Lumens LC-RC01 User manual

To download the latest version of Quick Start
Guide, multilingual user manual, software, or
driver, etc., please visit Lumens
https://www.MyLumens.com/support
LC-RC01
Remote control panel
(Remote Control Panel)
User Manual - English
[Important]

English-1
Table of Contents
Chapter 1 Package Contents.................................................................................................2
Chapter 2 Product Overview..................................................................................................3
2.1 LC-RC01 adapter...........................................................................................................3
2.2 LC-RC01 control box....................................................................................................3
2.3 Size.................................................................................................................................4
Chapter 3 Instruction for installation....................................................................................5
3.1 Secure the adapter to the media processor with screws and connect the DC power
and USB.........................................................................................................................5
3.2 Use the CAT5e network cable for connection (the length shall not exceed 30
meters)...........................................................................................................................5
3.3 Pass a cable tie through the mounting hole to secure the network cable onto the
LC-RC01 control box....................................................................................................6
3.4 Install the control box on the wall...............................................................................6
Chapter 4 Function Description ............................................................................................7
4.1 Button function description.........................................................................................7
4.2 LED Indicator Description............................................................................................7
4.3 Web Page Function.......................................................................................................8
Chapter 5 Troubleshooting....................................................................................................9
Chapter 6 Safety Instructions..............................................................................................10
Copyright Information .............................................................................................................11

English-2
Chapter 1 Package Contents
LC-RC01
Power Adapter
(Appearance may vary
depending on country/ region)
M3 x4 Flat Head(x2)
Quick Installation Guide

English-3
Chapter 2 Product Overview
2.1 LC-RC01 adapter
2.2 LC-RC01 control box
NO.
Item
Function Descriptions
5.
USB 2.0 port
The USB flash disk can be inserted for backup
6.
Function buttons
Please refer to 4.1 Button function
description
7.
RJ-45 port
Connecting to RJ45 network port of the
adapter
NO.
Item
Function Descriptions
1.
DC Power output
connector
Connecting to the recording system
2.
USB control
connector
Connecting to the USB port on recording
system
<Remark> LC200 needs to connect to the USB port
“below”
3.
DC power input
interface
Connecting the power cord originally
connected to the recording system to this
power input port
4.
RJ-45 network port
Connecting to RJ45 network port of the control
box
Front View
Bottom

English-4
2.3 Size
LC-RC01E
EU Regulations
LC-RC01U
North America
Regulations

English-5
Chapter 3 Instruction for installation
3.1 Secure the adapter to the media processor with screws and connect the DC power
and USB.
LC100 / LC100N
LC200
3.2 Use the CAT5e network cable for connection
(the length shall not exceed 30 meters)
CAT5e
Network Cable

English-6
3.3 Pass a cable tie through the mounting hole to secure the network cable onto the LC-RC01
control box.
3.4 Install the control box on the wall
Cable tie

English-7
Chapter 4 Function Description
4.1 Button function description
4.2 LED Indicator Description
Button
Indicator
Status description
1 / 2 / 3
N
The device is not in Macro mode
Blue light
The device is in Macro mode
BACKUP
N
The USB flash disk is not detected by the
recording system
Blue light
The USB flash disk is detected by the
recording system
Blue light flickering
The device is backing up the data onto the
USB flash disk
Press again to cancel back up
Red light flickering
6 times
Error in writing the data into the USB flash
disk
STREAM
N
Unpowered
Blue light
Powered, but Push is not enabled
Press again to enable Push
Red light
Pushing; press again to stop Push
Record
N
Unpowered
Blue light
Powered, but the record is not enabled
Press again to enable the record
Red light
Recording; press again to stop record
Red light flickering
6 times
Error or failure during recording
<Remark> All indicators turn into flickering blue light: LC-RC01 is not connected to the recording system.
Please check the connection of the recording system.
1 / 2 / 3：
Switch the Marco setting 1~3 to change the scene and
camera preset position. Please refer to 4.3.2 Macro
Settings for relevant settings.
RECORD：Press the button once to begin recording;
press the button again
to stop recording
BACKUP：Press the button once to start the backup;
press the button again to stop the backup (back up
the last video directory to the
USB flash disk)
USB 2.0 Port: Is available for inserting the USB flash
disk
STREAM：Press the button once to begin streaming;
press the button again to stop streaming

