4
The automatic squelch (ASQ ) uses a preset average value. It can be
activated by short key (C) [ ASQ ],The automatic squelch mode
(AQ icon) is indicated on the LCD.
Channel selection
4.
Modulation MODE selection
5.
This key (6) [AM/FM] allows selecting the AM or FM modulation. Your
modulation mode has to correspond to the one of your correspondent.
With the version Full Multi Norm in the norm UK, you can switch
between the EU.band and the UK band, which is indicated by symbol
"EU" or "UK", by pressing the key (6) [AM/FM ].
The CB band EU consists of the 40 CEPT channels. The CB band UK
consists of 40 channels starting from 27.60125 MHz to 27.99125 MHz.
Norm Selection
6.
The version Full Multi Norm can be set by the user to the following
norms:
All channels can be selected by channel selector keys (8) [ ] or (9)
[ ].The selected channel is displayed on the LCD. In
communication both transceivers (the receiving and transmitting party)
need to be in the same channel and under same modulation type.
Turn the SQ knob(2) clockwise to the exact point where all background
noise disappears. 3OHDVHQRWHWKDWWKLVFRQWUROLV¿QHUHJXODWLRQLI\RX
set this SQ control to the maximum (fully clockwise), the radio can
only receive the strongest signal.
Automatic Squelch
3.
Manual Squelch
2.
D 80 FM (26.565 - 27.405 MHz), 4 W
40 AM (26.965 - 27.405 MHz), 1W.
EU 40 FM (26.965 - 27.405 MHz), 4 W
40 AM (26.965 - 27.405 MHz), 1W.
EC 40 FM (26.965 - 27.405 MHz), 4 W.
UK 40 FM (27.60125 - 27.99125 MHz), 4 W
40 FM (26.965 - 27.405 MHz), 4W.
PL 40 FM (26.960 - 27.400 MHz), 4 W
40 AM (26.960 - 27.400 MHz), 4W.
E 40 FM (26.965 - 27.405 MHz), 4 W
40 AM (26.965 - 27.405 MHz), 4W.
US 40 AM (26.965 - 27.405 MHz), 4W.
NZ 40 FM (26.330 - 26.770 MHz), 4 W
40 AM (26.330 - 26.770 MHz), 4W.
To change current norm, please hold the key (6) [AM/FM ] while
turning the radio on. In the display, the symbol of the current norm
appears, please select the norm by pressing the channel selector
key(8) [ ] or (9) [ ]. To verify your selection, turn the
radio off and on again, the radio automatically returns to the selected
operation mode.
Note:
The norm is internally set to 40 channels FM, 4 Watts only.
HOW TO USE YOUR CB RADIO
ON/OFF-Volume
1.
a)To turn the set on, turn the knob (1) clockwise.
b)To increase the sound level, turn the same knob further clockwise.
Automatic Scanning
7.
Press the key(10) [ SC ] to enable the SCAN function. Before enabling
the SCAN function, firstly turn the SQ control clockwise till the
background noise is cut out. Then press the key(10) [ SC ], radio will
automatically scan all channels and the SC icon will appear on the
LCD.
When a signal is detected on a channel, scanning stops on this
channel. You can receive the calling, and also, can transmit on this
channel by pressing PTT key. If there is no transmission or detected
signal on that channel within 5 seconds, radio will start scanning
5
again. To exit the SCAN function, press the SC Key or the PTT key.
Priority Channel 9 / 19
8.
-It the contains the priority channels 9 and 19. Priority channel 9
is selected by pressing the key (7) [ CH9/19 ] once. To set priority
channel 19, press the key(7) [ CH9/19 ] twice.
Transmitting
9.
To transmit, press and hold the key(A) [ PTT ] at the microphone and
the TX icon will appear on the LCD.
For best quality, please speak normally at a distance of 2 - 4 inches.
6SHDNLQJWRRORXGO\ZLOOFDXVHGLVWRUWLRQVDQGPDNHWKHVLJQDOGLI¿FXOW
to understand.
On completion of the transmission release the PTT key and the radio
will revert to receiving mode.
External speaker jack
10.
The radio is equipped with a 3.5 mm jack socket(D) at the rear panel
to connect an external.speaker of 4 - 8 ohm impedance. At 4 ohms the
speaker load can be 4 watts. When the external speaker is connected,
the internal speaker will be switched off.
12.RF GAIN
RF gain is reduced, it can be short press (5) to achieve
13.Microphone
KEY (A) is {PTT},KEY (B) is {DOWN},KEY(C) is {AQ}, KEY(D) is {UP}
