Lufft XP100 User manual

www.lufft.com
a passion for precision · passion pour la précision · pasión por la precisión · passione per la precisione · a passion for precision · passion pour la précision · pasión por la precisión · passione per la precisione · a passion for precision · passion pour la précision · pasión por la precisión · passione per la precisione ·
User Manual XP100 / XP101
X(pert) P(rofessional) Series

EN Operating manual – temperature measuring device XP100 / XP101 1
11_2014
Preface
The operating manual only describes the temperature measuring
device and its intended use.
Detailed descriptions of the sensors and optional accessories as
well as tips for proper and practical use of the temperature
measuring device are not included in this operating manual.
The current version of the operating manual and the general
catalogue can be found at: www.lufft.de
Symbols
Hazardous electric current!
Warns about hazards from electric current which can
lead to injuries or even death.
Danger!
Warns of a hazard which can lead to personal injury.
Caution!
Warns of a hazard which can lead to damage to
property.
Definitions
Legal notice
This release replaces all previous versions. No part of this
publication may be reproduced without written permission from
Lufft®. The same applies for electronically processing,
duplicating or spreading the publication. Subject to technical
changes. All rights reserved. Trademarks are used without
guarantee that they may be used freely and primarily following
the spelling of the manufacturer. Product names are registered.
Changes to construction in the interests of constant
improvements to the product, as well as changes to the shape
and colour are reserved.
The scope of delivery may vary from product images. This
document was created with all due care. Lufft®accepts no
liability whatsoever for possible mistakes or omissions.
The only party responsible for determining measured results to be
valid, drawing conclusions and deriving actions is the user! Lufft®
accepts no claims of warranty for correctness of detected
measured values or measured results. Further, Lufft®accepts no
liability whatsoever for possible mistakes or damage which have
been caused by utilising the detected measured results. © Lufft®
Warranty
The warranty is for 12 months. Damages caused by incorrect use
by untrained people or start-up by unauthorised people are
excluded from the warranty.
The device complies with the fundamental health and safety
requirements of the applicable EU regulations and was tested at
the factory for perfect functionality multiple times. However, if
faults in the functionality occur and cannot be remedied with the
measures in the chapter Errors and faults, please get in touch
with your dealer or distributor. When making a warranty claim,
supply the device number (see the rear of the device). The invoice
acts as warranty certificate. When manufacturer's instructions or
legal regulations have not been followed, or after unauthorised
changes to the device are made, the manufacturer is not
responsible for the resulting damages. Changes to the device or
unauthorised replacement of individual parts can drastically
impact the electrical safety of this product and leads to the forfeit
of the warranty. Liability does not extend to damages to people or
property caused by the device being used other than as described
in the instructions in this operating manual. Subject to changes to
technical design and model changes as part of constant
development and product improvement without prior notice.
No liability is accepted for damages resulting from improper use.
In such cases, entitlements to a warranty are then also forfeited.
Table of contents
Notes regarding the operating manual .................................... 01
Information about the device................................................... 02
Technical data ........................................................................ 03
Safety ..................................................................................... 04
Transport and storage............................................................. 04
Operation................................................................................ 05
PC software ............................................................................ 14
Errors and faults ..................................................................... 14
Maintenance........................................................................... 15
Disposal.................................................................................. 16
Declaration of conformity ........................................................ 16
Notes regarding the operating manual
Concept Meaning
SmartGraph3 PC software for analysis and visualisation of
measured values

2Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Description of the device
The temperature measuring device XP100 / XP101 is used for
carrying out accurate measured value detection. To do so, you
can connect different temperature probes of type PT1000 to the
device interface.
The operating elements are found on the front and sides of the
robust housing. A scratch-proof colour display with touch
function (1) allows entering and selecting values and functions
and also displaying detected results. You can also navigate the
device software by using the cross control (3) and the OK
button (5) and select measuring functions.
By pressing the Back key (2) you return to the previous screen of
the device software. Pressing the Menu key (6) directly opens the
main menu.
Pressing the Illumination key (4) either switches the background
illumination for the colour display and the keys on or dims them.
Located above the colour display (1) is the connection for the
digital sensors (7). Here you can connect the sensor. The
measured results of the connected sensor are shown in the
device's colour display (1).
The On/Off key (9) and a USB connection (10) are found on the
sides of the device.
You can connect the device to a computer by using the supplied
USB connection cable. Then you can extract and analyse your
measured results with the SmartGraph3 software.
Device depiction
Information about the device
No. Operating element
1 Scratch-proof colour display with touch function
2 Back key
3 Cross control with Up, Down, Left, Right keys
4 Illumination key
5 OK button
6 Menu key
7 Connection for PT100 sensors (4-pin)
8 Battery compartment with battery cover
9 On/Off key
10 Micro USB connection
1
2
3
4
5
6
7
8
910

EN Operating manual – temperature measuring device XP100 / XP101 3
11_2014
XP100 accessories
•Bag/case
• Temperature probe PT100
• Sensor cable: 2 m or 10 m length
• Plug to connect the temperature probe PT100
•USBpowersupply
• Connector plug for PT100 temperature probe
For further information please contact your Lufft®customer
service.
Accuracy
XP100 scope of delivery
Scope of delivery includes:
• 1 x XP100
• 1 x USB cable
• 4 x Alkaline LR6 AA, 1.5 V batteries
• 1 x Getting started guide
• 1 x Factory test certificate
XP101 scope of delivery
Scope of delivery includes:
• 1 x XP101 with stored sensor characteristic curve for the
supplied probe
• 1 x Temperature probe PT100, type 3120.700, aged and
calibrated
• 1 x Sensor cable of 2 m length
• 1 x USB cable
• 4 x Alkaline LR6 AA, 1.5 V batteries
•1xTransportcase
• 1 x Getting started guide
• 1 x Factory test certificate
• 1 x DAkks / DKD calibration certificate (German accreditation
bodies)
Technical data
Parameter Value
Temperature probe PT100 according to DIN EN 60751
Measuring range -200 °C to +850 °C
Resolution 0.001 K
Electrical accuracy
at 10 °C to 30 °C
ambient temperature
0.01 K at temperatures ≤0 °C at the sensor
0.01 K + 0.00005 * temperature in °C
at temperatures > 0 °C at the sensor
System accuracy (XP101) 5 mK at 0 °C; 20 mK (-40 °C...+200 °C)
(individual determination of the sensor char-
acteristic)
Measuring circuit 4-wire
Measuring current normal
operation 1 mA DC with duty factor 50 % = 0.50 mA 1.85 measurements /s
Measuring current root 2
function 1 mA DC with duty factor 33 % = 0.33 mA 1.25 measurements /s
Elimination of
thermoelectric voltage yes, automatically
Operating temperature 0 °C to +50 °C (with < 90 % RH)
Storage temperature -20 °C to +60 °C (with < 95 % RH)
Battery type 4 x Alkaline LR6 AA, 1.5 V batteries
Power consumption
(with illumination) approx. 40 mA
Dimensions
(length x width x height) 127 x 83 x 42 mm
Weight 290 g
Memory for approx. 200 measuring projects consisting
of up to 3 x 3600 (=10,800) measuring points,
that is a total of 200 x 10800 = 2160000
measuring points
Display touchscreen, capacitive, TFT,
resolution 240x320, 65535 colours,
sunlight-readable
Power input active approx. 400 mW
Battery lifespan passive approx. 1 year
Battery lifespan active at least 24 hours
Resolution to 3 decimal places
-0,06
-0,04
-0,02
0
0,02
0,04
0,06
-200 0 10 20 30 40 50 100 200 300 400 500 600 700 800 900
precision in °C
temperature of the measuring object in °C
electr. precision at 10°C ... 30°C ambient temperature
-0,15
-0,1
-0,05
0
0,05
0,1
0,15
-330 32 50 70 90 110 130 210 400 600 800 1000 1200 1400 1600
precision in °F
Temperature of the measured object in °F
electr. precision at 50 ... 90°F ambient temperature

4Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Carefully read the operating manual before using the device
and keep it within reach!
• Do not use the device in atmospheres containing oil, sulphur,
chlorine or salt.
• Never use the device for measurements at live parts.
• Ensure that all connection cables are protected from
damages (e.g. from kinks or crushing).
• Protect the device from permanent direct sunlight.
• Observe the storage and operating conditions (see chapter
Transport and storage).
Intended use
Only use the thermometer XP100 / XP101 for temperature
measurements in dry surroundings. In doing so, observe the
technical data.
To use the device for its intended use, only connect and use
accessories and spare parts which have been approved by
Lufft®.
Improper use
Do not use the device in potentially explosive areas. Lufft®
accepts no liability for damages resulting from improper use. In
such a case, entitlements to a warranty are forfeited. Any
unauthorised modifications, alterations or structural changes to
the device are forbidden.
Personnel qualifications
People who use this device must:
• have read and understood the operating manual, especially
the Safety chapter.
For maintenance or repair work which requires the housing
to be opened, contact Lufft®customer service. Devices
which have been opened unlawfully are void of any warranty
and warranty claims.
Residual risks
Danger!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.
Danger!
The device is not a toy and does not belong in the hands
of children.
Danger!
Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way.
Observe the personnel qualifications.
Caution!
To prevent damages to the device, do not expose it to
extreme temperatures, extreme humidity or moisture.
Caution!
Do not use abrasive cleaners or solvents to clean the
device.
Transport
Use a suitable bag to transport the device safely.
The XP101 is delivered with a transport case.
Storage
When the device is not being used, observe the following storage
conditions:
•dry,
• protected from dust and direct sunlight,
• with a plastic cover to protect it from invasive dust, if
necessary.
• The storage temperature is the same as the range given in
the chapter .
• When storing the device for a long time, remove the batteries.
Safety
Transport and storage

EN Operating manual – temperature measuring device XP100 / XP101 5
11_2014
Inserting the batteries
• Insert the supplied batteries before first use.
Caution!
Make certain that the surface of the device is dry and the
device is switched off.
1. Open the cover of the battery compartment (8).
2. Insert the batteries with correct polarity.
3. Close the cover of the battery compartment (8).
– The device can now be switched on.
Switch-on
1. Press and hold the On/Off key (9) for approx. 3 seconds until
a beep is emitted.
2. Let go of the On/Off key (9).
– The colour display is switched on. The device is ready for
operation as soon as the main menu is shown.
Switch-off
1. Press and hold the On/Off key (9) for approx. 3 seconds until
a beep is emitted.
2. Let go of the On/Off key (9).
– The device will be switched off.
Description of screen elements
When using the device, take special note of the following
important operating elements and displays:
• The Back key (2) opens the previous menu.
• The Menu key (6) opens the main menu.
• Name of the current screen (15).
• Display of the current time (11).
• The padlock symbol (12) appears when you press and hold
the On/Off key (9) for approx. 1 second during a
measurement. The touch function of the colour display is
locked. To release the lock, press and hold the On/Off key (9)
for approx. 1 second.
• The lightbulb symbol (13) appears when you have used the
Illumination key (4) to switch on background illumination.
• Battery level indicator (14); a plug symbol is shown when
power is supplied via a USB connection.
All options which can be selected via touch function can also be
selected by using the cross control and the OK button (5).
For safety reasons, some options can only be selected and
configured by using the cross control and the OK button (e.g. date
and time in the Settings screen).
Operation
8
2
6
15 14
131211

6Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Set language
1. Press the Menu key (6) to open the main menu.
2. Press the Settings button in the main menu.
3. Press the language selection button (16) in the Settings
screen.
4. Press the button with the desired language from the following
screen.
– The selected screen language is activated immediately.
5. Press the Back key (2) to return to the desired measuring
mode. Alternatively press the Menu key (6) and then the
Measuring mode button.
Main menu
You can open the following menus from the main menu:
2
6
16
Measuring mode: Perform measurements with the connected sensor.
Archive: Open archived measured values.
Settings: Make any device settings.