English-8
4.3 Web Page Function
4.3.1 Remote control panel connection
Log in to the web page, Click [System] > [Remote Control Panel] to check the connection
status between the recording system and LC-RC01
Connected
Disconnected
4.3.2 Macro Settings
Log in to the web page, Click [Scenes] > [Macro]
LC-RC01 [1~3] buttons correspond to Macro [1~3] Settings
NO.
Function Descriptions
1
Select a scene to be set. Each supports up to 9 sets of scene.
<Remark> If the layout of the scene needs to be change, please refer to
the user manual of recording system
2
Set/Cancel [Camera Preset Position]. Each supports up to 9
sets of camera preset position selection.
2
1
3

English-9
Chapter 5 Troubleshooting
This chapter describes problems you may encounter while using LC-RC01. If you have
questions, please refer to related chapters and follow all the suggested solutions. If the problem
still occurred, please contact your distributor or the service center.
NO.
Problems
Solutions
1
After installation, LC-RC01 is not
detected by the recording system
Please refer to Chapter 3 Instruction for
installation to ensure that USB cable is inserted
into the “below” USB port of LC200
2
No indicator is shown on the
LC-RC01 panel
Please refer to Chapter 3 Instruction for
installation to ensure that the control box
properly connects to the adapter by the CAT5e
network cable

English-10
Chapter 6 Safety Instructions
Always follow these safety instructions when setting up and using the LC-RC01 Remote Control Panel:
1 Operation
1.1 Please use the product in the recommended operating environment, away from water or source of heat
1.2 Do not place the product on a tilted or unstable trolley, stand or table.
1.3 Please clean the dust on the power plug prior to usage. Do not insert the product’s power plug into a
multiplug to prevent sparks or a fire.
1.4 Do not block the slots and openings in the case of the product. They provide ventilation and prevent the
product from overheating.
1.5 Do not open or remove covers, otherwise it may expose you to dangerous voltages and other hazards.
Refer all servicing to licensed service personnel.
1.6 Unplug the product from the wall outlet and refer servicing to licensed service personnel when the following
situations happen:
If the power cords are damaged or frayed.
If liquid is spilled into the product or the product has been exposed to rain or water.
2 Installation
2.1 For security considerations, please make sure the standard mount you use is in line with UL or CE safety
approbations and installed by technician personnel approved by agents.
3 Storage
3.1 Do not place the product where the cord can be stepped on as this may result in fraying or damage to the
lead or the plug.
3.2 Unplug this product during thunderstorms or if it is not going to be used for an extended period.
3.3 Do not place this product or accessories on top of vibrating equipment or heated objects.
4 Cleaning
4.1 Disconnect all the cables prior to cleaning and wipe the surface with a dry cloth. Do not use alcohol or
volatile solvents for cleaning.
5 Batteries (for products or accessories with batteries)
5.1 When replacing batteries, please only use similar or the same type of batteries
5.2 When disposing of batteries or products, please adhere to the relevant instructions in your country or region
for disposing of batteries or products
Precautions
This symbol indicates that this equipment may
contain dangerous voltage which could cause
electric shock. Do not remove the cover (or
back). No user-serviceable parts inside. Refer
servicing to licensed service personnel.
This symbol indicates that there are
important operating and
maintenance instructions in this
User Manual with this unit.
FCC 警告
This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
Notice :
The changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment..
本設備符合 FCC 規則第 15 部分的規定，本設備已經過測試，符合 A類設備的限制。這些限制旨在為在商業環境
操作設備提供合理的保護，以防止有害干擾。
IC Warning
This digital apparatus does not exceed the Class Alimits for radio noise emissions
from digital apparatus as set out in the interference-causing equipment standard
entitled "Digital Apparatus," ICES-003 of Industry Canada.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de
Classe A prescrites dans la norme sur le material brouilleur: "Appareils Numeriques," NMB-003 edictee par
l'Industrie.
EN55032 CE Warning
Operation of this equipment in a residential environment could cause radio interference.
Warning: Operation of this equipment in a residential environment may cause radio interference

English-11
Copyright Information
Copyrights © Lumens Digital Optics Inc. All rights reserved.
Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc.
Copying, reproducing or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics
Inc. unless copying this file is for the purpose of backup after purchasing this product.
In order to keep improving the product, the information in this file is subject to change without prior notice.
To fully explain or describe how this product should be used, this manual may refer to names of other products or
companies without any intention of infringement.
Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological,
editorial errors or omissions, nor responsible for any incidental or related damages arising from providing this file,
using, or operating this product.