Lumapower EDC LM 33 User manual

EDC LM 33 (XM-L U2 upgrade)
User Manual

Welcome to Lumapower
Please take a moment to register your product on our Web site at
http://www.Lumapower.com. It enables us to keep you posted on our latest advancements,
and helps us to better understand our customers and build products that meet their needs
and Expectations.
This product has been designed and manufactured to the highest quality standards. However,
if something does go wrong with this product, Lumapower and its national distributors
warrant free of charge labour and replacement parts in any country served by an official
distributor.
Unpacking: Check the product carefully. If it has been damaged in transit, report the
damage immediately by calling your dealer and/or the shipping company that delivered it.
Read Instructions. All the safety and operating instructions should be read before the
product is operated.
Follow Instructions. All operating and use instructions should be followed.
Replacement Parts. When replacement parts are required, be sure the replacement parts
have the same characteristics as the original part. Unauthorized substitutions may cause
damage to the unit.
Introduction
Lumapower EDC LM 33 supports input voltage from 0.9V to 4.2V. It is powered by 1 x CR123A,
1 x 16340 batteries. EDC LM 33 is fitted with pure white LED module driven by current
regulation circuitry to achieve a consistent level of light output for the useable life of the
batteries.

EDC LM 33 features a forward clicky switch and multi-level digital output control circuit.
Half-press the tail switch to power on EDC LM 33 momentary, and full press to lock it for
constant on.
Digital output control
Half press to cycle the output from Low, Medium and High.
At each output level, with a full press to lock it.
You can change the output by power off and on.
The power off status over 5 seconds will restore the output status to low output with your
next start.
Battery Installation
Unscrew the Head housing and insert new battery with positive ends towards LED assembly.
Replace bezel and hand tighten. Depress tailcap pushbutton switch to test.
Note: It would not light if battery is inserted in wrong direction.
Mechanical polarity protection will protect the circuit from wrong battery insertion.
CAUTION: EDC LM 33 flashlights are high-output lighting devices. Due to possible
eye injury, DO NOT look directly into the reflector when the light is switched on.
Safety is your responsibility, too.
External surface temperature will rise during prolonged operation; this is a normal operating
phenomenon.
Battery Replacement
If there is significant decrease in brightness of light output you should replace the battery.
Unscrew the Head housing and remove the old battery. Insert a new battery as mentioned in
Battery Installation Guide
WARNING: Lithium batteries can explode or cause burns if disassembled, shorted,
recharged, exposed to water, fire, or high temperatures. Do not place loose batteries in a
pocket, purse or other container containing metal objects or store with hazardous or
combustible materials. Store in cool, dry, ventilated area. Follow applicable laws and
regulations for disposal.
Maintenance
Clean and lubricate threads with a clean cloth and apply thin coat of silicon-based lubricant to
rubber O-rings. Note: Do not use petroleum-based lubrication on O-rings. After prolonged
exposure to moisture, the bezel and batteries should be removed, inspected, and dried if
necessary.

WARNING: Lumapower reflector is made with high precision process. Do not touch
or clean the reflecting surface using any cloth which may cause damage to the surface
material affecting the illuminating performance.
Non-use Periods.
If EDC LM 33 is left unused for long period, the installed battery should be removed from the
unit.
Output & Runtime
Accurately specifying light output (lumens) and runtime is complicated for LED flashlights.
Installed batteries and operating temperature are the main factors affecting the light output
and runtime. Lumapower doesn’t guarantee its products can reach the specification under the
using condition of users.
Specification
LED : Cree XM-L U2
Reflector : OP textured type, (Optional SMO)
Max. OTF Lumens : 5, 120, 240 (primary CR123A); 10, 250, 430
(rechargeable Li-ion 16340)
Runtime (minutes) : 55 (High), 200 (Medium), 6000 (Low) : CR123A
Batteries : 3.0V primary CR123A, 3.7V rechargeable Li-ion (16340)
Length : 82mm
Bezel/Tail Diameter : 22mm / 21.5mm
Body Diameter : 20mm
Weight : 36.5g (without battery installed)
Material : T6061 aircraft aluminum
Body coating : Type III HA Grey
Accessories : spare o-rings, lanyard.
Battery is not included.
Specifications: All product specifications/features are subject to change without notification.
Reflecting surface