EN Operating manual – temperature measuring device XP100 / XP101 7
11_2014
Archive screen
In the Archive screen, you can view archived measuring projects
or open them for further processing:
Archive, fig. A.:
The icons beside the saved measuring projects show each
measuring mode (see examples in fig. A.). The meaning is as
follows:
Archive, fig. B.:
A.
20
21 22
20 Shows the measuring projects which are saved in the archive.
The currently selected archive entry is highlighted.
Navigate in the archive as follows:
1. Press the Down key on the cross control until the desired archive
entry is selected.
2. You may need to turn the page by pressing the Left or Right keys on
the cross control.
3. Press the OK button on the cross control to confirm the selected
archive entry. You can also press OK (21) on the screen. Fig. B.
opens.
21 Selects the currently selected archive entry. => Fig. B. opens.
22 Deletes all entries from the archive. A safety prompt opens. Confirm
it by pressing the OK button if you want to delete all entries. Otherwise,
touch the Cancel button.
Spot measurement
Time measurement
B.
23
24
25
23 Opens the selected archive entry (see fig. C.).
24 Deletes the selected archive entry. A safety prompt opens. Confirm it
by pressing the OK button if you want to delete the entry.
Otherwise, touch the Cancel button.
25 Closes fig. B. and returns to fig. A.

8Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Archive, fig. C.:
C.
27
26
26 Charts (top of fig.°C.) and tabulates (bottom of fig.°C.) the measured
values.
Displayed in the table are the minimum value (MIN), the maximum value
(MAX), the arithmetic average (∅) and the standard deviation (SD).
In case the data does not fit onto one table page after a longer recording
session, you can browse through the timeline ([s], on the right in fig. C.)
by using the Left and Right keys on the cross control unit.
27 Closes the selected archive entry and returns to fig. A.

EN Operating manual – temperature measuring device XP100 / XP101 9
11_2014
Settings screen
You can configure the device as follows in the Settings screen:
Settings 1/3:
Settings 2/3:
16
28
29
30
31
16 Selects the screen language (see chapter Set language).
28 Selects the unit system:
Metric: Activates the metric unit system for all available meas-
ured values (e.g. for use in continental Europe).
Imperial: Activates the imperial unit system for all available
measured values (e.g. for use in the USA).
29 Sets the screen brightness.
This option can only be selected by using the cross control below the
colour display.
1. Repeatedly press the Down key on the cross control until the scale is
selected.
2. Press the Left or Right keys on the cross control to reduce (left) or
increase (right) the screen brightness.
30 Sets the date and time.
This option can only be selected by using the cross control below the
colour display.
1. Press the Down key on the cross control until the date is selected.
2. Press the OK button on the cross control.
The entire row is selected.
3. Press the Left or Right keys on the cross control to select the value to
be configured.
4. Press the Up or Down keys on the cross control to increase or reduce
the value to be configured.
5. Press the OK button on the cross control.
The row is deselected.
31 Opens the next screen.
32
33
34
35
32 Either specifies the period for automatic dimming of the colour display
or deactivates the function:
30 seconds, 1 minute, 5 minutes, off
33 Either specifies the period for automatic switch-off of the colour display
or deactivates the function:
10 minutes, 30 minutes, 1 hour, off
Note!
This function is deactivated during an automatic measurement.
34 Switches signal tones/key tones on or off.
35 Opens the next screen.

