LuckyBot Ender-3 User manual

Welcome to LuckyBot

Please read this manual carefully before using the
product and keep it properly.
Content
Legal Disclaimer Notices
Prohibitions
Usage Advice
Product Introduction
Operation
Product Parameters
Unpacking List
Usage Guide
Compatible FDM 3D Printers
Chocolate Temperature Adjustment Parameters Table
Chocolate Slicing Parameters Table
Other Ingredients Printing Parameters Table
Care and Maintenance
Chocolate Printing Troubleshooting
Performance Fault Table
Warranty Card
Warranty Policy
Non-warranty Regulations
...........................................................................01
..................................................................................................01
...............................................................................................02
..................................................................................03
.....................................................................................................04
...................................................................................04
...........................................................................................05
...............................................................................................07
....................................................................07
....................07
.....................................................08
......................................08
...............................................................................08
......................................................09
...........................................................................09
.............................................................................................09
...........................................................................................10
........................................................................10

Legal Disclaimer Notices
Prohibitions
1. All images of the product are taken in kind. The actual product and photos
will vary due to photographic techniques, light, monitor parameters, and other
factors. Please prevail in kind.
2. This manual is limited to introducing LuckyBot’s actual compatible FDM
3D printers.
3. Independent entities manage LuckyBot and the brands corresponding to
the compatible models in this manual.
4. LuckyBot does not have any commercial relationship with the brands men-
tioned in the manual.
5. All users, managers, inspectors, and maintenance personnel must be
familiar with and follow the standard procedures of this manual. And pay
special attention to the cautions and national laws, industry regulations, and
legal safety precautions to avoid causing accidents and damage to the prod-
uct.
6. Maintenance personnel should maintain the product by the methods
described in this manual. Parts that are frequently touched and used must be
kept safe and intact during the maintenance and must stay unbroken.
7. The user must repair and replace parts within Wiiboox’s authorization.
8. Persons with physical, sensory, or mental disabilities or persons lacking
experience and knowledge (including children) must be supervised by a
guardian and instructed when using the product. The guardian must be able
to take responsibility for the user’s safety. Otherwise, it may lead to injury or
other accidents.
9. This manual may not be an exhaustive list of all safety warning information.
Please confirm that the method will neither endanger personal safety nor
damage the equipment when choosing any operation.
10. Wiiboox as the production side to ensure product quality. Due to the
user’s reasons for improper operation resulting in product damage, Wiiboox
does not bear legal responsibility and economic losses.
01
1. Do not disassemble the product without cutting off the power.
2. Do not disassemble the product when the printhead and hot bed of the
original FDM 3D printer are at high temperatures. (Be sure to keep the print-
head and hot bed in a cool state when disassembling.)
3. Do not use any ingredients with added granules for printing, such as nuts,
dried fruit, crushed cookies, etc.
4. Do not use the product in a humid, high-temperature environment.
5. Do not use any accessories, wires, etc. that are not provided by Wiiboox.
6. Do not drop the product or subject the product to strong impact, as this
may result in electric shock or fire due to a short circuit. In case of abnormal

Usage Advice
-ity or malfunction, such as overheating, smoking, peculiar smell, abnormal
sound, abnormal temperature display, etc., please stop using and cut off the
power immediately, and contact with after-sale personnel as soon as possi-
ble.
7. Do not bend, pull or block the lead screw forcibly. Otherwise, the product
will not work normally.
8. Do not repair, disassemble or modify the product yourself at random.
Otherwise, it may cause injury due to a short circuit, fire, or abnormal opera-
tion. Please contact after-sales personnel when repairs are required.
9. Do not damage, modify, forcefully bend, pull, twist, place heavy objects on
top of the power cord or squeeze the power cord, as it may cause electric
shock or fire due to a short circuit.
10. Do not long press the up and down buttons to cause motor blocking so
as not to damage the internal motor of the product.
1. Please use metal nozzle for printing chocolate and plastic nozzle for print-
ing other ingredients.
2. Please install the tube in place by screwing it tightly to ensure that the tube
and the base are fully seated.
3. Please ensure sufficient contact between the plunger and the piston of the
tube when printing.
4. This product has high requirements for ingredients. Please use the choco-
late recommended in this manual to print, and follow the video provided on
the official website to fill, refrigerate, preheat, print, etc.
5. Please load the “For LuckyBot.gcode" configuration file before printing
each time and refer to luckybot.us/file.php for detailed instructions.
6. This product has high requirements for model design. Please download the
model from the official website for printing before mastering the use.
7. This product requires a low ambient temperature (≤18°C) as the pure fat
chocolate solidifies slowly when printing. Users can use air conditioners to
reduce the ambient temperature or place ice bags around the model to cool
during the printing.
02

