Lukas AMIN 19-100 GHL User manual

- AMIN 19-100 GHL -Stand: 18.09.2007
Bedienungsanleitung
Operation Instructions
AMIN 19-100 GHL

- AMIN 19-100 GHL -Stand: 18.09.2007
1
2
3
4
5
6
7
8
Appendix
A
B
C
D
Introduction
Technical data
Commissionin
g
Usa
g
e
Safet
y
Instructions
Maintenance Instructions
Warrant
y
Spare Part List
Technical Drawings
Service and Manufacturer's Address
Declaration of Conformit
y
Warrant
y
Certificate
13
13
14
15
16
17
17
18
21
26
27
28
Index
12

13 - AMIN 19-100 GHL -Stand: 18.09.2007
1. Introduction
The AMIN 19-100 GHL is a pneumatic power tool reflecting state-of-the-art
technology.
It is driven by a vane air motor using compressed air.
The integral speed controller keeps the rotation at a constant speed.
With this power tool both tungsten carbide burrs and mounted points can be used
economically.
The vibration and sound values specified in the technical data were measured
according to EN 28662-1 and EN ISO 8662-13 as well as prEN ISO 15744.
Prior to using the power tool you should become familiar with
the operation instructions.
The power tool must not be commissioned before the safety
information for the operator has been read.
2. Technical Data
Type: straight die grinder with lever valve
max. RPM: 19.000 min-1 - 10%
Service pressure: 0,63 MPa
Nomials hose diameter: 12 mm
Weight: approx.. 2,2 kg
Dimensions: ca. ∅52 x 310 mm
Output: 1,0 KW
Air Consumption: approx. 0,8 m³/min.
Noise levell: 84 dB(A) max.

14 - AMIN 19-100 GHL -Stand: 18.09.2007
Vibration acelleration: < 2,5 m/s2
Drive: Vane Air Motor
Accessories included:
- 1 collet Ø 6mm
- 2 spanners SW19 and SW22
Optional Equipment:
- collets Ø 8mm; 8mm; 3/16"; 5/16“; 1/4"
3. Commissioning
The power tool must only be connected to the compressed air network using a
pressure reducer (combination of water separator – pressure control valve –
lubricator). The nominal diameter of the pressure reducer must comply at least with
the hose diameter specified in the technical data. The pressure control valve must be
set to the value of 0.63 MPa.
The pressure reducer must be installed at the working height of the power tool or
above.
The compressed air hose supplied with the machine must be directly connected to
the pressure reducer and must not be lengthened.
The lubricator must be adjusted so as to supply approx. 3 drips per minute at a
pressure of 0,63 MPa. Only oil types quoted in the table below may be used.
In the case of a prolonged period without use (e.g. overnight), the machine must be
disconnected from the compressed air system.

15 - AMIN 19-100 GHL -Stand: 18.09.2007
Suitable oil types Viscosity
Festo Spezialöl
Aral Vitam GF 22
Esso Nuto H 22
Mobil DTE 22
BP Energol HLP 22
Shell Tellus C 22
22 mm²/s(=cSt) bei 40°C
ISO-Klasse VG 22
nach ISO 3448
4. Usage
Only tools may be used which are suitable for the power tool and which have a shaft
diameter that is correct for the collet. The use of cutting discs as well as groove and
profile milling cutters is prohibited.
Only use tools with a permissible operating speed of at least the maximum speed of
the power tool.
When using mounted points, the largest recommended distance L0between the
collet and the rear side of the abrasive wheel is 10 mm (see illustration). When this
distance is greater, the permissible speed is reduced. The burr manufacturer's
recommendations must be adhered to. A minimum clamping length of 10 mm must
be observed, independent of the type of tool used.
Always ensure that the main load is transmitted in a radial direction (i.e. on the tool
circumference) and not in an axial direction to the power tool.
The tool in use must be firmly clamped into the collet using the two flat spanners
supplied.
Before changing a tool or undoing the compressed air hose, the power tool must be