10 Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Settings 3/3:
36
37
38
A.
39
B.
C.
D.
36 Configures the duty factor at the sensor:
normal duty factor 50 %
sqrt(2) duty factor 33 %
Changing the duty factor enables the determination of the
sensor's self-heating. This measuring method can be used for
high-precision measurements at fixed points, such as the
water triple point, and in suitable media ensuring a high
temperature stability.
The selected setting is displayed on the screen if it differs from the setting
Normal.
37 Here, the linearisation function can be selected. The following options are
available:
IEC 60751 default setting for PT100
ITS-90 for spectrally pure platinum resistance thermometers
XP101 Only available for the XP101. Contains stored characteristic
curve for the supplied sensor
Note!
Before using the measuring device, make sure that you are aware of the
device's intended purpose and the respective standard in effect as well as
the contents of this standard.
38 Here, different coefficients can be selected and entered by hand. Once
you changed the coefficient, *U is displayed behind the selected
linearisation function in the measuring mode.
The coefficient selection options depend on the selected linearisation
function. Indicated below are the editable coefficients with their default
values:
IEC 60751
R0= 100 
A = +3.9083*10-3 °C-1
B = -5.7750*10-7 °C-2
C = -4.1830*10-12 °C-3
ITS-90 For explanations regarding ITS-90 see below.
XP101 The coefficients for this function cannot be edited.
Note!
Incorrect coefficients can lead to large measurement deviations!
Change the value for a coefficient as follows:
1. Click on the Coefficients button.
2. Press the button with the desired coefficient (see fig. B. for IEC 60751
or fig. C. for ITS-90).
3. Enter the desired value by use of the buttons (example fig. D.)
4. Confirm the entry by pressing OK.
5. To reset a default value, press the recycle bin icon.
Note!
This function is not available if XP101 was selected as linearisation
function.
39 Offset Offset value range: -10 °C to +10 °C
Once you changed the offset, *U is displayed behind the selected
linearisation function in the measuring mode. The offset value is added to
the measured temperature value.
Note!
This function is not available if XP101 was selected as linearisation
function.

EN Operating manual – temperature measuring device XP100 / XP101 11
11_2014
Explanations regarding ITS-90:
Calculation of the deviation to the reference function W:
W corresponds to the sensor's current resistance divided by the sensor's
resistance at the water triple point (0.01°C).
a1) If W < 1 and cL1 = 0 (for the range from -190°C to 0.01°C):
In that event the parameter cL1 is bracketed in the selection: (cL1)
∆W = aL[W - 1] + bL[W - 1] ln W
Default setting:
aL = 0; bL = 0; cL1 = 0
a2) If W < 1 and cL1 ≠ 0 (for the range from -219°C to 0.01°C):
In that event the parameter cL1 is displayed as usual in the selection: cL1
∆W = aL[W - 1] + bL[W - 1]2+ cL1[ln W ]2
b) If W >= 1
∆W = aH[W - 1] + bH[W - 1]2 + cH[W - 1]3+ dH[W - W Al)]2
Default setting:
aH = 0; aH = 0; cH = 0; dH = 0; W-Al = 3.3760086
Measuring mode screen
A.
B.
40
42
43
44 45 46 47
41
40 Indicates the current temperature value.
41 Displays information on the current measuring mode and the character-
istic curve.
42 This symbol indicates, that the displayed measured values under 43 are
calculated (e.g. minimum/maximum measured value).
43 Indicates the calculated measured values according to the selection
(e.g. minimum/maximum measured value).
44 Sets the measured values displayed under 43 and the duration back to
zero.
45 Specifies how the measured values under 43 are shown (see fig.
B.):
Minimum: Always shows the smallest detected measured value
from a measuring period.
Maximum: Always shows the largest detected measured value
from a measuring period.
Average: Shows the average value of all measured values which
have been detected so far from a measuring period.
Hold: Pauses the current detected measured value and
shows it continually (when this option is selected).
Off: Switches the display (42) off.
46 Carries out an automatic measurement for the duration of an already
specified recording interval. The recording interval can be specified in
the following screen (see fig. C. and fig. D.).
47 Saves the currently displayed measured value as single measurement
in the archive with date and time stamp.