Product Introduction
1
Lead Screw
Display Panel
Side Door
Enclosure
Plunger
Button
LuckyBot is a food 3D printer extruder developed for FDM 3D printers.
Make your 3D printing fun, loving and tasty! LuckyBot! Be more for you!
03

Operation
Product Parameters
Product Dimensions
Weight of Product
Nozzle Type
Tube
Printing Speed
Power Supply Mode
Rated Voltage
Rated Power
Control Mode
Temp. Control Range
Temp. Control Accuracy
Refresh Rate
Connectivity
72*72*260mm
675g
18# Metal nozzle,16G Plastic nozzle
LuckyBot customized tube
Set by 3D printer itself system
DC12V
36W
Manual / Control
≤40℃
±0.5°C
4times/sec
LuckyBot Line-10P integrated wire
Lead screw up
Temp.++
Lead screw down
Temp.--
Power on / off
Switch Temp.
04
Extruder power supply
3D printer power supply
Long press:
Short press:
*The Sidewall Temp. is displayed as long light, while the Bottom
Temp. is displayed as flashing. Please observe when switching.

Unpacking List
31
2
2
10
15
16
4
5
3
1
4 5
6
7
8
9
17 P1 R1
14
11 12
13
18 19
05
* Please refer to the List of Z-axis Extension Plate (WL-wheel) for details.
* Please refer to the List of LuckyBot Standard Package for details.

List of LuckyBot Standard Package
List of Z-axis Extension Plate (WL-wheel)
No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Name
LuckyBot
Tube
Line-10P integrated wire
Metal adapter plate
Metal nozzle
Plastic nozzle
E-axis adapter wire
Limit extension wire
Limit extension wire
Socket cap screws
Socket cap screws
Socket cap screws
T-nuts
M5 flat washers
L-type inner hexagon wrench
L-type inner hexagon wrench
TRM (Temperature resistance module)
AC/DC adapter
Dual-port wire
Spec
/
60ML
1M
/
18#
16G
/
ForANY
ForCRA
M3*8
M4*10
M4*8
M4
M5*10*1
2MM
3MM
T680
12V3A
C13/C14
Qty
1
1
1
1
2
2
1
1
1
4
3
3
3
3
1
1
1
1
1
06
No
1
2
3
4
5
Name
Z-axis extension plate (WL-wheel)
L-type inner hexagon wrench
Socket cap screws
Open end wrench
Open end wrench
Spec
L160
4MM
M3*6
8MM
10MM
Qty
1
1
3
1
1
* Z-axis extension plate (WL-wheel) is optional.

Compatible FDM 3D Printers
Chocolate Temperature Adjustment
Parameters Table
Usage Guide
Ender-3/3S/3Pro/3V2/3MAX、Ender-5
Pro/Plus、Ender-6、Ender-7、
CR-10/10V2/10V3
Mega X/Mega Zero/Mega Zero 2.0
Aquila/Aquila C2
Mizar、A10 Pro/A10 M/A10T、
A20/A20M/A20T、A30 Pro/A30M/A30T
Hornet
Cre**ty
Any**bic
Fla**Forge
Ge**tech
Art**ry
* More compatible models continue to update...
* The above parameters are for reference only. Please check the official website for details.
* The reference data provided in the Preheating temperature and Printing temperature columns, the
former being the Sidewall Temp. and the latter being the Bottom Temp. Printing temperature may
vary depending on the ambient temperature. Please pre-extrude after reaching sufficient preheating
time. If the chocolate is too thin, adjust the temperature downwards. If the chocolate is difficult to
flow out, adjust the temperature upwards.
Brands Models
07
Please scan the QR code or enter the URL for filling chocolate, installation
guide, instructions for TRM (temperature resistance module), instructions
for Z-axis extension plate (WL-wheel), printing operation, etc.
user.luckybot.us
PROMISES DARK CHOCOLATE
CALLEBAUT-70-30-38 70.5%
CALLEBAUT-811 54.5%
SPECIAL DARK MILDLY SWEET
CHOCOLATE
MILK CHOCOLATE
INTENSE DARK 60% CACAO
INTENSE DARK 72% CACAO
INTENSE DARK 86% CACAO
MILK CHOCOLATE SQUARES
30min
30min
30min
30min
30min
30min
30min
30min
30min
36℃ 36℃
35℃ 35℃
35℃ 35℃
35℃ 35℃
35℃ 35℃
35℃ 35℃
35℃ 35℃
35℃ 35℃
36℃ 36℃
32℃ 32℃
34℃ 34℃
34℃ 34℃
34℃ 34℃
34℃ 34℃
33℃ 34℃
33℃ 34℃
32℃ 32℃
37℃ 38℃
GHIRARDELLI
HERSHEY'S
CALLEBAUT
DOVE
Preheating
time
Preheating Printing
Chocolate
brand Chocolate model Sidewall
Temp.
Bottom
Temp.
Sidewall
Temp.
Bottom
Temp.

