Lumag STM350-800 User manual

Distribution Limited
Electric Masonry Saw Bench
Operator’s Manual
STM350-800
FOR YOUR SAFETY
READ AND UNDERSTAND THE ENTIRE MANUAL
BEFORE OPERATING THIS MACHINE

STM350_800_GB_.doc
1
Stone cutting machine
For your Safety Read Instruction Manual Before Operation Saw.
Wear eye protection
Use cut-blade guard and spreader for every operation for which it can be used including all through
cutting.
Keep hands out of line of cut blade.
Use a push-stick when required
Pay particular attention to instruction on reducing risk of kickback.(or” know to reduce risk of
kickback”)
Do not perform any operation freehand.
Applications
Cutting various types of stones.
Cutting various types of tiles used on wall, ground and roof.
General Operational Precautions
Know your Power tools. Read the other’s manual carefully learn the tools applications and limitations
as well as the specific potential hazards peculiar to it.
Keep work area clean. Clutter areas and benches invite injuries.
Consider work area environment. Don’t expose power tools to rain. Don’t use power tools in damp or
wet locations. Keep work area well lit. Don’t use tools in presence of flammable liquids or gases.
Guard against electric shock, prevent body contact with grounded surfaces. For example pipes,
radiators enclosures.
Keep children and visitors away.
Don’t force tool. It will work efficiently and safely under its designed work condition.
Use right tool. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool
for purpose not intended.
Wear proper apparel. No pose clothing, gloves, necktie, or jewel to get caught in moving parts.
Rubber gloves and non-skid footwear are recommended when working outdoors, wear protective
hair covering to contain long hair.
Use safety glasses. Also use face or dust mask if cutting operation is dusty.
Secure work .Use clamps or a vise to hold work piece. When practical. It’s safer than using your
hands and free both hands to operate tools.
Maintain tools with care. Keep tools sharp and clean for hest and safety performance. Follow
Instructions for lubricating and changing accessories.
Disconnect tools. Before servicing and when changing accessories, such as blades, bits, cutters.
Avoid starting. Make sure switch is in “OFF” position before plugging in cord.
Check damaged parts. Before further use of the tool, a guard or other part that is damaged should
be carefully checked to ensures that it will operate properly and perform its intended function-check
for alignment of moving parts, binding of moving parts, break age of parts, mounting, and any other
conditions that may affect its operation .A guard or other part that is damaged should be properly
repaired or replaced.
Don’t touch moveable parts or accessories unless the power source has been disconnected.
Use your tool at lower input than specified on the nameplate, otherwise, the accuracy may be
spoiled and working efficiency reduced due to motor overload.
Don’t wipe plastic parts with solvent. Solvent such as gasoline, thinner, carbon and oil containing

STM350_800_GB_.doc
2
chlorine annex may damage and crack plastic parts. Do not wipe them with such solvent. Wipe
plastic parts with soft cloth lightly dampened with soapy water.
Consult an authorized service agent in the event of power tool failure.
Precaution on Using Cutter.
Don’t use any cutting tool other than a diamond wheel.
Don’t use it four cutting of materials or curve cutting. For doing so, diamond wheel may be broken or
its service life may be remarkable reduce.
Be sure to taken an earth leakage circuit breaker or isolating transformer as electric
shock-preventive measures.
Wear protective glasses, gloves to protect yourself.
Prior to use, be sure to check the diamond wheel in such detail as crack, broken part, bent part and
the like. Don’t use a diamond wheel if any of the above defect is found with the wheel. Also confirm
that no abnormality exists by actual test running.
Proceed with cutting operation when full speed has been reached.
Never touch diamond wheel while operating.
While cutting, the guards should not be disassembled to secure work safety and stable.
Should the diamond wheel stop or make an abnormal noise while operating, promptly cut OFF the
switch.
Tools Required for Assembly.
Put the workplace on the portable-table and rest against the slide rack closely. The cutting it.
Maintenance
Inspecting the diamond wheel: since use of dull diamond wheel cause motor manufacture and
degraded efficiently replace with a new one without delay when abrasion is noted.
Inspecting the mounting screws: regularly inspect all mounting screws and ensure that they are
properly tight. Should any of the screws loose, retighten them immediately. Failure to do so could
result in serious hazard.
Maintenance of the motor: the motor unit winding is the most important part of this power tool. Check
it carefully to ensure the winding does not become damaged and/or wet with oil or water. Clean the
whole set regularly.