12 Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Measuring mode – Automatic measurement screen
C.
D.
48
49
50 51 52 53
48 Shows the measured temperature value.
49 Shows the remaining time until the automatic measurement finishes.
50 Opens a screen for selecting the recording duration (see fig. D.).
51 Starts recording.
The key turns red once recording has started.
Note!
During an active recording it is not possible to switch off the measuring
device with the On/Off key. Automatic switch-off is also deactivated.
First stop the recording by pressing key 52 and then turn off the device.
52 Stops the current recording. The detected values are automatically
saved to the current measuring project.
53 Pauses the current recording.
Key 51 continues to be illuminated in red.
Press key 53 again to resume recording.

EN Operating manual – temperature measuring device XP100 / XP101 13
11_2014
Carrying out a measurement
Note:
Note that moving from a cold area to a warm area can lead to
condensation forming on the device's circuit board. This physical
and unavoidable effect can falsify the measurement. In this case,
the colour display shows either no measured values or they are
incorrect. Wait a few minutes until the device has become
adjusted to the changed conditions before carrying out a
measurement.
Upon connection of a sensor the devices changes into the
measuring mode. The corresponding screen is displayed and the
measurement begins.
Shut down procedure
1. Use the On/Off key (9) to switch the device off.
2. Detach connecting cables and sensors.
3. Clean the device according to the chapter Cleaning the
device.
4. Store the device according to the chapter Storage.
A.
B.
C.
D.
E.

14 Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Use the SmartGraph3 PC software to carry out a detailed analysis
and visualisation of your measured results. Only by employing
this PC software can all options of the measuring device for
visualization and functioning be utilized (e.g. data export into an
Excel/PDF file or data output in form of a printout).
Installation conditions
Ensure that the following minimum requirements for installing the
SmartGraph3 PC software are fulfilled:
• Supported operating systems (32 or 64 bit version):
–WindowsVista
–Windows7
–Windows8
• Software requirements:
– Microsoft .NET Framework (is automatically installed
during the software installation, where applicable)
• Hardware requirements:
– Processor speed: min. 1.6 GHz
–USBconnection
– 2 GB RAM, minimum
– 1 GB hard disk space, minimum
Installing the PC software
1. Download the current PC software from the Internet. To do
so, visit the website www.smartgraph3.de/download.
2. Double-click the downloaded file.
3. Follow the instructions of the installation wizard.
Starting the PC software
1. Start the SmartGraph3 software.
2. Switch the device on, if required.
3. Connect the device to your PC via the USB connection cable
provided in the scope of delivery. After a few seconds (up to
one minute) the device is automatically detected and added
to the device list in the SmartGraph3 software.
Information about using the PC software is provided in the online
help.
The accurate functionality of the device was tested during
production a number of times. However, if functionality faults do
occur, then check the device according to the following list.
The device does not switch on:
• Check the charging status of the batteries. Change the
batteries when the message Batt lo is displayed upon
switch-on.
• Check that the batteries are properly positioned. Check the
polarity is correct.
• Never carry out an electrical check yourself; instead, contact
your Lufft®customer service.
PC software
Errors and faults

EN Operating manual – temperature measuring device XP100 / XP101 15
11_2014
For maintenance or repair work which requires the
housing to be opened, contact Lufft®customer
service. Devices which have been opened
unlawfully are void of any warranty and warranty
claims.
Cleaning the device
1. Use a soft, lint-free cloth for cleaning.
2. Dampen the cloth with clean water. Do not use sprays,
solvents, alcohol-based or abrasive cleaners to dampen the
cloth.
3. Remove dirt from the housing, the connections and the
display.
Battery change
Change the batteries when the message Batt lo is displayed upon
switch-on or the device can no longer be switched on. See
Inserting the batteries on page 5.
An overview of the currently available PT100 sensors is provided
below.
Further details about PT100 sensors and their use is provided in
the separate general catalogue.
Note!
Lufft®continually improves and broadens the range of available
sensors. Information on additional, new sensors can be found on
the website www.lufft.de.
Maintenance Available PT100 sensors
PT100 sensor Article num-
ber
Compatible
with
XP100 XP101
Immersion probe, short 3120.520 X X
Immersion probe, long 3120.530 X X
Immersion/penetration probe, long 3120.540 X X
Stainless steel food penetration probe 3120.550 X X
Immersion probe for XP100 3120.560 X
Surface probe 3120.600 X X
Precision ceramic probe for XP101 3120.700 X
3120.
540 3120. 700
3120.
520 3120. 530
3120.
600

