Lumex Patriot LX US5000 User manual

US5000-INS-LAB-RevA14
© 2014 GF Health Products, Inc.
Read this manual before operating your Patriot LX Homecare Bed.
Save this manual for future use.
The most current version of this manual can be found online at
www.grahameld.com.
US5000 SEMI-ELECTRIC AND
US6000 FULL ELECTRIC
HOMECARE BED
USER MANUAL

GF Health Products, Inc. is not responsible for typographical errors. For the most updated and current information on
packaging, warranties, products and specications, including the most current version of these instructions, please visit
our website at www.grahameld.com. Graham-Field and Lumex are registered trademarks of GF Health Products, Inc.
CONTENTS
1 INTRODUCTION.................................................................................................................................................................................. 3
INTENDEDUSE........................................................................................................................................................................... 3
2 IMPORTANTSAFETYINSTRUCTIONS............................................................................................................................................. 4
DANGER/WARNING/CAUTION/NOTICESUMMARY........................................................................................................... 4
3 HANDLINGPROCEDURES................................................................................................................................................................ 7
SHIPPINGANDTRANSPORTATIONINSTRUCTIONS.............................................................................................................. 7
4 ASSEMBLYINSTRUCTIONS.............................................................................................................................................................. 8
ASSEMBLYINSTRUCTIONS:US5000SEMI-ELECTRIC.............................................................................................................. 8
US5000SEMI-ELECTRIC:MANUALHI/LODRIVERODATTACHMENTTOFOOTSECTIONANDHEADSECTION......... 8
US5000SEMI-ELECTRIC:HEADSECTIONTOFOOTSECTIONASSEMBLY...................................................................... 10
US5000SEMI-ELECTRIC:HEADSECTIONTOFOOTSECTIONRODCONNECTION..........................................................11
US5000SEMI-ELECTRIC:FOOT/HEADMOTORINSTALLATION........................................................................................ 12
ASSEMBLYINSTRUCTIONS:US6000FULLELECTRIC............................................................................................................ 14
US6000FULLELECTRIC:HI/LOMOTORASSEMBLY,HEADSECTIONANDFOOTSECTION........................................ 14
US6000FULLELECTRIC:HEADSECTIONTOFOOTSECTIONASSEMBLY...................................................................... 16
US6000FULLELECTRIC:FOOT/HEADMOTORINSTALLATION....................................................................................... 17
US6000FULLELECTRIC:HI/LOMOTORCORDROUTING................................................................................................. 19
ASSEMBLYINSTRUCTIONS:US5000/US6000......................................................................................................................... 20
US5000/US6000:POWERCORDROUTINGANDATTACHMENTTOMAINFRAMERAIL................................................. 20
US5000/US6000:RECOMMENDEDPENDANTHANDCONTROLCABLEROUTINGANDTIE-OFF................................. 21
US5000/US6000:HEADBOARDPANELMOUNTASSEMBLYANDINSTALLATION.......................................................... 22
US5000/US6000:FOOTBOARDPANELMOUNTASSEMBLYANDINSTALLATION........................................................... 23
US5000/US6000:OPTIONALCASTERMOUNTASSEMBLY................................................................................................ 24
5 OPERATIONINSTRUCTIONS.......................................................................................................................................................... 25
OPERATIONINSTRUCTIONS:US5000SEMI-ELECTRIC.......................................................................................................... 25
US5000HI/LOHANDCRANKOPERATION(RAISEANDLOWERENTIREBED)............................................................... 25
US5000SEMI-ELECTRIC:PENDANTHANDCONTROLOPERATION.................................................................................. 26
POWERFAILURE...................................................................................................................................................................... 26
OPERATIONINSTRUCTIONS:US6000FULLELECTRIC.......................................................................................................... 27
US6000FULLELECTRIC:PENDANTHANDCONTROLOPERATION.................................................................................. 27
POWERFAILURE...................................................................................................................................................................... 27
BEDPOSITIONING:US5000/US6000........................................................................................................................................ 28
6 COMPONENTS,OPTIONSANDACCESSORIES............................................................................................................................ 29
COMPONENTS(PATRIOTLXASSHIPPED)............................................................................................................................... 29
COMPONENTS(PATRIOTLXASSHIPPED):US5000SEMI-ELECTRICBED....................................................................... 29
COMPONENTS(PATRIOTLXASSHIPPED):US6000FULLELECTRICBED...................................................................... 29
SERVICECOMPONENTS............................................................................................................................................................. 29
SERVICECOMPONENTS:US5000/US6000.......................................................................................................................... 29
SERVICECOMPONENTS:US5000SEMI-ELECTRICBED..................................................................................................... 29
SERVICECOMPONENTS:US6000FULLELECTRICBED..................................................................................................... 29
OPTIONS........................................................................................................................................................................................ 30
OPTIONS:US5000/US6000..................................................................................................................................................... 30
OPTIONS:US5000SEMI-ELECTRICBED............................................................................................................................... 30
OPTIONS:US6000FULLELECTRICBED............................................................................................................................... 30
ACCESSORIES:US5000/US6000.............................................................................................................................................. 30
PATRIOTLXACCESSORIES:BEDRAILS............................................................................................................................... 31
PATRIOTLIBERTYBEDRAILS................................................................................................................................................ 32
LUMEXUNIVERSALBEDRAIL................................................................................................................................................ 34
7 CAREANDMAINTENANCE............................................................................................................................................................. 35
SAFETYCHECKS/MECHANICALCHECKS/LUBRICATION............................................................................................... 35
CLEANING................................................................................................................................................................................. 35
8 TROUBLESHOOTING....................................................................................................................................................................... 36
9 SPECIFICATIONS............................................................................................................................................................................. 37
MECHANICALSPECIFICATIONS............................................................................................................................................. 37
ELECTRICALSPECIFICATIONS.............................................................................................................................................. 37
10 LIMITEDWARRANTY....................................................................................................................................................................... 38
11 INDEX................................................................................................................................................................................................ 39
US5000-INS-LAB-RevA14 2

