M2I TOPR Series User manual

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
1 / 18
Thank you for purchasing the industrial HMI touch panel series of M2I corporation.
Please read this manual carefully to know installing, wiring, operating this equipment for safe use of this
product.
M2I Corporation
Industrial HMI Touch Panel
TOPR Series (Process Module)
Hardware Manual

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
2 / 18
Contents
Chapter 1 Safety Precautions................................................................................................................................................................. 3
■ Before using the product.............................................................................................................................................. 3
■ General Precautions ......................................................................................................................................................... 3
■ Design Precautions........................................................................................................................................................... 3
■ Wiring Precautions ........................................................................................................................................................... 3
■ Disposal Precautions........................................................................................................................................................ 4
■ Cell Type Battery Specifications and Exchange .................................................................................................. 4
Chapter 2 Overview .................................................................................................................................................................................... 5
2.1 Introduction of Products.............................................................................................................................................. 5
2.2 Package Contents............................................................................................................................................................ 5
2.3 Explanation of Model name ....................................................................................................................................... 6
Chapter 3 General Specifications ......................................................................................................................................................... 7
3.1 Electrical Specifications................................................................................................................................................. 7
Chapter 4 Parts Identification and Functions................................................................................................................................. 8
4.1 TOPRP Series ..................................................................................................................................................................... 8
Chapter 5 External Device Interface .................................................................................................................................................11
5.1 Serial Interface ................................................................................................................................................................11
5.2 Ethernet Communication Specifications.............................................................................................................12
5.3 USB Interface ...................................................................................................................................................................13
5.4 WLAN Specification [Only TOPRP20] ...................................................................................................................13
5.5 RCA Specification [Only TOPRP20]........................................................................................................................13
5.6 HDMI Specification [Only TOPRP20] ....................................................................................................................14
5.7 AUDIO Specification [Only TOPRP20]..................................................................................................................14
Chapter 6 Installation ..........................................................................................................................................................................14
Chapter 7 Wiring .......................................................................................................................................................................................14
7.1 Power wiring ....................................................................................................................................................................14
7.2 Ground wiring .................................................................................................................................................................15
Chapter 8 Maintenance ..........................................................................................................................................................................16
8.1 Cleaning the Display ....................................................................................................................................................16
8.2 Periodic Check Points..................................................................................................................................................16
8.3 Problems with the Device..........................................................................................................................................16
Chapter 9 Products and Warning Label Location ......................................................................................................................17
Chapter 10 Products Label....................................................................................................................................................................18
10.1 AC Power Models .......................................................................................................................................................18
10.2 DC Power Models .......................................................................................................................................................18

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
3 / 18
Chapter 1 Safety Precautions
■Before using the product
To use the product safely and effectively, please read the contents of this manual thoroughly before use.
Please keep to the safety precaution, for it is to prevent accidents and potential danger from occurring.
Safety precaution is classified into ‘Warning’ and ‘Caution’ and their meanings are as follows. Also the
indicated illustrations on the product and in the manual have the following meanings.
Violating the instruction may result in serious personal injury or death.
Violating the instruction may result in slight personal injury or product damage.
Be cautious, for danger may be present.
Be cautious, for there is a possibility of an electric shock.
■General Precautions
Do not press the screen with a hard or sharp object (awl, screwdriver, pen) with too strong a force.
It may cause malfunction of touch due to damage of the front sheet.
Do not use or store in an environment with high vibration.
Do not allow foreign objects such as water, liquids, or metal powders to enter the product. This may
cause breakage or electric shock.
Do not allow foreign objects such as water, liquids, or metal powders to enter into the front(screen)
protective sheet. The screen may be invisible or may cause a malfunction of the touch.
Use the radio or mobile phone at least 30cm away from the main unit.
Two or fewer bright spots may appear on the LCD screen, and certain areas may appear brighter, but
this is not a defect in LCD characteristics.
Do not store or operate in direct sunlight. Direct sunlight can change the properties of the LCD.
■Design Precautions
Install protection circuit on the outside of Products to protect the entire control system when external
power supply or Products have problems.
As the malfunction & incorrect result of Products could damage the stability of the entire systems
and human body, you must install damage preventing interlock circuit such as emergency stop,
Protective circuits, positioning upper and lower limit switch and interlock for forward/reverse
operation.
When computer or other controllers communicate and exchange data with products or change operation
mode of products, set up protective sequence program in PC or Controller for protecting system from
communication error.
The output signal or communication lines should be separated from the power line or high tension wire.
They should be installed 100mm (3.94 Inch) or more from each other.
■Wiring Precautions
Be sure the wiring is done correctly by checking the product’s rated voltage and the terminal layout.
Incorrect wiring could result in fire, damage or malfunctions.
Tighten the terminal screw with the specified torque. If the screws of terminal are loose, it could

