Ludlum Measurements 700e Series User manual

LUDLUM MODEL
700e Series
INTEGRATED SPECTROSCOPY
with EXTERNAL DETECTOR
May 2019
Serial Number ID001000 and Succeeding
Serial Numbers

LUDLUM MODEL
700e Series
INTEGRATED SPECTROSCOPY
with EXTERNAL DETECTOR
May 2019
Serial Number ID001000 and Succeeding
Serial Numbers

STATEMENT OF WARRANTY
Ludlum Measurements, Inc. warrants the products covered in this manual to be free
of defects due to workmanship, material, and design for a period of twelve months
from the date of delivery. The calibration of a product is warranted to be within its
specified accuracy limits at the time of shipment. In the event of instrument failure,
notify Ludlum Measurements to determine if repair, recalibration, or replacement is
required.
This warranty excludes the replacement of photomultiplier tubes, G-M and
proportional tubes, and scintillation crystals which are broken due to excessive
physical abuse or used for purposes other than intended.
There are no warranties, express or implied, including without limitation any implied
warranty of merchantability or fitness, which extend beyond the description of the
face there of. If the product does not perform as warranted herein, purchaser’s sole
remedy shall be repair or replacement, at the option of Ludlum Measurements. In no
event will Ludlum Measurements be liable for damages, lost revenue, lost wages, or
any other incidental or consequential damages, arising from the purchase, use, or
inability to use product.
RETURN OF GOODS TO MANUFACTURER
If equipment needs to be returned to Ludlum Measurements, Inc. for repair or calibration, please
send to the address below. All shipments should include documentation containing return shipping
address, customer name, telephone number, description of service requested, and all other necessary
information. Your cooperation will expedite the return of your equipment.
LUDLUM MEASUREMENTS, INC.
ATTN: REPAIR DEPARTMENT
501 OAK STREET
SWEETWATER, TX 79556
800-622-0828 325-235-5494
FAX [phone]

Model 702e

Table of Contents
Introduction 1
About Your Model 700e Series Unit 1-1
Caution Statement 1-1
Getting Started 2
Basic Operation 2-1
Menu 2-2
Description of Keypad and Soft Keys 2-2
Display Conventions 2-3
Self-Test and Data Screen 2-4
Choosing User or Administrator Operation 2-5
Software 2-6
Connections 3
Connecting AC Power or a Car Adaptor 3-1
CompactFlash Card 3-1
Batteries 3-2
Ethernet Connection for Data Output 3-3
Specifications 4
Safety Considerations 5
Environmental Conditions for Normal Use 5-1
Cleaning Instructions and Precautions 5-1
Warning Markings and Symbols 5-1
Recycling 6
General Operation 7
Turning the Unit On and Off 7-1
Search Modes 7-1
Audible Search Setting 7-5
Taking a Background 7-5
Identifying Sources of Radiation 7-7
Analysis Report 7-8
Storing, Reviewing and Retrieving Spectra 7-9
Manual Calibration 8
Coarse Calibration 8-1
Dose Rate and Fine Energy Calibration 8-3

System Menus 9
Introduction 9-1
Run a Procedure/Display Information/Open Submenu 9-2
Check Option On or Off 9-2
Adjust Slider 9-2
Select Among Options 9-3
Isotope List 9-3
Edit Numeric Value 9-4
Edit Date for Filter 9-5
User Menus 9-5
Field Settings 9-5
Spectral Data 9-8
Configuration 9-10
Help Menu 9-11
Administrator Menus 9-12
Configuration (Extra Items) 9-12
Admin 9-13
Factory Settings 9-17