1 INTRODUCTION
INTENDED USE
The intended use of the Patriot LX Homecare Bed is sleeping and resting in a homecare setting.
The bed may be used for alleviation of or compensation for an injury, disability or illness, and for
easing the working condition of the caregiver. This bed is suitable for adult patients; this bed is not
suitable for children. Only the patient’s health professional can determine the suitability of this
homecare bed.
Contraindications
WARNING: Use this device only as intended and described in this manual. Do not use
attachments or accessories not recommended by GF Health Products, Inc.
WARNING: This bed is not intended for use by children.
WARNING: Under normal operating conditions, this product has a maximum working
load / maximum total weight capacity of 450 lb (204 kg), EVENLY DISTRIBUTED,
including patient, mattress, accessories, rails, etc.
This product has a maximum patient weight capacity of 350 lb (158 kg), EVENLY
DISTRIBUTED.
WARNING: DO NOT use this product in the presence of ammable anesthesia.
There is a possible re hazard when this product is used with certain oxygen delivery
equipment. Use ONLY nasal cannula or face mask to deliver oxygen in the presence of
this product.
US5000-INS-LAB-RevA14 3

2 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT: Before using the Patriot LX Homecare Bed, please read and adhere to
the following safety precautions and warnings. Failure to do so could result in serious
personal injury or damage to the Patriot LX Homecare Bed.
Always consult your healthcare professional to determine safe methods most suitable for your
individual abilities. Protect yourself, your attendant, and the Patriot LX Homecare Bed by having
it serviced regularly. If you experience any malfunction, contact your Graham-Field authorized
distributor immediately, as a hazardous condition could result, causing personal injury or damage
to your Patriot LX Homecare Bed.
Periodic inspection, adjustment and replacement of worn parts are necessary to provide years of
excellent service. Refer to CARE AND MAINTENANCE section of this manual.
Maintenance MUST be performed by qualied personnel ONLY.
SAVE THESE INSTRUCTIONS.
Signicance of safety statements
Please note the following special statements, used throughout this manual, and their signicance:
DANGER: Indicates a potential hazard situation or unsafe practice that, if not avoided,
will result in death or serious personal injury.
WARNING: Indicates a potential hazard situation or unsafe practice that, if not
avoided, could result in death or serious personal injury.
CAUTION: Indicates a potential hazard situation or unsafe practice that, if not
avoided, could result in minor or moderate personal injury.
s NOTICE: Indicates a potential hazard situation or unsafe practice that, if not avoided,
could result in product or property damage.
Info: Provides application recommendations or other useful information to ensure that you
get the most from your product.
DANGER / WARNING / CAUTION / NOTICE SUMMARY
DANGER: To Reduce the Risk of Electric Shock:
DANGER: Always unplug the bed from the electrical outlet before cleaning.
WARNING: To Reduce the Risk of Burns, Fire, Electric Shock, or Personal Injury:
WARNING: Important! Read and understand these instructions before assembling or
using the Lumex Patriot LX Homecare Bed. If you do not understand any part of these
