kennel.
STEP #8
GALVANIZED CHAINLINK
MESH INSTALLATION
For ease of shipping the
compact roll of
chainlink mesh is
folded versus rolled.
The recommended
handling of this mesh
is to unfold it onto a
flat surface checking
along the top and bottom for pickets that may have
come unhooked from each other or that need to
be twisted back into place. After checking, roll the
chainlink back up in the manor you would roll up
a carpet. This will insure ease of handling when
proceeding with the final installation steps.
Stand roll of chainlink next to the corner stand with
rod clips (Part E) and insert a round tension rod
(Part H) into end of mesh and hook the rod into the
rod clips as shown in Figure 2.
Hint!
Attach chainlink mesh to upper side rail
using a steel tie wire (Part J) to insure the mesh stays
at proper height.
STEP #9
Unroll chainlink mesh around the outside of the
kennel frame. Pulling mesh tight at each center
and/or corner stand, use a steel wire tie (Part I) to
secure the top and bottom of the mesh to the top
and bottom rail so the mesh will not slide back and
become loose.
STEP #10
Once you have completely unrolled the chainlink
mesh around the entire kennel frame, you will install
the final round tension rod into the rod clips on the
hinge side of the gate.
Hint!
The chainlink mesh is pre-cut to easily fit
the kennel size however the exact mesh length is not
always possible. Therefore, one or more chainlink
pickets may need to be removed to insure proper
tension on the mesh.
If pickets need to be
removed, straighten out as
many pickets as necessary
at top and bottom and
twist out the
picket until
proper length is achieved
(Figure 3).
STEP #11
Install the lockable fork latch (Part B) on the
latch side of the gate. Tighten bolts until latch is
firmly attached to gate frame. Pull the gate frame
toward the corner stand until the proper distance
between corner stand and gate frame is achieved
(approximately 2" gap). Make sure latch opens and
closes
easily. Tighten the final set of screws on the
gate stand (Part A).
STEP #12
Using the remaining
steel tie wires (Part I),
begin tying the mesh
securely to all top and
bottom rails (Figure 4).
Make sure the tail end
of the tie wire is always
pointing outside the frame
to insure your pet does
not come in contact with it. The bottom tie wires
should be approximately 12" apart and top rail
ties approximately 18" apart. If any additional tie
wires are left, you can use them at the corner and/or
center stands.
S
TEP #13
If you have purchased the
Yard Guard or Hi-Rise
Kennels or
a Weatherguard
™
Kennel Cover, please
™ Kennel Cover, please ™
skip Step 13 and begin assembly of you kennel cover.
Insert stand caps (Part J) into top opening of corner,
center stands and gate frame.
Fig. 2
Fig. 3
Fig. 3
Fig. 4
Fig. 4

Fig.
3
Fig.
2
Fig.
1
S
TEP #1
Insert A-frame gable supports (Part L) into
top of corner stands (Part C and Part D) and
center stands (Part G). Slide ends of tubing
down as far as possible.
S
TEP #2
Install the two-way end clamps (Part M) at
the center of each A-frame gable support
(Part L) that rests on corner stands
(Figure 1)
.
If installing on a 10' or 15' long kennel,
install
three-way center clamp (Part N) at the
center of
A-frame gable supports that rests
on center stands (Figure 2).
Center
ridge pole
(Part O) between A-frame gable supports and
tighten
(Figure 3).
S
TEP #3
Unfold kennel cover material and drape over
kennel cover frame. Secure with elastic tie
downs (Part P - not shown).
Hint!
Avoid over stretching the tie downs as
it could cause damage to grommets.
Parts
L-O
Hi-Rise 5'x5' 10'x5' 15'x5' 10'x10'
L
A-Frame Gable Supports 2 2 3 4 3
L A-Frame Gable Supports 2 2 3 4 3L
M
Two-Way End Clamps 2 2 2 2 2
N
Three-Way Center Clamps 0 0 1 2 1
O
Center Ridge Poles 1 1 2 3 2
P
Elastic Tie Downs (
not show
n)
8
8 12
14 14
OPTIONAL: WEATHERGUARD™ KENNEL COVER AND FRAME
INSTALLATION INSTRUCTIONS
To purchase a Weatherguard™ Kennel Cover for your Lucky Dog™ Kennel contact customer service at 1.800.955.2879
L
M
N
O

EXTREMELY IMPORTANT!
Pet-companions are very comfortable in this safety enclosure, however, it is
suggested that there be a brief
introduction period to acclimate your pet-
companion.
To begin this process, place your pet in the kennel
for short periods of time (10-20
minutes) throughout
the day while you are able to observe their behavior.
If your
pet begins to show signs of discomfort or nervousness (e.g., barking or whining)
administer verbal correction from a distance. As the training continues, gradually
increase the duration of stays
inside the kennel until the pet has become completely
comfortable with their new surroundings. Providing play things for your pet-
companion will also comfort them. Also, insure that clean and adequate water and
food is available at all times.
REMEMBER,
verbal and physical affection will aid your pet-companion to be
completely satisfied with their new safety enclosure.
LIMITED EXPRESS WARRANTY
Jewett-Cameron Companies warranties your Lucky Dog Box Kennel to be
free of defects in workmanship and further warrants that under normal use will
be free of problems for one full year from date of purchase
by original purchaser.
JEWETT-CAMERON COMPANIES WILL NOT HAVE OTHER OR
GREATER LIABILITY FOR DEFECTS NOR WILL JEWETT-CAMERON
COMPANIES HAVE ANY LIABILITY FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.
If you discover a defect in the kennel during the warranty period and wish to obtain
replacement parts or have questions send notice of claim to:
Jewett-Cameron Companies
PO Box 1010 • 32275 NW Hillcrest
North Plains, Oregon 97133
Include your return address and a copy of the original invoice or further
proof of the date of purchase plus a description of the claimed defect.
All implied warranties of merchantability and fitness for particular
purpose are limited in duration to one (1) year from date of purchase. Some
states do not allow limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which may vary from state to state.
1-800-955-2879 E-mail: [e-mail]