Model 702e, 703e, 711e Technical Manual Section 1
Ludlum Measurements, Inc. May 2019
1-1
Introduction
About Your Model 700e Series Unit
The Ludlum Model 700e series includes the Model 702e, 703e and 711e. They are portable
radioisotope identification (RID) systems that detect and identify multiple nuclides, providing
quantified results using time-slice analysis.
The 700e series of instruments use an externally housed NaI detector. The external detector
eliminates the need for an embedded source to provide gain stabilization and self-calibration and
allows for meeting ANSI N42.34 standard.
The instruments can be operated either in a very simple mode requiring no previous experience or in
other operating modes that take advantage of the comprehensive set of advanced features.
The Model 700e units offer two log-on modes: User and Administrator. The User functions allow
first-line responders to perform all the tasks needed in the line of duty. The Administrator
functions allow a health physicist, or other expert, to set up the device for specific applications and
to perform additional maintenance functions. This manual will cover aspects of both, but places an
emphasis on User functions.
CAUTION! It is important to limit access to Administration Mode to those who are
qualified to use it. This mode includes the advanced functions of the instrument and
allows the user access to everything. The general user should be limited to User
Mode only. If any of the advanced functions are altered incorrectly, it could affect the
overall function of the instrument and may require expensive re-calibration. Please
see Section 2, starting with page 2-5, for details on how to set up the Administration
Mode and protect the mode with a password.
Once you set a password for the Administration Mode, it is important not only to
keep it private, but to not lose it or forget it. If the password is forgotten, it can only
be reset by the factory.
In addition, do not alter calibration settings, or it may incorrectly alter the
instrument’s functions and require repair by the factory.
After logging on, the device powers up in an initial search mode. Several different views of this
mode are available, but all are based on data collected in real time. In addition to the search modes,
setup, alarm review, and calibration functions can be accessed through the menu system.
The instrument has a simple user interface and a wide range of setup functions and utilities.
Section
1

Model 702e, 703e, 711e Technical Manual Section 1
Ludlum Measurements, Inc. May 2019
1-2
The Model 700e series unit can be connected to a remote computer using an Ethernet cable, and
accessed with either Quantum™ MCA (standard) or Quantum™ Gold (quantitative analysis)
software. The Quantum™ software allows:
Up to eight MCAs to be controlled at one time, with full spectrum data in real time.
Unit analysis in 256 QCC or linear, 512 QCC or linear, and 1024 linear modes.
Note that if you are using either instrument without a PC, operation is limited to 256 and 512 QCC,
including the saving of spectra. However, while under control of Quantum software, all ADC modes
(including 1024 linear) are available.
The basic Model 700e series unit consists of:
The spectrometer electronics
External gamma ray detector
An AC power adapter
Ethernet connectivity for remote operation
Compact flash card spectra storage
Optional devices include:
Quantum software
A car power adapter

Model 702e, 703e, 711e Technical Manual Section 2
Ludlum Measurements, Inc. 2-1 May 2019
Getting Started
Turn on the Model 700e series unit (referred to for the remainder of this manual as the Model 702e)
by holding down the power key (which is also the BACK key) until the status screen appears.
Press ENTER to move to the log-in screen, and then press ENTER () again to advance to the user-
mode search screen (generally Dial). At the bottom of the screen there will be a message indicating
auto calibration is in progress. This may take one to three minutes. The instrument is then ready for
use.
Basic Operation
Refer to the following screen drawing, where three soft keys will be seen (Identify, Background,
Finder). These are accessed by the LEFT () or RIGHT () arrow keys and then pressing ENTER.
The far right soft key allows the user to select between the available search modes. The Dial and
Finder screens are the simple modes of operation where the Dial gives count rate information in the
form of a speedometer. When radioactive material gives an indication in the green region, this
signals proper source intensity for identification with gamma count rate. The other colored regions
indicate the source is too far (gray) or too close (red). The Finder mode allows location of the
source by displaying intensity vertically and time horizontally. The midscale “ID” shows the proper
intensity for identification. In addition, an audio signal can aid in finding the source. The other two
search modes (Bars and Spectrum) are more advanced and must be enabled in the administrator
menu. These two screens allow the user to view isotopes in the form of vertical “Bars” or a
“Spectrum,” where the isotope is identified or its presence is seen in real time. These modes also
give isotope category and dose rate in real time.
Identification may be performed in any one of the four modes. Simply highlight the Identify soft
key and press ENTER. A report appears after the acquisition period. Isotopes identified are shown
with a statistical confidence number ranging from 0 to 100%. This is based on source strength,
length of acquisition, number of energy lines, and statistical factors. The default for taking a
background or acquiring a spectrum is one minute. The length of acquisition can be increased or
decreased by pressing ENTER when the soft key is on ±30 seconds. If ENTER is held down, the
length of time can be changed rapidly. Pressing the BACK key allows the user to return to the search
modes. Holding down the BACK / power key for a count of three seconds turns the instrument off.
Section
2