warnings, cautions or instructions, contact a healthcare professional for direction in the
use of this product. If the Lumex Patriot LX Homecare Bed is not properly assembled,
personal injury and damage to the bed could result.
WARNING: If components are damaged or missing, contact your Graham-Field
authorized distributor immediately. DO NOT use substitute parts. Use only Lumex
replacement parts. The use of non-Lumex replacement parts could cause personal
injury, property damage, and void the warranty.
WARNING: Unauthorized modication of your Patriot LX Homecare Bed could cause
personal injury, property damage, and void the warranty.
US5000-INS-LAB-RevA14 4

WARNING: Under normal operating conditions, this product has a maximum working
load / maximum total weight capacity of 450 lb (204 kg), EVENLY DISTRIBUTED,
including patient, mattress, accessories, rails, etc.
This product has a maximum patient weight capacity of 350 lb (158 kg), EVENLY
DISTRIBUTED.
WARNING: Ensure that body weight is evenly distributed over the surface of the
bed. Do not lie, sit, or lean in such a way that your entire body weight is placed only
on the raised head or foot section of the bed. This includes when assisting the user in
repositioning or transferring in or out of bed.
WARNING: Keep hands and feet clear of all moving parts.
WARNING: Do not allow small children on or near bed during operation.
WARNING: Do not allow this device to be operated by small children.
WARNING: When operating ANY bed change of position, ALWAYS ensure that the
individual conned to the bed is positioned properly within the connes of the bed. DO
NOT let any extremities protrude over the side or between the bed rails when performing
any functions.
WARNING: Before operation, ensure that the bed frames are properly seated and
locked in place.
WARNING: Keep all moving parts free of obstruction (i.e. blankets, sheets, heating
blankets, pads, tubing, wiring, and other types of products).
WARNING: Ensure that Headboard, Footboard, and Locking Hardware installation
have been performed properly per instructions in order to prevent personal injury when
moving the bed or using a bed-mount trapeze.
WARNING: WARNING / CAUTION labels applied to the bed outline hazards or unsafe
practices that could result in personal injury and / or property damage; do not remove
them.
WARNING: When assembling the bed, ensure the power cord has been properly cable-
tied to the frame so that it cannot be pinched or caught on any part of the bed during
normal operation of the bed.
WARNING: Ensure the power cord and Hi / Lo Motor cords DO NOT get tangled around
the bed, bed rails, or legs during normal operation of the bed.
WARNING: Use this device only as intended and described in this manual. Do not use
attachments or accessories not recommended by GF Health Products, Inc.
WARNING: Never operate this product if:
a. it has a damaged cord or plug,
b. it is not working properly,
c. it has been dropped or damaged, or
d. it has been dropped into water.
If so, return the product to your Graham-Field authorized distributor for examination and
repair.
WARNING: Keep the cord away from heated surfaces.
WARNING: Do not leave the bed unattended when plugged in.
WARNING: Always unplug the bed from the electrical outlet before installing or
removing parts.
WARNING: To disconnect the bed, remove the plug from the electrical outlet.
WARNING: Do not use the Patriot LX outdoors.
US5000-INS-LAB-RevA14 5