16 Operating manual – temperature measuring device XP100 / XP101 EN
11_2014
Connecting third-party sensors
When connecting third-party sensors to the device, only use the
original plug-in connector (article number: 3120.50). The
maximally permissible connection cross-section is 0.75 mm².
Please observe the following connection diagram:
Note!
Sensors must be connected using the 4-wire technique, the
3-wire technique is not supported.
In the European Union, electronic equipment must not
be treated as domestic waste, but must be disposed of
professionally in accordance with Directive
2002/96/EC of the European Parliament and Council of 27th
January 2003 concerning old electrical and electronic equipment.
After the end of its use, please dispose of this device in a manner
appropriate to the relevant legal requirements.
In the European Union, batteries must not be treated as domestic
waste, but must be disposed of professionally in accordance with
Directive 2006/66/EC of the European Parliament and Council of
6th September 2006 concerning batteries and accumulators.
Please dispose of batteries in a manner appropriate to the
relevant legal requirements.
in accordance with the EC Low Voltage Directive 2006/95/EC and
the EC Directive 2004/108/EC about electromagnetic
compatibility.
Herewith, we declare that the temperature measuring device
XP100 / XP101 was developed, constructed and produced in
compliance with the named EC directives.
Applied harmonised standards:
EN 61326-1:2013
The marking is found on the rear of the device.
Manufacturer:
G. Lufft Mess- und Regeltechnik GmbH
Gutenbergstr. 20
D-70736 Fellbach
Phone: [phone]
Fax: [phone]
Email: inf[email protected]
Fellbach, 31/08/2014
Managing Director: Axel Schmitz-Hübsch
No. Designation
Pin 1 Force High (+)
Pin 2 Sense High (+)
Pin 3 Sense Low (-)
Pin 4 Force Low (-)
Disposal
Declaration of conformity

a passion for precision · passion pour la précision · pasión por la precisión · passione per la precisione · a passion for precision · passion pour la précision · pasión por la precisión · passione per la precisione · a passion for precision · passion pour la précision · pasión por la precisión · passione per la precisione ·
G. LUFFT Mess- und
Regeltechnik GmbH
Lufft Germany:
Fellbach Office:
Postal Address:
Gutenbergstrasse 20
D-70736 Fellbach
Address:
P.O. Box 4252
D-70719 Fellbach
Tel.: [phone] - 0
Fax: [phone] - 41
www.lufft.com
[email protected]
Berlin Office:
Oderstr. 59
D-14513 Teltow
Tel.: [phone]
Fax: [phone]
Lufft North America:
Lufft USA, Inc.
820 E Mason St #A
Santa Barbara, CA 93103
Tel.: [phone]
Fax: [phone]
E-Mail: [email protected]
www.lufft.com
Lufft China:
Shanghai Office:
Lufft (Shanghai)
Measurement & Control
Technology Co., Ltd.
Room 507 & 509, Building No.3,
Shanghai Yinshi Science and
Business Park,
No. 2568 Gudai Road,
Minhang District,
201199 Shanghai, CHINA
Tel: [phone]
Fax: [phone]
E-Mail: [email protected]
www.lufft.cn
Beijing Office:
B501 Jiatai International Mansion
No. 41 East 4th Ring Road,
Chaoyang District,
100025 Beijing, CHINA
Tel: [phone]
Fax: [phone]
E-Mail: [email protected]
Technische Änderungen vorbehalten 10 08_2014