Model 702e, 703e, 711e Technical Manual Section 2
Ludlum Measurements, Inc. 2-2 May 2019
Menu
Coarse calibration, review of stored spectra, thresholds, and many other features can be accessed
from the user or administrator (password protected) menu. The menu can be accessed from any
one of the search modes.
Description of Keypad and Soft Keys
Figure 1 shows a rendering of the Model 702e keypads. Some of the keys are located underneath the
display, while the most commonly used keys are located on the handle.
Figure 1 – Model 702e Keypad
The following is a brief description of the seven keys and how they are used.
BACK/ Returns to previous screen, exiting from menu or report. This key is also used to
turn system power on and off.
MENU Enters the menu system from any search screen.
ENTER Used to select currently highlighted option, such as a soft key or a menu item and
also used to continue to next step of multi-step processes.
and These keys will be referred to throughout the text as LEFTand RIGHT. They are
used to select among the soft-key options or menu tabs, to move backward and
forward in a string entry process, to select among items in a menu choice process,
and for various other applications that will be described later in the document.
and These keys will be referred to as UPand DOWN. They are used to scroll among
menu items, to scroll through reports, to change the current letter when entering a
string such as a password, and for various other applications that will be described
later in the document.

Model 702e, 703e, 711e Technical Manual Section 2
Ludlum Measurements, Inc. 2-3 May 2019
Many of the common operations of the Model 702e are performed using “Soft Keys.” These are
represented by a set of words in a gray bar shown at the bottom of the screen. In Figure 2, the
normal soft keys seen in the “Dial” search screen are shown. The Identify soft key is currently
selected. By pressing the LEFT and RIGHT keys, you can move the highlighting among the other
soft keys, Background and Finder. Pressing the ENTER key will perform the action specified by
the currently highlighted soft key, for example, entering the identification mode to collect, report,
and store an analysis of a possible radioactive substance.
Figure 2 - Example of Soft Keys
Display Conventions
In order to make the Model 702e more friendly and easy to use, we have defined several color and
layout conventions for the user interface.
Four different nuclide “classes” are defined by their colors, which appear as labels and as
filled-in areas in spectra. Blue is for industrial (IND), magenta for special nuclear materials
(SNM), cyan for medical (MED), and green for naturally occurring radioactive materials
(NORM or NRM). In addition, when there is insufficient data to be sure something is
present, it will be marked in yellow for uncertain (UNC). When there is something definitely
present but not matched to any currently enabled nuclide, it will be labeled in red for
unknown (UNK).

Model 702e, 703e, 711e Technical Manual Section 2
Ludlum Measurements, Inc. 2-4 May 2019
In other contexts, red is used to signal bad conditions (dead battery, calibration failure,
dangerous dose rate); yellow and orange indicate concern (battery nearing end of life,
calibration incomplete); and green indicates everything is normal (battery good, calibration
done, OK to ID).
Soft keys are always displayed at the very bottom of the screen in shades of black and white.
In most cases, where possible, small arrows are shown on the currently selected item to
indicate possible choices. For example, on a selected menu tab, you can go LEFT or RIGHT
or DOWN into the menu. For some menu items, you may be able to use LEFT and RIGHT to
change the value. Two examples are shown here.
Different colors are used to group the items in each of the main menus. All sub-menus (the
menus that come up within an operation selected from the menu system) are displayed in
shades of gray and white. The shading serves to remind you that if you exit from this menu
with the BACK key, it will only take you back to the higher level menu.
Self-Test and Data Screen
When the Model 702e unit is first powered on, you will see a screen that shows the results of an
initial power-on self test, or “POST.” A properly functioning unit will have a display similar to that
shown in Figure 3. The internal case temperature may vary, and your estimated battery life will
change as batteries are charged and discharged. Press ENTER to continue to the log-in screen.
Figure 3 - Successful POST Screen