WARNING: Check all parts for shipping damage before using. In case of damage, DO
NOT USE the equipment. Contact the carrier or your Graham-Field authorized distributor
for further instructions.
WARNING: Notice for California Customers- California Proposition 65 WARNING:
This product contains a chemical known to the State of California to cause cancer and
reproductive or developmental harm.
WARNING: GF Health Products, Inc. assumes no responsibility for any damage or
injury caused by improper assembly or use of this product.
WARNING: GF Health Products, Inc. specically disclaims responsibility for any
bodily injury or property damage which may occur during any use which does not
comply with federal, state or local laws or ordinances.
NOTICE: To Reduce the Risk of Product or Property Damage:
s NOTICE: The pendant hand control cord must be routed and secured properly to ensure
that the cord does NOT become entangled and eventually severed during use.
s NOTICE: When using nasal or masked type administering equipment, oxygen or air tubing
MUST be routed and secured properly to ensure that tubing does NOT become entangled
and eventually severed during normal operation of the Patriot LX.
US5000-INS-LAB-RevA14 6

3 HANDLING PROCEDURES
SHIPPING AND TRANSPORTATION INSTRUCTIONS
If the Patriot LX Homecare Bed is to be reshipped by common carrier, it should be packed in the
same carton in which it was received.
Unpacking
The Patriot LX is shipped in two cartons: a Head Section Carton and a Foot Section Carton. The
Head Section Carton contains the Head Section as well as a box that contains the Motor, Pendant,
Panel Mount Tubes, and Hardware. The Foot Section Carton contains the Foot Section, Headboard,
and Footboard.
1. Check for any obvious damage to the carton or its contents. If damage is evident, notify the
carrier or your Graham-Field authorized distributor.
2. Remove all loose packing from the carton.
3. Carefully remove all the components from the carton.
Info: Unless the Patriot LX Homecare Bed is to be used immediately, retain boxes, containers
and packing material for use in storing until use of Bed is required.
Inspection
1. Examine the exterior of the Patriot LX Homecare Bed for nicks, dents, scratches or other
damage.
2. Inspect all components.
Storage
1. Store the repackaged Patriot LX Homecare Bed in a dry area.
2. DO NOT place other objects on top of the repackaged bed.
US5000-INS-LAB-RevA14 7

4 ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS: US5000 SEMI-ELECTRIC
s NOTICE: Perform the steps on this page rst after removal of bed from carton. The
Manual Hi / Lo Drive Rod (Hi / Lo Rod) must rst be attached to each bed section and
secured with the Lanyard BEFORE assembling the Patriot LX sections together.
US5000 SEMI-ELECTRIC: MANUAL HI / LO DRIVE ROD ATTACHMENT TO FOOT
SECTION AND HEAD SECTION
US5000 Semi-Electric: Manual Hi / Lo Drive Rod to Foot Section Attachment
FOOT
SECTION
Closeup of Foot Hi / Lo Rod
and Lanyard Connection
Pull out Foot Section
from Carton
Lift Legs up slightly to move
Hi / Lo Rod toward Foot End
Crank
Pin
Line up holes in Hi / Lo Rod and Crank Pin
Lanyard Assembly
with Clevis Pin and
Hair Pin Clip
Hi / Lo Rod
1. Pull the Foot Section out of the packaging carton and lay it at, resting on decks, as shown at
right above.
2. Release the Hair Pin Clip from the Clevis Pin on the Lanyard near the foot end of the Hi / Lo Rod
shown in the Closeup above.
3. Lift the leg weldment up slightly until the Hi / Lo Rod slips fully onto the Crank Pin and the
small holes line up.
4. Insert the Clevis Pin through the holes and secure it with the Hair Pin Clip.
US5000-INS-LAB-RevA14 8

US5000 Semi-Electric: Manual Hi / Lo Drive Rod to Head Section Attachment
Pull out Head Section
from Carton
HEAD
SECTION
Closeup of Head Hi / Lo Rod
and Lanyard Connection
Crank
Pin
Line up holes in Hi / Lo Rod and Crank Pin
Lanyard Assembly
with Clevis Pin and
Hair Pin Clip
Hi / Lo Rod
Lift Legs up slightly to move
Hi / Lo Rod toward Head End
1. Pull the Head Section out of the packaging carton and lay it at, resting on decks, as shown
above.
2. Release the Hair Pin Clip from the Clevis Pin on the Lanyard situated near the head end of the
Hi / Lo Rod.
3. Lift the leg weldment up slightly until the Hi / Lo Rod slips fully onto the Crank Pin and the
small holes line up.
4. Insert the Clevis Pin through the holes and secure it with the Hair Pin Clip.
US5000-INS-LAB-RevA14 9