Care and Maintenance
Warning: Please be sure to disconnect the power before cleaning and
maintaining LuckyBot.
1. Please use LuckyBot customized tube to prolong the product’s service
life.
2. Please use a dry cloth and cotton swab to clean the inside and outside of
the base after using LuckyBot to prevent the residual material from mildew-
ing and gathering.
3. Please remove the nozzle and unclog it after using LuckyBot to ensure
that the chocolate can be extruded normally in the subsequent use.
4. Please move the lead screw down inside LuckyBot before installation or
disassembly to prevent damage to the accuracy of the lead screw.
* The above parameters are for reference only. Please check the official website for details.
*For other ingredients of semi-fluid food such as blueberry jam, peanut butter, mashed potatoes,
etc., the print slicing parameters are roughly set as in the table above.
Chocolate Slicing Parameters Table
Other Ingredients Printing Parameters Table
Model Slicing
Layer
Thickness
Bottom / Top thickness
Filling density
Diameter
Nozzle aperture
Frame
0.5mm
1.68mm
0.5mm
0
21/22mm
0.84mm
0.5mm
1.68mm
0.5mm
50%
21mm
0.84mm
0.5mm
1.68mm
0.5mm
50%
21mm
0.84mm
Ingredients
Layer
Thickness
Bottom / Top thickness
Height of model
Filling density
Diameter
Extrusion volume
Nozzle aperture
Printing temperature
Salad
0.6 mm
1.68mm
0.6 mm
1.2mm
0
20mm
130
0.84mm
Same as ambient
temperature
Ketchup
0.7mm
1.68mm
0.6 mm
1.4mm
0
20mm
130
0.84mm
Same as ambient
temperature
08
Solid
(fat replacement model)
Solid
(pure fat model)

Chocolate Printing Troubleshooting
Performance Fault Table
Performance Faults
LuckyBot
1. Powered on but cannot be turned on.
2. Function button failure
3. Powered on but no heating.
4. Powered on but the lead screw cannot work.
Name
Warranty Card
User Contact Information
Product Information
Purchase Date
Product Model
Name
Telephone Number
Address
Fault phenomenon
No ingredients flow out
The side door cannot be
closed during printing
Unshaped print
Possible causes Solutions
Incorrect preheating
The air inside the tube
Ingredients contain granules
Nozzle clogged
E-steps value not set to 750
mm/s
The tube and the inside of the
LuckyBot are stained with water
Low bottom temperature
There is a residual ingredient
on the inside of the base
Excessive printing temperature
Preheat at constant temperature for
20-30 minutes. Please put the tube
back in the refrigerator for about 30
minutes and repeat the preheat
operations if over-preheat.
Invert the tube and shake to expel air.
Please use ingredients without any
added granules for printing.
Unclog the nozzle or replace it with a
new one.
Adjust the E-steps value to 750 mm/s.
Ensure all parts of LuckyBot are dry.
Increase the Bottom Temp. by 1°C.
Clean up the residue with a fine
needle or cotton swab.
Adjust the temperature of the
sidewall or bottom.
09
*Please refer to the table above for some common troubleshooting when printing other ingredients.

1. Please keep the warranty card properly as proof of repair.
2. The warranty period is 12 months from the date of purchase.
3. Wiiboox will provide free repair and replacement for quality problems
or failures during the warranty period and under regular use and main-
tenance after verification.
4. The company reserves the right to modify and interpret all contents.
1. The product is damaged due to incorrect installation and operation.
2. Repairs, alterations, modifications, and replacement of any product
components by non-wiiboox technicians.
3. The product label number is altered to be inconsistent with that listed
in this certificate.
4. Damage caused by negligent use or infiltration of water or other
substances into the product.
5. Accidents are caused by natural disasters or damage.
Due to the differences between different machines, the physical objects
and the final images can differ. The final explanation rights shall be
reserved by Yancheng Wiiboox 3D Technology Co., Ltd.
Notes:
Manual version: V2.1
After-sales mailbox: [email protected]
Website: www.luckybot.us
Manufacturer: Yancheng Wiiboox 3D Technology Co., Ltd.
Address: 2F, Building 9, Zone A, Big Data Industrial Park, Yandu District,
Yancheng City, Jiangsu Province, China.
Warranty Policy
Non-warranty regulations
10