Model 702e, 703e, 711e Technical Manual Section 2
Ludlum Measurements, Inc. 2-5 May 2019
Choosing User or Administrator Operation
Immediately after the self-test screen, a log-in screen appears, as shown in Figure 4. On this screen
you have the option of logging in as the User or Administrator. The User functions allow first-
line responders to perform all the tasks needed in the line of duty. The Administrator functions
allow a health physicist or other expert to set up the device for specific applications, and to perform
additional maintenance functions.1The User mode can generally be accessed without a password,
while the Administrator mode requires a password to be entered.
Figure 4 – Log-in Screen with User Selected
Figure 5 – Log-in Screen for Administrator with Password
1These modes are designed to comply with ANSI N42.34 Routine and Restricted modes and IAEA Pub
1240 Easy and Expert modes.

Model 702e, 703e, 711e Technical Manual Section 2
Ludlum Measurements, Inc. 2-6 May 2019
When entering a password, as shown for the Administrator in Figure 5, use the UPand DOWN
arrows to change the letter, and the LEFT and RIGHT arrows to move within the word. Holding
down the UPor DOWN arrows will rapidly scan through the alphabet. The word is displayed on the
screen, otherwise it would be impossible to determine what letter is being entered! To ensure
confidentiality, enter the password while no one else can see the screen.
Software
The Quantum™ software is a useful tool for advanced users seeking additional analytical capabilities
for their Model 702e spectra. The Quantum software is supplied in two basic configurations,
Quantum MCA and Quantum Gold.
Quantum MCA, a subset of Quantum Gold, is the "standard" software and provides qualitative, but
not quantitative analysis. Qualitative analysis will allow analyzing for the type of isotope present, but
not how much of each isotope is present. Certain features, such as background subtraction, are
considered part of the quantitative analysis package and are not available in Quantum MCA.
Quantum Gold supports both quantitative and qualitative analysis, and is the software the Quantum
software manual is written for.

Model 702e, 703e, 711e Technical Manual Section 3
Ludlum Measurements, Inc. 3-1 May 2019
Connections
The Model 702e units have two external connectors for power, communications, and other
functions. In the back right-hand corner is a watertight connector that provides AC power. There is
a flexible, rubber port cover at the top front, and behind it are a CompactFlash slot on the left and
an Ethernet connector on the right.
Connecting AC Power or a Car Adaptor
A universal (110-240 V, 50/60 Hz) AC power supply is supplied for your unit. This power supply
will run the unit and charge the internal batteries, and connects directly to the watertight connector.
The other model requires an adapter cable, which plugs into the watertight connector. Then the
AC power supply plugs into a mating plug on the adapter cable.
The car adapter plugs into a 12-volt accessory outlet or “cigarette lighter” outlet in your vehicle. It
then connects to the watertight connector on the unit.
CompactFlash Card
Your unit comes with a CompactFlash card that serves the following purposes:
Storage for a nearly unlimited number of spectra in ANSI standard (N42.42) format.
Storage of specific system configuration information.
Easily upgradeable system firmware.
Section
3

Model 702e, 703e, 711e Technical Manual Section 3
Ludlum Measurements, Inc. 3-2 May 2019
Do not remove the CompactFlash card while the system is turned on. The system will not continue
to operate without the card in place. It is best to turn the unit off, remove the card, perform
whatever activities are needed, and reinsert the card before turning the unit back on. Also, it is
important to note that this card is
specific to your unit and detector
. In fact, the serial number of
the electronics and detector is printed on your particular CompactFlash card. Because each unit is
factory calibrated for optimal performance, and this calibration is stored on the CompactFlash card,
the cards should never be exchanged between different units. Also, the contents of the card should
not be erased, except through the menus provided in the unit itself.
You may wish to read the saved spectral information on the card using your PC. If your PC
includes a media reader bay, you should be able to insert the card and read it as simply as you would
access a CD-ROM or floppy. If your PC does not have a media reader built in, a simple USB
interface is available as an accessory. In either case, the device will be assigned a drive letter, often
E: or F: (we will assume E: throughout this document). The spectra may then be read from the
directory E:\spectra.
Batteries
Your Model 702e unit comes equipped with eight internal rechargeable AA batteries. These
batteries are normally charges by plugging in the external charger. Access to the battery
compartment requires removal of the lower enclosure.
Depending on usage, the Model 702e unit will generally run six to eight hours on a single charge
when the recommended batteries are used. There are several ways to improve your battery life:
Reduce the display brightness as low as possible without affecting your ability to read the
display. If operating out-of-doors, you may find that the reflected sunlight is sufficient to
read the display even with the brightness at its minimum setting.
Turn off the Audible Count Rate and/or Mute the speaker.
Shorten the Backlight Timeout so the display darkens when you are not using the system.
Use AC power when connecting to a PC or doing other stationary operations in the office.
The unit will automatically run from AC power if it is available.