US5000 SEMI-ELECTRIC: HEAD SECTION TO FOOT SECTION ASSEMBLY
Slot Pin
Slot Pin
Motor Cams
FOOT
SECTION
HEAD
SECTION
1. Place the Head and Foot Sections on their sides at approximately right angles to each other
with Motor Cams up, as shown above.
2. Slide the Head and Foot Sections together until the Head Section’s Pins seat into the Foot
Section’s Slots on both sides. Ensure the Pins are completely seated before continuing.
Head
Wing
Straighten
FOOT
HEAD
3. With the Pins fully seated in the Slots as described in step 2, rotate and straighten the bed as
shown above. Position Head Wing as shown above.
US5000-INS-LAB-RevA14 10

Sliding Coupler on
Foot
Section Rod
Head Section Rod
A
US5000 SEMI-ELECTRIC: HEAD SECTION TO FOOT SECTION ROD CONNECTION
Sliding Foot Section Coupler onto Head Section Rod
1. Ensure the Head and Foot Sections have been properly assembled as described.
2. Once the Head Section Pins have been properly seated into the Foot Section Slots and the
Decks are engaged and aligned, you must connect the Manual Hi / Lo Drive Rod (Hi / Lo Rod).
3. The Foot Section Rod features a Sliding
Coupler, shown at right. With the Lanyard
Assembly disconnected (see below right),
slide the Foot Section Sliding Coupler
forward as shown at near right until the
small hole at the end aligns with the small
hole in the Head Section Rod.
Insertion of Retaining Lanyard
1. The Lanyard Assembly (690-8001-960)
should come pre-assembled with a Clevis
Pin, Washer, External Retaining Ring,
Lanyard, and Hair Pin Clip. It should also
be attached to the Lanyard Clip (100-1100-
053) on the side of the Hi / Lo Rod.
2. If the Hair Pin Clip is assembled within the
end of the Clevis Pin, pull it out.
3. Align the Coupler hole with the Hi / Lo Rod
hole and insert the Clevis Pin.
4. From the bottom, re-insert the Hair Pin Clip
into the end of the Clevis Pin to secure.
Lanyard
Assembly
08-670201-01
Lanyard Clip
100-1100-053
Hair Pin Clip
attached to
Lanyard
Clevis Pin
attached to
Lanyard
US5000-INS-LAB-RevA14 11

US5000 SEMI-ELECTRIC: FOOT / HEAD MOTOR INSTALLATION
Power Cord
faces this
direction
Motor
Cover
Foot / Head Motor 690-2001-912
(viewed from bottom)
FOOT END
HEAD END
Motor
Cover
1. Lay the bed deck on its side with legs extended as shown above. Ensure bed Head and Foot
Sections are connected as described on pages 8, 9, 10 and 12.
2. Slide the Motor Covers outward and let them dangle — they should be attached with Lanyards
to prevent misplacement.
3. Position the Foot / Head Motor so the
Power Cord is facing upward as shown
above. There is a label on the top of the
motor which indicates Head and Foot
direction as shown in DETAIL A at right.
DETAIL A
Viewed from top of Motor
Motor Slide-On
Cover closed
Motor Slide-On
Cover closed
Head Foot
US5000-INS-LAB-RevA14 12

4. Align the two large rectangular holes (Motor
Cam Chambers) on the Motor Ends with two
Motor Cams - one on the Head Section and
one on the Foot Section - as shown at right.
5. Push the Motor onto the Cams, ensuring
the Crossbrace Tubes are seated within the
Motor Cam Chamber cutouts as shown in
DETAIL B at lower right.
6. Once the Motor is in place, push with enough
force to snap it onto the Cams to secure it.
7. IMPORTANT: Replace the two Motor Covers
by sliding them back into place as shown in
DETAIL A on previous page.
Motor hooked onto Head Deck and
Knee Deck Motor Cams
Crossbrace Tubes
MUST seat into
Motor Chamber
cutouts on BOTH
Foot and Head Ends
DETAIL B
US5000-INS-LAB-RevA14 13