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
4 / 18
result in short circuit, fire, malfunctions. FG Terminal must be used a dedicated ground. Not doing so
could result in malfunctions.
a. Grounding should be the Class 3 grounding. The cable for grounding should be more than 4㎟.
b. grounding point be closed to the products and make short the distance to the ground cable if possible.
Please see below.
■Installation Precautions
Do not install the location which exceeds allowed temperature. Product can be damaged or shorten
the life. Especially Install environment as below should be avoided.
Do not Install product to the place which the ambient temperature is out of limits, from 0℃to 50℃or on the
surface of control board which high pressure equipment is installed.
Do not install to the place where strong shock or vibration continuously have impacted on product.
The space between back of product and back of control board must be more than 100mm for maintenance
and ventilation.
In order to improve water retention and ventilation, the space between the back of the main body
and the console box should be 100mm or more, and install the cooling fan when installed in an
enclosed space.
■Disposal Precautions
When you dispose of product and battery, please treat it as industrial waste. It can create poisonous
substances or explosion.
■Cell Type Battery Specifications and Exchange
Mounted on mainboard Model MS920SE Battery is not replaced by the user. If the battery has run out of
service, please contact our Customer Support Center for replacement and inspection.
Item
Content
Battery Voltage
DC 3V
Battery Model
MS920SE (lithium / Rechargeable )
Battery lifetime
Permanent (In case of ambient temperature 25℃)
Battery Discharge
Last about 7 days After turn it off
*Depending on the model specifications are subject to change.
■All field-wiring connections to this unit shall be from Limited Voltage / Limited Current, below 24 Vdc
isolated secondary source with an output fuse, or Class 2.

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
5 / 18
Chapter 2 Overview
2.1 Introduction of Products
This industrial HMI touch panel is an industrial control device required in industrial field. It is a device
based on RS-232C and RS-422/485, Ethernet which is used for the basic purpose of communication with
another device (PLC).
2.2 Package Contents
The components of the product are as follows.
Before using the product, please check that all of the following components are included.
Item
Figure
Quantity
Process Module
1
Manual
1
Power Connector
1
Accessories
(Sold separate)
USB Memory
USB Cable
SD Card
Front Protect Sheet
User Options

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
6 / 18
2.3 Explanation of Model name
TOPR
T
□□
□□
□
□
-
Ex
Serise
Type
Screen Size
Option
Resolution
Power
-
Explosion proof
P : Process
08 : 8.4"
10,30 : Premium
Q : QVGA(320*240)
D : DC
Ex : Explosion proof or special model
D : Display
10 : 10.2", 10.4"
V : VGA(640*480)
A : AC
Blank: Non-explosion proof or
general model
T : P + D
12 : 12.1"
S : SVGA(800*600)
15 : 15"
X : XGA(1024*768)
* "S" for 12.1 "model: XGA
2.3.1 Process Module (Main Unit)
TOPR
P
□□
□
Series
Type
Option
Power
P : Process
10 : Standard
D : DC
D : Display
20 : Premium
A : AC
T : P + D
2.3.2 Display Module (Accessory Unit)
TOPR
D
□□
□□
□
Series
Type
Display Size
Option
Resolution
P : Process
08 : 8.4”
10 : Standard
Q : QVGA(320*240)
D : Display
10 : 10.4"
20 : Premium
V : VGA(640*480)
T : P + D
12 : 12.1”
30 : Premium
S : SVGA(800*600)
15 : 15”
X : XGA(1024*768)
W: WQVGA(480*272)
WVGA(800*480)