Model 702e, 703e, 711e Technical Manual Section 3
Ludlum Measurements, Inc. 3-3 May 2019
Ethernet Connection for Data Output
In addition to accessing data directly on the CompactFlash card, the Ethernet connector can be used
to connect your unit to a building network or to your PC. By making this connection, you will be
able to access data on the unit, including operating it remotely with the Quantum™ software.
If you are connecting to an Ethernet switch or hub, a standard CAT-5 Ethernet cable can be used.
If you wish to connect directly to your PC, you will need a special “crossover” cable that takes the
place of the switch or hub. Both of these are available as accessories.
1. Connect the Model 702e unit to the local Ethernet using a CAT-5 or Ethernet cable, available as
an accessory for your unit.
A. If connecting to a hub or switch, use a standard or “straight through” Ethernet cable.
B. If connecting directly to a PC, use a “crossover” Ethernet cable.
2. Connect the other end of the cable to the host computer, hub, or switch.
3. Power on the Model 702e unit and log in as the Administrator.
4. Press the MENU button key to go to the menu, and move right to select the Admin menu.
5. If this is your first time using Ethernet communications from this unit, or you have moved the
unit to a new network, you may need to enter information into the Network Setup. Otherwise,
you will only need the IP address setting of the Model 702e unit for use in step 8 below.
6. Move down to select the first item, Remote Mode. Press the ENTER key to select remote
operation.
7. Click on the Quantum™ hardware search icon to open the MCA Devices Auto
Configuration program.
8. Select Ethernet, ANS Ethernet, and Quantum Ethernet. Enter the IP address given to you
by your system administrator or entered in Step 5.
9. Click the Update button. If the connection is successful, the version number and serial number
will display on the MCA Devices Auto Configuration screen.
In addition to the reference information found in the Quantum software manual, detailed startup
and calibration procedures can be found in the supplemental application notes in the "DOC" folder
on the Quantum CD. Both PDF versions (for quick, on-screen reading) and Word documents (for
better printing) are included. Start with the application note "QtmInitialCalibration," which includes
software installation notes and hardware connection information.

Model 702e, 703e, 711e Technical Manual Section 4
Ludlum Measurements, Inc. 4-1 May 2019
Specifications
Preamplifier
Type: Charge Sensitive
Input: Negative Current (anode)
ADC
Type: 14-bit pipelined
Speed: 50 MHz
Pulse Processing
Type: Digital, Trapezoidal Shaping
Peaking times: 40 ns to 5.1 µs, factory set to 1.28 µs
Gain: Digital, 0.5x to 16x
LLD: 0 to 100% of full scale, digitally adjustable in .01% intervals
ULD: 0 to 100% of full scale, digitally adjustable in .01% intervals
Zero: -5% to +5% of full scale, digitally adjustable
Spectrum Conversion
Collection Mode: Linear – 16384 Channels
Conversion Modes: Linear – 256, 512, 1024 Channels
QCC – 256, 512 Channels (U.S. Patent 5,608,222)
Note: If you are using the instrument without a PC, operation is limited to
256 and 512 QCC, including the saving of spectra. However, while
under control of Quantum software, all ADC modes (including 1024
linear) are available.
System Controller
Processor: PPC405 CPU at 50 MHz
Display: 320 x 240 high contrast 32,000 color display with LED backlight
Controls: 7-key custom keypad
I/O: RJ-45 Ethernet port for computer connection
ENP3 series watertight connector for power and other functions
Clock: Battery backed-up clock/calendar
Section
4