ASSEMBLY INSTRUCTIONS: US6000 FULL ELECTRIC
s NOTICE: Perform the steps on this page rst after removal of bed from carton. The
Hi / Lo Motor must rst be attached to each bed section and secured with the Lanyard
BEFORE assembling the Patriot LX sections together.
US6000 FULL ELECTRIC: HI / LO MOTOR ASSEMBLY, HEAD SECTION AND FOOT
SECTION
HEAD
SECTION
FOOT
SECTION
Closeup of Lanyard Assembly
with Clevis Pin and Locking Pin
Clip Attaching Motor Tube
to Frame Bracket
Leg Weldment
Motor Tube
Nylon
Shipping Tie
Nylon
Shipping Tie
Arm Tubes with
Spring Button
Arm Tubes with
Spring Button
Leg Weldment
1. Slide the Head or Foot Section out of the carton and lay it at, deck grid down, as shown at
right above.
2. The motor tube is secured to the end frame with a nylon shipping tie. Cut off and remove the
nylon shipping tie. Do not remove the Lanyard and Pin Assembly attached to the frame.
3. Lift the leg weldment slightly to allow the arm tube spring pins to pop out. Lower the leg
weldment until the spring pins are ush against the bed frame. Align the motor tube holes with
the motor mount U-bracket holes.
The motor tube can be extended by turning the motor tube clockwise several times if minor
adjustment is still necessary.
US5000-INS-LAB-RevA14 14

4. Insert the clevis pin through the holes and secure with the locking pin. See the following
instruction for locking pin installation.
Info: When the legs are lifted to align the holes in step 3, the spring buttons in the leg arm
tubes will be released and prevent the legs from returning to the low shipping position.
Once the Hi / Lo Motor is attached there is no need to disassemble the clevis pin and motor
again unless you are inserting it back into the shipping carton. After you disassemble the
motor for carton reuse, the arm spring pins will have to be depressed manually to allow the
legs to lower to shipping height.
Motor Locking Pin Installation
(Refer to Pictures at Right)
1. Insert locking pin into clevis pin hole.
2. Install locking pin through clevis pin hole.
3. Locking pin is shown locked into place on
clevis pin.
4. To remove locking pin: lift locking pin up and
push it back through clevis pin hole and out
of clevis pin.
Motor tube is shown at right locked into place.
Locking Pin
Clevis Pin
lift up
push back
US5000-INS-LAB-RevA14 15

US6000 FULL ELECTRIC: HEAD SECTION TO FOOT SECTION ASSEMBLY
Slot Pin
Slot Pin
Motor Cams
FOOT
SECTION
HEAD
SECTION
1. Place the Head and Foot Sections on their sides at approximately right angles to each other
with Motor Cams up, as shown above.
2. Slide the Head and Foot Sections together until the Head Section’s Pins seat into the Foot
Section’s Slots on both sides. Ensure the Pins are completely seated before continuing.
FOOT
HEAD
Straighten
Head
Wing
3. With the Pins fully seated in the Slots as described in step 2, rotate and straighten the bed as
shown above. Position Head Wing as shown above.
US5000-INS-LAB-RevA14 16

DETAIL A
Viewed from top of Motor
Motor Slide-On
Cover closed
Motor Slide-On
Cover closed
Head Foot
US6000 FULL ELECTRIC: FOOT / HEAD MOTOR INSTALLATION
FOOT END
HEAD END
Power Cord
faces this
direction
Motor Cover
Foot / Head Motor 690-8004-912
(viewed from bottom)
Motor Cover
1. Lay the bed deck on its side with legs extended as shown above. Ensure bed Head and Foot
Sections are connected as described on pages 8, 9, 11 and 12.
2. Slide the Motor Covers outward and let them dangle — they should be attached with Lanyards
to prevent misplacement.
3. Position the Foot / Head Motor so the
Power Cord is facing upward as shown
above. There is a label on the top of the
motor which indicates Head and Foot
direction as shown in DETAIL A at right.
US5000-INS-LAB-RevA14 17

