M-Power PMP2RS103 User manual

1
1.800.338.7337 / www.soundo󰀨signal.com
mPOWER Spoiler BRKT_Expedition 2018-2021 - English
0221
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
2018-2021 FORD EXPEDITION SPOILER BRACKET
•HIGH CURRENT interconnects must be properly terminated. Poor crimp quality can cause heat build-up and
re. Follow crimp connector manufacturer instructions.
•DO NOT install this product or route any wires in the Air Bag Deployment Zone. Refer to vehicle Owner’s
Manual for deployment zones.
•Do NOT use system to disconnect headlights, brake lights or other safety equipment.
•Unit may become hot to touch during normal operation.
•Failure to properly install connectors, fuses or wiring may cause vehicle failure or re.
•Installation must only be performed by trained technician. Installer must determine vehicle wiring
conguration and proper integration of system.
•Use proper wire gauge. All power wires connecting to positive (+) or negative (-) battery terminal or local
chassis ground (-) must be sized to supply at least 125% of max. current and properly fused at power source.
•Install protective grommets when routing wire through rewall or metal.
WARNING
FEATURES:
• Warning arrow greatly reduces install time through use of 3-wire
technology
• Functionality mimics the rear of a lightbar
• Integrates under the spoiler of the vehicle for a seamless look
• Available in single, dual or tricolor
PART NUMBERS:
• PMP2RS103: Rear Spoiler Bracket, 1 Module Kit, Black, for use with
mpower 4” Fascia Stud Mount Light – Ford Expedition 2018-2020
• PMP2RS203: Rear Spoiler Bracket, 2 Module Kit, Black, for use with
mpower 4” Fascia Stud Mount Light – Ford Expedition 2018-2020
• PMP2RS303: Rear Spoiler Bracket, 3 Module Kit, Black, for use with
mpower 4” Fascia Stud Mount Light – Ford Expedition 2018-2020
• PMP2RS403: Rear Spoiler Bracket, 4 Module Kit, Black, for use with
mpower 4” Fascia Stud Mount Light – Ford Expedition 2018-2020
COMPONENT
QUANTITY
PMP2RS103 PMP2RS203 PMP2RS303 PMP2RS403
2018-2020 Ford Expedition Left Bracket 1 1 1 1
2018-2020 Ford Expedition Right Bracket 1 1 1 1
6-32 Rubber Insert 4 4 6 6
6-32 X 1.00” Torx Screw 4 4 6 6
Installation Instruction Sheet 1 1 1 1
Product Warning Card 1 1 1 1
4 MODULE
3 MODULE
2 MODULE
1 MODULE
DRIVER’S SIDE SHOWN
PMP2RS(X)03 - For use with 4“ mpower fascia Stud Mount Light

2
1.800.338.7337 / www.soundo󰀨signal.com
mPOWER Spoiler BRKT_Expedition 2018-2021 - English
0221
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
2018-2021 FORD EXPEDITION SPOILER BRACKET
Fig. 2
INSTALLATION:
1. Remove rear spoiler from the vehicle using the
manufacturer’s recommended method. Lay the
included drill template onto the driver’s side of the
spoiler, as shown in Fig. 1. Line up the template
with the seam on the outer edge of the spoiler to
properly position it.
2. Secure the template in place with non-marking
tape.
3. Refer to the chart below and to the included
template for drill instructions:
4. Scribe the drill locations indicated by the template,
remove the template, and drill, as shown in Fig. 2.
Fig. 1
DRILL TEMPLATE
BRACKET TYPE MOUNTING HOLES
1 MODULE D, F
2 MODULE C, E
3 MODULE B, C, E
4 MODULE A, B, C
4 MODULE VERSION SHOWN
5/16” drill through rst wall of
spoiler for rubber inserts, number
of holes is dependent on number
of modules
3/4” drill through rst wall of
spoiler for wire pass through

3
1.800.338.7337 / www.soundo󰀨signal.com
mPOWER Spoiler BRKT_Expedition 2018-2021 - English
0221
NOTICE:
Installers and users must comply with all applicable federal, state and local laws regarding use and installation of warning devices.
Improper use or installation may void warranty coverage.
To review our Limited Warranty Statement & Return Policy for this or any SoundO Signal product, visit our website at www.soundosignal.com/tech-services/returns/.
If you have questions regarding this product, contact Technical Services, Monday - Friday, 8 a.m. to 5 p.m. ET at 1.800.338.7337 (press #4).
Questions or comments that do not require immediate attention may be emailed to techservices@soundosignal.com.
ENHANCING SAFETY THROUGH INNOVATION
2018-2021 FORD EXPEDITION SPOILER BRACKET
INSTALLATION (CONT).:
5. Flip the drill template over and lay on passenger’s
side. Temporarily, secure in place with non-
marking tape. Scribe the drill locations indicated
by the template.
6. Remove the template and drill as indicated.
7. Attach the lights to the included brackets, as
shown in Fig. 3. Secure nuts 1/8” turn past seated
contact.
8. Press the 6-32 rubber inserts into the spoiler. Then
place the bracket, as shown in Fig. 4. Route wires
through the wire pass through hole. Secure with
screws supplied. Repeat for opposite side.
9. Identify a location in which to drill a 1-3/8” hole
in the hatch sheet metal in order to place the
grommet and run wires into the vehicle.
10. Insert the provided grommet into the hole.
11. Run the wires into the hole and make nal
connections.
12. Before re-installing the rear spoiler, make all
electrical connections. Refer to the mpower arrow
kit instruction sheets for details.
Fig. 3
Fig. 4
Ifacongured,mpower® ArrowKitwas
purchased,skiptoStep8.
4 MODULE VERSION SHOWN
4 MODULE VERSION SHOWN
NOTE:Ifthehatchsheetmetalcontainsan
existingholetoroutewiresintothevehicle,
skiptoStep11.