lumz LED PT 1011 User manual

10
250
250 170
600
100
150
480
100
900
150
780
HEX NUT
WASHER
J-BOLT
BASE
PLATE
CABLE
HOLE
POLE
SERVICE
DOOR
FUSE
PLATE
SCREW
PROVIDED
SCREW
PROVIDED
!
1
2
we brighten up your life
LUMZ PTE LTD
INSTALLATION MANUAL
LED PT 1011
Factory:
No.14, Jalan Anggerik Mokara 31/44, Kota Kemuning Seksyen 31,
40460 Shah Alam, Selangor, Malaysia.
Tel: [phone]
Fax: [phone]
Email: [email protected]
o
o
o
o
o
o
o
Housing made of die-cast aluminium
Impact resistance tempered glass cover
Stainless steel screws
Operating temperature: -20°C~+40°C.
LED lifetime up to 50,000 hours
Voltage range: 100 - 277 VAC ~ 50 /60 Hz
Wattage: 40 W & 52 W
PRODUCT DESCRIPTION & DIMENSION
IP 65 IK 08 CLASS I WITH INTERGRAL DRIVER
WARNING
!
MAKE SURE POWER IS DISCONNECTED UNTIL INSTALLATION OF PRODUCT IS COMPLETELY FINISHED.
FAILURE TO DO SO COULD RESULT IN ELECTRICAL SHOCK CAUSING SERIOUS INJURY OR DEATH.
PTL-14A-J-W40-30-xx
PTL-14A-J-W40-40-xx
DESCRIPTION
MODEL:
Connect wires from the luminaire to AC power as follows:
1. Connect BLUE / BLACK wire to the NEUTRAL wire.
2. Connect GREEN / YELLOW-GREEN wire to the GROUND or EARTH wire.
3. Connect BROWN / RED wire to the LIVE wire.
POLE INSTALLATION
!
WIRING INSTALLATION
Singapore Office (HQ Sales & Marketing):
1 Coleman Street #10-06, The Adelphi,
179803, Singapore.
Tel: [phone]
[email protected]
www.lumzlighting.com
PT 1011/INSTALLATION MANUAL/REV.0
1/2
Connect all wires from the luminaire to AC power using a connector.
Make sure all wiring connections are tight so that no bare wires are visible.
Good connections may avoid tripping from happening.
BASE PLATE DIMENSION
# Make sure power is
disconnected before
installation
Fix pole to ground by
placing base plate over
the concrete and let all
bolts pass through base
plate holes.
Insert and tighten
washers & nuts.
SERVICE DOOR INSTALLATION
Place fuse plate inside
the pole and fix it with
screws provided.
Place service door on
surface of pole and fix it
with screws provided.
PTL-15A-J-W55-30-xx
PTL-15A-J-W55-40-xx
PTL-15B-J-W40-30-xx
PTL-15B-J-W40-40-xx
# Pole sold separately
Pole is available upon request, please consult us for more details.
LED PT 1011.K LED PT 1011.B
LED PT 1011.B
LED PT 1011.K

SET SCREW
SPIGOT
LUMINAIRE
POLE
SMALL HOLDER
BRACKET
!
1
3
2
we brighten up your life
LUMZ PTE LTD
INSTALLATION MANUAL
LED PT 1011
Factory:
No.14, Jalan Anggerik Mokara 31/44, Kota Kemuning Seksyen 31,
40460 Shah Alam, Selangor, Malaysia.
Tel: [phone]
Fax: [phone]
Email: [email protected]
Singapore Office (HQ Sales & Marketing):
1 Coleman Street #10-06, The Adelphi,
179803, Singapore.
Tel: [phone]
[email protected]
www.lumzlighting.com
PT 1011/INSTALLATION MANUAL/REV.0
2/2
Place luminaire on the pole by sliding it so that
small holder bracket on the pole is fully
covered by the spigot.
Insert set screws and screw it.
Make sure all screws fix tightly.
Connect wires with connector.
# Make sure power is disconnected before installation
Loosen all screws on
luminaire window for wiring.
LUMINAIRE INSTALLATION
Connect wires from the luminaire to AC power as follows:
1. Connect BLUE / BLACK wire to the 'N' NEUTRAL wire.
2. Connect GREEN / YELLOW-GREEN wire to the EARTH wire.
3. Connect BROWN / RED wire to the 'L' LIVE wire.
Tighten all screws on luminaire
window after completed wire
connection.