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
7 / 18
Chapter 3 General Specifications
3.1 Electrical Specifications
TOPRP10D
TOPRP20D
TOPRP10A
TOPRP20A
Power
Input Voltage
DC24V
AC220V,50/60Hz
Input Voltage Range
DC 20~28V
AC100~240V, 50/60Hz
Consumption
Power
Only Process
Under 6W
With
Display
Module
TOPRD08 Series
Under 12W
TOPRD10 Series
Under 15W
TOPRD12 Series
Under 15W
TOPRD15 Series
Under 18W
Voltage endurance
DC 24V, 10ms
AC85/170V, 10ms
Insulation Resistance
500VDC, 10 ㏁
3.2 Memory Specifications
Screen Memory
128MB
Backup Memory
512KB: System buffer(10K Word), Including Alarm/Log/Recipe
Backup Period
Permanent
Real Time Clock
Built in(by Battery)
3.3 Environment Specifications
Operation Temperature(℃)
-10 ~ +50
Storage Temperature(℃)
-20 ~ +60
Operation Humidity(%RH)
0 ~ 90(No dew)
Atmosphere
No corrosive gas
Vibration Endurance
Amplitude: 10≤F＜25 ㎐(2G) X,Y,Z each direction(for 30 minutes)
Noise Immunity
1000Vp-p(Pulse width 1 ㎲)
Static Electricity Discharge
Connective discharge from EN61000-4-2: ±4 ㎸
Shock Endurance
10G X,Y,Z each direction(for 3 times)
Surge Voltage
500V(Line-Line)
Ground Connection
Class 3(Under 100Ω)
Protection Classification
IP2X(Display Module: IP65)
3.4 Structure Specifications
Dimension(㎜)
201.6X147.6X39.8
Weight(㎏)
0.8Kg
Cooling System
Natural air circulation
Case Material
AL(Aluminium)
Model
Item

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
8 / 18
Chapter 4 Parts Identification and Functions
4.1 TOPRP Series
4.1.1 Product Dimension

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
9 / 18
4.1.2 Part Names and Specifications
No.
Part
Form
Description
①
Power Connector
TB 5mm 3P
TOPRP10D, TOPRP20D
TOPRP10A, TOPRP20A
DC 20V~28V
AC100~240V, 50/60Hz
②
COM3 Connector
TB 3.5mm 3P
RS-485 Serial Comm. with PLC
③
Extension Module Connector
-
Expansion module mounting cover
4.1.3 Side Part Names and Specifications
[TOPRP10] [TOPRP20]
No.
Part
Form
Description
Etc.
①
USB HOST
USB A type
Connector for option for USB storage. 5V/0.5A limit
②
HDMI
Standard HDMI
HDMI output terminal, external video device connection
(TV / Monitor connection). * Max resolution 1920X1080.
Only TOPRP20
③
RCA Jack
Composite RCA
Jack (Yellow)
VIDEO input terminal, external video device connection.
Input format: NTSC, PAL, SECAM
Only TOPRP20
④
AUDIO
3.5mm Audio
Plug
AUDIO output terminal, external speaker connection.
* Video, WAV file playback support.
Only TOPRP20
.

TOPR Series (Process Module) Hardware Manual
M2I Corporation
11-35, Simin-daero 327beon-gil, Dongan-gu, Anyang-si, Gyeonggi-do 14055, Korea, Tel: [phone], Fax: [phone], www.m2i.co.kr
10 / 18
4.1.4 Top Part Names and Specifications
No.
Part
Form
Description
Etc.
①
External antenna
connector
SMA FEMALE
External antenna connector
Only TOPRP20
②
SD Card Cover
Plastic Cover
SD Card, Reset Switch, Mode Switch
included
③
SD Card Socket
SD Card Socket
Data upload / download
④
Cover Sensor
Photo coupler
Cover open / close detection
⑤
Mode Switch
DIP Switch 2P
Set Up System Mode
⑥
Reset Switch
Tact Switch
System reset Switch
4.1.5 Bottom Part Names and Specifications
No.
Part
Form
Description
Etc.
①
ETHERNET Connector
RJ45
10BASE-T/100BASE-TX, Auto-MDIX
2ch.
②
COM1
DSUB9
RS-232C/422/485 Serial Comm. with PLC
(Switchable the Comm. Software select)
③
COM2
DSUB9
RS-232C/422/485 Serial Comm. with PLC
(Switchable the Comm. Software select)