Motor hooked onto Head Deck and
Knee Deck Motor Cams
Crossbrace Tubes
MUST seat into
Motor Chamber
cutouts on BOTH
Foot and Head Ends
DETAIL B
Hi / Lo Motor
Cord Retainer Clips
Y-Cable
Hi / Lo Motor
Plugs
4. Align the two large rectangular holes (Motor
Cam Chambers) on the Motor Ends with two
Motor Cams - one on the Head Section and
one on the Foot Section - as shown at right.
5. Push the Motor onto the Cams, ensuring
the Crossbrace Tubes are seated within the
Motor Cam Chamber cutouts as shown in
DETAIL B at lower right.
6. Once the Motor is in place, push with enough
force to snap it onto the Cams to secure it.
7. IMPORTANT: Replace the two Motor Covers
by sliding them back into place as shown in
DETAIL A on previous page.
8. After the Head / Foot Motor has been
installed and the Slide Motor Covers have
been attached, take note of the Hi / Lo Motor
Cord Routings shown on the next page.
The Head Motor Cord with loop is retained
under the Head Motor Crossbrace Tube. The
Foot Motor Cord is retained under the Leg
Lift Tube but is routed over the Knee Motor
Crossbrace Tube.
9. With the Motor Cords routed properly, plug
the Hi / Lo Motor Plugs into the Y-Cable
secured to the Head / Foot Motor.
10. After plugging in the Hi / Lo Motors, insert the
Motor Cords below the Motor Plugs into the
Cord Retainer Clips. Insure the Motor Plugs
are completely inserted into the Y-Cable and
the Y-Cable is completely inserted into the
Head / Foot Motor Port, next to the Pendant
Port.
US5000-INS-LAB-RevA14 18

Head Hi / Lo Motor Routing
Foot Hi / Lo Motor Routing
Cord Loop
Motor Cable Retainer
Head Crossbrace
Knee Crossbrace
Leg Lift Tube
Motor Cable Retainer
US6000 FULL ELECTRIC: HI / LO MOTOR CORD ROUTING
The Head Motor Cord has been looped
at the factory to shorten the coiled cord
and held with a Cable Retainer under
the Head Motor Crossbrace. The view at
right shows underside of bed.
The Foot Motor Cord is secured under
the Foot Leg Lift Tube. When plugging in
Foot Motor route the motor cord over
the Knee Motor Crossbrace. The view at
right shows underside of bed.
US5000-INS-LAB-RevA14 19

ASSEMBLY INSTRUCTIONS: US5000 / US6000
US5000 / US6000: POWER CORD ROUTING AND ATTACHMENT TO MAIN FRAME
RAIL
After bed assembly, secure the Power Cord to the Main Frame Rail with Cable Ties so that there
are no pinch points or interference.
Ensure there is a little slack so the Power Cord does not pull too tight when decks are raised and
lowered, but not too much slack — the Power Cord must not dangle in such a way that it may
catch on any bed part or accessory.
The Power Cord is hardwired into the Foot / Head Motor. Run the Power Cord along the outside of
the Main Frame Rail toward the bed head end as shown below (Note: US5000 is shown below, but
Power Cord routing and attachment is identical for US5000 and US6000).
s NOTICE: The Power Cord MUST be secured to the Main Frame Rail so there are no pinch
points or interference, and so it does not catch on any bed part or accessory.
Power Cord is hardwired into
Foot / Head Motor —
run Power Cord along outside
of Main Frame Rail toward head
end of bed.
Secure Power Cord to Main
Frame Rail with
Cable Ties so
there are no pinch points or interference.
Ensure there is a little slack so
the Power Cord
does not pull too
tight when
decks are raised and
lowered, but not too much slack —
Power Cord must not dangle in
such a way that it may catch on
any bed part or accessory.
HEAD END
FOOT END
US5000-INS-LAB-RevA14 20